User manual

ManualsBrandsUnbranded ManualsHeadphonesBluetooth® (1075101) Headphone Basetech On-ear Headset Black

• Ensure that Bluetooth

is enabled and that the Bluetooth

device that you wish to pair

features all of the necessary Bluetooth

drivers. Visit the manufacturer's website to download

and install the latest drivers.

• To switch to the pairing mode, press and hold the multifunction button (5) when the

headphones are switched off until the red and blue LEDs (7) ash alternately. You will hear

"POWER ON" followed by "PAIRING" through the headphones.

• Follow the instructions for your Bluetooth

device. These may vary depending on the

manufacturer and design.

• Select "BH-530" on your audio playback device (e.g. mobile phone, laptop) to pair it with the

headphones.

• You will hear "Pairing Completed" through the headphones once the pairing process is

complete. Your audio playback device will also conrm that it was paired successfully with

your headphones. The message displayed will vary depending on your device. The blue

LED (7) will ash every 5 seconds when the headphones are switched on and paired with an

audio playback device.

• You may need to enter a password when pairing the headphones with Bluetooth

devices.

Enter the password (or try using "0000") and conrm your entry.

• If pairing fails, turn off the headphones and try pairing them again following the steps outlined

above.

Up to two Bluetooth

devices may be connected to the headphones at the same

time (Multi-link technology). Repeat the above steps to pair the headphones with

a second Bluetooth

device.

• If either of the devices paired via Bluetooth

is switched off, the Bluetooth

connection will

be automatically re-established when the device is switched on and Bluetooth

is enabled

(unless the device is unpaired). If the Bluetooth

connection is not re-established (e.g. when

the headphones are in standby mode), briey press the multifunction button (5) to pair the

headphones with the previously connected Bluetooth

device.

Ensure that you enable automatic connection in the settings for your

device's operating system. This may be necessary for devices such as Nokia

smartphones.

d) Making and receiving calls

Voice commands must correspond to the features supported on your

smartphone. You can dial a contact using voice commands, e.g. numbers or

nicknames. The headphones only support English voice commands.

• Press and hold the multifunction button (5) for approximately 1 second. You will hear a beep

when you release the button. Audio playback will be suspended.

• Issue the voice command corresponding to the contact that you wish to dial. Follow the

instructions for your smartphone. The phone app will dial the contact and connect the call.

• To redial the most recently dialled number, press the multifunction button twice in quick

succession.

• Press the + button (3) to increase the volume. Press the – button (1) to decrease the volume.

You will hear a beep when the maximum/minimum volume is reached.

• Briey press the multifunction button to answer an incoming call.

• Press and hold the multifunction button for approx. 1 second to decline an incoming call.

e) Listening to music

• Launch the music software/app on the audio playback device that you paired with the

headphones.

• Start the music playback on your device or briey press the multifunction button (5).

• Briey press the multifunction button to pause playback.

• Press the > button (6) to skip to the next track in the playlist.

• Press the < button (2) to go back to the beginning of the current track.

• Press the + button (3) to increase the volume. Press the – button (1) to decrease the volume.

You will hear a beep when the maximum/minimum volume is reached.

Some smartphones play music directly through their built-in speakers. If so,

adjust the Bluetooth

settings accordingly so that the audio is transmitted via

Bluetooth

and played through the headphones. Read the user guide for your

audio playback device for information on how to congure the settings.

Troubleshooting

• Ensure that all of the necessary Bluetooth

drivers are installed and up-to-date if some

features do not work properly.

• Please note that the remote control feature on the headphones is not supported by all audio

playback devices (e.g. smartphones). Check the list of features for your device (the AVRCP

protocol must be supported) and visit the website of your smartphone manufacturer. Updating

your device may help to resolve the issue.

• Some smartphone models route answered calls directly to the phone. The call can be

received on your phone or redirected to the headphones. Read the user guide for your device

for more information.

• Please note that the operating tones may vary depending on your device.

Maintenance and cleaning

Never use aggressive and abrasive detergents, rubbing alcohol or other

chemical solutions, as these could damage the casing or even impair the

functioning of the product.

• Disconnect the power supply from the product before cleaning.

• Use a soft, antistatic and lint-free cloth to clean the device.

• Dust can be easily removed using a clean and soft brush.

Declaration of conformity (DOC)

We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that

this product conforms to the fundamental requirements and the other relevant regulations of

the directive 1999/5/EC.

The Declaration of Conformity for this product can be found at www.conrad.com.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the

household waste.

At the end of its service life, dispose of the product according to the relevant

statutory regulations.

You thus full your statutory obligations and contribute to the protection of the environment.

Technical data

Input voltage / current ...........................5 V/DC, 500 mA

Battery type ..........................................Lithium polymer rechargeable battery

Battery capacity .................................... 110 mAh

Charging time ....................................... 3 hours (full charge)

Range ................................................... Up to 10 m

Bluetooth

version ................................3.0 + EDR

Bluetooth

prole .................................. HSP, HFP, A2DP, AVRCP

Call time ................................................Up to 11 hours

Audio playback ..................................... Up to 10 hours

Standby ................................................Approx. 250 hours

Frequency response .............................20 Hz - 20000 Hz

Sensitivity .............................................85 dB / nW ± 3 dB

Impedance ............................................32 Ω ± 15 %

Directivity .............................................. Omnidirectional

Cable length (USB charging cable) ...... 1 m

Operating conditions .............................0 to +60 ºC, 20 – 85% RH

Storage conditions ................................-10 to +80 ºC, 20 – 85% RH

Dimensions (W x H x D) .......................170 x 175 x 70 mm

Weight ..................................................approx. 155 g

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the

technical status at the time of printing.