Installation Guide

AQUASPEC FAUCETS
MODEL - Z82200-XL SERIES
SINGLE CONTROL FAUCET
TECHNICAL INFORMATION
FLOW: 2.2 GPM [8.3L] PRESSURE COMPENSATING AERATOR*
MAXIMUM PRESSURE: 125 PSI
MAXIMUM TEMPERATURE: 160
O
F
F
CARTRIDGE STYLE - CERAMIC DISC MIXING CARTRIDGE WITH TEMPERATURE LIMIT STOP
®
* AN AERATOR WITH A MAXIMUM FLOW RATE OF 2.2 GPM (8.3L/min) MUST BE INSTALLED FOR THIS FAUCET MODEL TO
MEET THE REQUIREMENTS OF CSA B125.1/ASME A112.18.1
INSTALLATION INSTRUCTIONS
PAGE 1 OF 3
IMPORTANTTHE WATER SUPPLY LINES MUST BE THOROUGHLY FLUSHED BEFORE INSTALLATION TO PREVENT
FOREIGN MATTER AND DEBRIS FROM CLOGGING AND/OR DAMAGING INTERNAL COMPONENTS AND THEREBY PREVENTING
THE FAUCET FROM FUNCTIONING PROPERLY
1. SECURE GASKET (ITEM # 9A) WITH ADHESIVE BACKING TO UNDERSIDE OF FAUCET BODY.
2. PLACE FAUCET ON SINK THROUGH PRE-DRILLED MOUNTING HOLE IN SINK.
3. PLACE MOUNTING RING (ITEM #9C) ONTO MOUNTING STUD (ITEM #7). FLAT SIDE OF MOUNTING RING SHOULD
FACE UNDERSIDE OF SINK.
4. ROTATE FAUCET BODY (ITEM #5) TO DESIRED ALIGNMENT AND SECURE TO SINK USING MOUNTING NUT (ITEM #9B)
ON MOUNTING STUD (ITEM #7). HEX SIDE OF MOUNTING NUT SHOULD FACE DOWN TO ALLOW ACCESS TO HEX
NUT AND/OR SCREW SLOT. DO NOT OVER TIGHTEN.
5. INSTALL HANDLE (ITEM #1A)
5.1. REMOVE COLORED HOT/COLD INDEX (ITEM #1C) FROM HANDLE BY PRESSING OUT FROM UNDERSIDE OF
HANDLE (ITEM #1A)
5.2. LOOSEN SETSCREW (ITEM #1B) USING 1/8” ALLEN WRENCH.
5.3. SLIDE HANDLE ONTO STEM OF CERAMIC MIXING CARTRIDGE (ITEM #4)
5.4. TIGHTEN SETSCREW (ITEM #1B) USING 1/8” ALLEN WRENCH. DO NO OVER TIGHTEN.
5.5. PRESS COLORED HOT/COLD INDEX (ITEM #1C) INTO HANDLE.
6. ATTACH LAVATORY SUPPLIES TO BRAIDED FLEX HOSES (ITEM #8)
7. OPTIONAL: POP-UP DRAIN (-P)
GRID STRAINER DRAIN (-G)
INSTALL POP-UP DRAIN OR GRID STRAINER DRAIN IN SINK OUTLET AND PLUMB WASTE CONNECTION.
8. TURN SUPPLY WATER ON AND OPERATE FAUCET CHECKING FOR LEAKS.
9. INSTALL AERATOR INTO FAUCET AND HAND TIGHTEN INTO FAUCET SPOUT. IT MAY BE NECESSARY TO REMOVE AND
CLEAN THE AERATOR AT START UP.
ZURN INDUSTRIES, LLC
♦♦
♦♦
♦ COMMERCIAL BRASS OPERATION
♦♦
♦♦
♦ 2640 SOUTH WORK STREET
♦♦
♦♦
♦ FALCONER NY 14733
Phone: [phone]
♦♦
♦♦
♦ Fax: [phone]
♦♦
♦♦
♦ www.zurn.com
In Canada: ZURN INDUSTRIES LIMITED
♦♦
♦♦
♦ 3544 Nashua Drive
♦♦
♦♦
♦ Mississauga, Ontario L4V1L2
♦♦
♦♦
♦ Phone: [phone] Fax: [phone]
Form # CF1556 Date: 12/30/10
C.N. No. 127255 Rev.