User guide

2233-0250-0513-V01
SCENE SET-UP
Install the Wallscape FX ActivatorTM on your Wall
Before installing your Activator, move the function sw itch on the
back of the Activator from “Try Me” to “Play”. This will enable full
special eects functionality.
The Activator should only be mounted on a vertical surface. For
optimal results, place a nail or screw into the wall approximately
4 feet from the oor. Then, position the Activator onto the wall by
placing the hang hole on the back of activator directly over the nail
until securely in place.
Note: For rooms with ceilings higher than 8 feet, you may want to
position the activator higher than 4 feet to ensure that the light
suciently illuminates the wall and the ceiling.
Wall Decal Preparation
After removing the decals from the package, roll out the sheet and lay
at for 24 – 48 hours until the sheet no longer wants to curl back up.
For best results apply the decals onto smooth, clean surfaces. The decals
may not stick to heavily textured surfaces. Do not apply to fresh paint or
wallpaper. Let the new paint/wallpaper dry for at least 3 weeks. Before
applying the decals to wallpaper or other delicate surfaces, test one in an
inconspicuous area. Keep the decals away from cribs and out of reach of
young children to prevent choking hazard.
Create your Scene by placing the Wall Decals
To apply each decal, carefully peel it o from the sheet. Then, place and
smooth the decal onto your wall in the desired location. To remove or
reposition each decal, just carefully peel it o from the wall. Kids can follow
the suggested scene layout or customize and create their own scene. For
optimal function with the light eects, please note the following suggestions
on wall decal placement:
• Begin with the lowest decal positioned 6 inches above the top of the
Activator.
• Then, place the bottom of Tinker Bell’s shoes approximately 15 inches above
the top of the Activator.
• Place all other decals around Tinker Bell but ideally no more than 36 inches above
the top of the Activator. This will help to ensure that all decals are illuminated by
the light cast.
On textured walls, periodically check the decals to make sure they are remaining at
against the surface. Gently smooth any parts of the decal, that appear to be lifting o the
surface. Repeat as needed until the decals remain at against the surface.
SCENE ACTIVATION
Now you can activate your scene using dierent programming modes on the
Activator as follows:
TRY ME (10 second demo)
This is the factory default program and is used for in store demonstration. It is
not intended for home use and has limited functionality. For full functionality,
move the function switch on the back of the Activator from “Try Me” to “Play”.
MODE 1 – FULL FUNCTIONALITY LIGHT & SOUND SHOW
Press the program button once to activate. This will enable full light and
sound special eects including the following:
• Nature and Pixie Dust sound eects
• Light gently fading in and out, illuminating your wall and ceiling
• Synchronized lights and sounds that bring the scene to life.
In this mode, auto shut-o of the sound will occur approximately after 5 minutes and auto
shut-o of the light will occur approximately after 10 minutes.
MODE 2 – LIGHT SHOW ONLY
Press the program button two times to activate. This will enable full light functionality but will
not include any sound eects. Auto shut-o will occur approximately after 20 minutes.
MANUAL SHUT-OFF
To manually turn o the Activator, press and hold down the program button for approximately
two seconds until the light and sound turns o.
BATTERY REPLACEMENT
Tool required - Small Phillips head screwdriver
Requires 3 AA/LR6 alkaline batteries.
1. Using a Phillips head screwdriver, remove the battery cover.
2. Insert 3 AA/LR6 alkaline batteries as indicated in the battery
compartment and replace cover.
3. IMPORTANT! Switch the Activator to the PLAY position before
hanging on the wall.
© Disney.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Caution: changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
MANUFACTURED BY UNCLE MILTON INDUSTRIES, INC.
P.O. Box 6281, THOUSAND OAKS, CA 91359 USA
©2013 UMI. All rights reserved. ® and TM designate
trademarks of Uncle Milton Industries, Inc.
MADE IN CHINA
BATTERY SAFETY INFORMATION
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Dierent types of batteries or new and used batteries are not to be mixed.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
• Do not dispose of batteries in re. Battery may explode or leak.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE — DO NOT DISCARD
Questions? Visit unclemilton.com
Function
Switch
Hang
Hole
Battery
Cover
TRY ME
PL AY
Program
Button
FOR BEST ILLUMINATION, USE IN A DARKENED ROOM.