SDS

BIO-CLEAN HARD WATER STAIN REMOVER
Version: 001 Date issued: 28. 04. 2015 Revision Date: N/A Page 2 of 3
5. Fire-Fighting Measures
Suitable Extinguishing Media: Not applicable. Product is not a fire hazard.
Unsuitable Extinguishing Media: High pressure water jet. Specific hazards in case of fire: None known.
Special Fire Fighting Precautions: Fire fighters should wear appropriate protective equipment, including self-contained
breathing apparatus and impervious clothing.
6. Accidental Release Measures
Emergency Procedures: Depending on the extent of release, consider the need for emergency responders with adequate
personal protective equipment for clean-up, need for evacuation or restriction to access of spill area.
Personal Precautions: Do not eat, drink or smoke during clean up. Wear protective clothing, eye protection and impervious
gloves (e.g. neoprene). Wash thoroughly after clean up.
Environmental Precautions: Prevent spills from entering storm sewers/drains or contact with soil.
Clean up Methods: Small spills may be wiped up and rinsed with water. For larger spills, contain spill with inert material
(sand, clay). Transfer material to labeled containers for recovery or proper disposal. After removal, flush area with water.
7. Handling and Storage
Precautions for Safe Handling: Read label before use. Avoid contact with skin or eyes. Wear protective gloves, eye
protection, face protection. Use only according to label directions. If unsure about safe use, contact your supervisor. Do not
eat, drink or smoke while using this product. Wash hands, face and any skin contact thoroughly after handling.
Conditions for Safe Storage: Do not contaminate water, food or feed by storage and disposal. Store in tightly closed, original
container in a cool (10° - 30°C), dry area. Keep in an area inaccessible to children. Incompatibility: None known.
8. Exposure Controls / Personal Protection
Components with occupational exposure limits:
Component Reference TWA PEL
Silica ACGIH(TLV) 0.025 mg/m
3
OSHA 0.1 mg/m
3
NIOSH(REL) 0.05 mg/m
3
Engineering Controls: Proper ventilation in accordance with good industrial hygiene should be provided.
Personal Protective Equipment
Respiratory: Respiratory protection is not necessary under normal conditions of use. If necessary to prevent exposure above
occupational limits, use an approved cartridge style respirator.
Gloves: Use water impervious gloves (latex or neoprene rubber). No breakthrough time has been established.
Eye Protection: Chemical resistant goggles or face protection.
Other: Protective clothing (long sleeves, pants), eyewash, safety shower are always advisable when working with chemicals.
9. Physical and Chemical Properties
Physical State - Slurry Auto-ignition temperature - Not applicable
Color - Green Flash Point - None
Odor - Mint Flammability - Not applicable
Odor Threshold - Not available Flammability Limits - Not applicable
Boiling Point - 212°F Partition coefficient - Not applicable
Decomposition temperature - No data available Solubility (Water) - Complete
Freezing Point - 32°F Vapor Density - Not available
pH (Neat) - 2.1 - 3.1 Vapor Pressure - Not available
Relative Density - 1.25 Viscosity - Viscous slurry
Evaporation Rate - Similar to water % VOC - < 1 (Excluding exempt material)
10. Stability and Reactivity
Reactivity: No specific reactivity test data is available for this mixture. Under normal conditions of storage and use, hazardous
reactions are not expected. Incompatible materials: None known.
Chemical stability: This product is stable at ambient temperatures and atmospheric pressures.
Conditions to avoid: Temperatures above 50°C or below 10°C. Hazardous decomposition products: None known.
11. Toxicological Information
Acute Toxicity: Toxicity data is not available for this mixture. Data below are estimates based on summation methods.
Test Results Classification (A.0.4.1(c)) Basis (A.1.3.6.1)
Oral > 1075mg/kg Category 4 Ingredient literature (Additive formula)
Dermal > 2000mg/kg Not applicable Ingredient literature (Additive formula)
Inhalation > 20 mg/L Not applicable Ingredient literature (Additive formula)
Eye Damage/Irritation Corrosion Category 1 Ingredient literature
Skin Damage/Irritation Irritation Category 2 Ingredient literature
Summary: Skin and eye contact are most likely routes of exposure. Exposure causes skin irritation and serious eye damage.