Manualshelf

Installation Guide

ManualsBrandsUnbranded ManualsFencing6 in. x 6 in. Steel Post Anchor for Wood
12
T
1-866-577-8868
www.titanbp.com
More beautiful decks...More beautiful decks...
Real easy.Real easy.
T
1-866-577-8868
www.titanbp.com
More beautiful decks...
More beautiful decks...
Real easy.
Real easy.
USE ON CONCRETE, STONE AND COMPOSITE SURFACES.USE ON CONCRETE, STONE AND COMPOSITE SURFACES.
FOR RAIL, FENCE, PERGOLA POSTS AND MORE.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
INSTALLATION
|
STRUCTURAL WOOD POST ANCHOR KITSTRUCTURAL WOOD POST ANCHOR KIT
4x4 / 6x64x4 / 6x6
2 3
5
1
4 6
PARTPART
2 2
OFOF
2 2
SIDESIDE
1 1
OFOF
2 2
STRUCTURAL WOOD POST
ANCHOR KIT
(1) Base, (1) Tube ,
(2) Set Screw Plates, (4) Set Screws, (2) Locking pins,
(1) Threaded Stud, (1) Bracket ( 4x4, soft wood only )
Concrete fasteners sold separately.
Wedge Bolts®
WOOD FILLER, SANDPAPER,
PUTTY KNIFE
Sold separately.
TITAN STRUCTURAL WOOD POST ANCHOR KIT / TSPA35 / TSPA55
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
TAPTAP tube into bore tube into bore
withwith V-CUT V-CUT facing facing
side of post.side of post.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
9-1/2"9-1/2"
10-1/2"10-1/2"
C
C
11- 1/2"11- 1/2"
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
3"
1/4"
MIN.
MC
3"
1/4"
MIN.
3"
1/4"
MIN.
TOOLS NEEDED
DRILL
SOCKET
HAMMER
1-1/4" x 18" Ship Auger Grease
1/2" Twist bit
1/8" Allen Key
CHECK IT CHECK IT
OUTOUT
!!
POST WRENCH
See step 10
START
BOREBORE 1-1/4" diameter 1-1/4" diameter
hole to 11-1/2" deep.hole to 11-1/2" deep.
3"
1/4"
MIN.
TAPTAP tube tube ush with ush with
bottom of post.bottom of post.
Insert Insert threaded stud threaded stud
into nut inside tube.into nut inside tube.
Using a scrap of wood, Using a scrap of wood,
TAPTAP studstud to set tube to set tube
1/16" to 1/8" below 1/16" to 1/8" below
surface of post.surface of post.
1/16"-1/8"
MARKMARK the 2 locking pin the 2 locking pin holes location holes location
inin Center Center of post as shown. of post as shown.
3"
1/4"
MIN.
TAP the 2 locking pins into holes and set them
1/8" inside of post.DRILL with 1/2"Twist bit to the
opposite sideopposite side of post.
4X4 ONLY4X4 ONLY
3"
1/4"
MIN.
OPTIONALOPTIONAL

Summary of content (2 pages)