Configuration and User Guide VideoEdge® IP SpeedDome Camera Version 1.
Notice The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Copyright Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form, in whole or in part, without prior written consent of Tyco International Ltd. © Copyright 2009 and its Respective Companies.
Warning To Reduce Risk of electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel. Do not expose this appliance to rain or moisture. Do not install this product in hazardous areas where highly combustible or explosive products are stored or used. The lightning flash/arrowhead symbol, within an equilateral triangle, alerts the user to the presence of a shock hazard within the product’s enclosure. IT E161302 Underwriters Laboratories Inc.
iv Configuration and User Guide
Table of Contents Introduction 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ACC compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Frame Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Scans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using Scan as Home Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using Sequence as Home Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Privacy Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Scheduled Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Task Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Camera Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Physical Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Technical specification 9 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Camera Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Adding a Privacy Zone screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Privacy Zone being selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Privacy Zone Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 Privacy Zone confirmed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 Select Zone . . . . . . . . . . . . . . . . . .
Table of Contents FTP Settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 Firewall Settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12 Address List section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 Maintenance screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14 Advanced screen. . . . . . . . . .
Table of Contents Using a Sequence as a Home Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Delete a Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Add Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Defining Privacy Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Selecting a Privacy Zone. . . . . . . . . . .
Table of Contents Deleting a Scheduled Task . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20 Configuring the Web GUI ACC Frame Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22 Configuring Alarm Video Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22 Setting RSTP Timeout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23 Configuring Audio Input. . . . . . . . . . . . . . . . . . . .
Table of Contents Corresponding IR Switching with IR Illumination at 850nM . . . . . . . . . . . . . . . 4-37 IR Mode Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37 AGC and Open Shutter relationship . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Camera Specifications . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Overview The VideoEdge® IP SpeedDome Camera (hereafter referred to as IP Dome) operates across an IP network, e.g. the Internet, a LAN or WAN. The video output from the camera is compressed and sent across the network using IP transport mechanisms. PTZ camera control outputs from IPconnected controllers will be passed to the dome control electronics, allowing complete functionality as existing domes at a remote location connected by any kind of IP network.
Introduction Features The following provides information on the features of the IP Dome. ACC compression Three quality levels (Super, Normal, and Extended Record) are available on the camera. Two sensitivity levels (Normal and High) are available on the camera. Frame Rates CIF NTSC PAL 4CIF 30 IPS 25 IPS 2CIF 30 IPS 25 IPS 1CIF 30 IPS 25 IPS Table 1-1 — Frame Rates The IP Dome supports a maximum or 30/25 (NTSC/PAL) images per second per video channel at 4 CIF.
Introduction This may continue until the total bandwidth reaches 85% of the upper limit, in order to prevent instability due to continuous throttling. The video quality cannot be increased beyond the original user configured quality. The throttling is not carried out on any MJPEG codec if it is only being used for the alarm buffer, since this is not being streamed over the network. When bandwidth throttling is turned off, all affected codecs' quality is restored to the original configured value.
Introduction 1-4 Configuration and User Guide
Installation Detailed installation instructions can be found in the printed Quick Start Guide provided with the IP Dome. The installation process is documented using a flowchart in the Quick Installation Guide provided with the IP Dome and is also found in this manual as the Installation Process. For detailed installation instructions refer to Install and Detect the IP Dome.
Installation Installation Process Remove the camera and make note of the serial number and MAC address located on the side of the box or base of the camera. Ensure that the IP Dome is connected to the computer or network which will be used for the configuration and power on. The camera will begin its initial boot up sequence which will take approximately 1 to 2 minutes. The IP Dome will perform three attempts to obtain an IP Address from the DHCP Server.
Installation Install and Detect the IP Dome The following provides detailed information for installing and accessing the IP Dome. Installation using DHCP and Bonjour for Windows The following provides information for installing the IP Dome on your network using the Zeroconf service discovery protocol and Apple Inc.'s application discovery tool, called Bonjour.
Installation Procedure 2-2 Installing the IP Dome using DHCP Server Logs 1 Using the Quick Start Guide install and connect the IP Dome to the computer or network which will be used for the configuration and power on. The camera will begin its initial boot up sequence which will take approximately 1 to 2 minutes. 2 When using a DHCP Server the IP Dome will automatically be assigned a Network IP Address. 3 View the DHCP Server system logs and make note of the IP address assigned to the IP Dome.
Installation ActiveX Installation When using Internet Explorer to access the IP Dome the browser may need to download and install selected ActixeX plug-ins. The web browser uses the following ActiveX controls: • Sensormatic Electronics Corporation - to display live video and enable privacy zones. • Apple Quick Time - to enable audio. Depending on your browser security settings you may see a message displayed in the information bar prompting you to proceed with an automatic installation.
Installation 2-6 Configuration and User Guide
Web Configuration This section details how to configure the IP Dome using the built-in Web Configuration feature. Depending on user access you can view Live video and control the camera through PTZ controls as well as changing the settings for the camera environment. Some items supplement similar features that may be available through your controller.
Web Configuration Log in to the IP Dome Procedure 3-4 Logging in to the IP Dome 1 Refer to the Installation chapter for details on how to connect to the IP Dome on your network or computer. 2 When the IP Dome is selected Figure 3-1 the IP Dome Sign In page will be displayed. Figure 3-1 Sign in page 3 Select your preferred language from the drop-down menu in the right hand corner. The sign in page will be updated to display the selected language.
Web Configuration Administrator When an Administrator has logged in Figure 3-2 the Live Viewing screen will be displayed. An ‘admin’ account has full access to all of the cameras functions and information. The default Figure 3-2 Live Viewing Screen The options available to the Administrator are: • Live Viewing - allows access to live video and camera controls. It also allows the configuration of video, presets, patterns, scans/sequences, privacy zones, audio and camera settings.
Web Configuration Recorder When a Recorder user has logged inFigure 3-3 the Live Viewing screen will be displayed. A ‘recorder’ account has limited access to the camera functions and information. Figure 3-3 Live Viewing Logged in as Recorder The options available to the Recorder are: • Live Viewing - allows access to live video and camera controls. It also allows the configuration of video, presets, patterns, scans/sequences, privacy zones, audio and camera settings.
Web Configuration User When a User user has logged in Figure 3-4 the Live Viewing screen will be displayed. A ‘user’ account has limited access to the camera functions and information. Figure 3-4 Live Viewing Logged in as User The options available to the user are: • Live Viewing - allows access to live video and camera controls. Also allows the selection of presets, patterns, scans/sequences, audio and privacy zones.
Web Configuration Checking Camera Feed using the Live Viewing function The Live Viewing page provides a simple way to test the video inputs from the IP Dome. This Live Viewing page is not intended to be the primary way of viewing the video on the IP Dome; this should be performed using the Network Video Recording device. The Live Web Video is accessible to any authorized user.
Web Configuration • 2CIF (704) • 4CIF (640) • 4CIF (704) The default Resolution is set to 2CIF (640). 6 To adjust the volume use the slider, or the mute button. The slider bar can be moved left or right using the mouse or for fine adjustments using the left and right arrow keys on the PC keyboard. The default volume is set to 50 and the mute button will be enabled. 7 Select a different tab to exit the screen, or Logoff to exit the application.
Web Configuration Procedure 3-7 Controlling the camera via the Live Web Video pane Note Scheduled tasks, alarms and manual dome camera control will always begin when they are selected or scheduled to start. None of these camera actions have a priority over the other. If a camera action is in progress and a new action is selected or activated the previous action will stop before the new action is started. 1 Follow Procedure 3-5 Starting the Live Web Video feed.
Web Configuration Controlling the Pan-Tilt Control via Mouse Controlling the camera using the mouse will allow you to move slowly which will provide maximum accuracy. Procedure 3-8 Controlling Pan and Tilt via a mouse using the Live Web Video pane 1 Follow Procedure 3-5 Starting the Live Web Video feed. 2 Select Dome Control displayed. in the live web Video pane. The camera control overlay will be 3 Move the cursor over the center of the video pane. The Cursor Origin Mark shown in Figure 3-5.
Web Configuration 5 Select Exit to close the camera control overlay. Procedure 3-10 Selecting a Pattern via the Camera Control Overlay Note It is also possible to select a pattern using the Pattern menu, refer to Procedure 4-21 Selecting a Pattern for more information. 1 Follow Procedure 3-5 Starting the Live Web Video feed. 2 Select Dome Control displayed. 3 Select Pattern will be displayed: in the Live Web Video pane.
Web Configuration 4 Select a pattern slot number from the drop-down menu, the new pattern will be saved to this slot number. Select Define Pattern the pattern definition menu will be displayed: Note If the selected pattern slot number has been assigned to a pattern it will be replaced without warning. This also applies to any pattern that is associated with a Home Position, Alarm Action or Scheduled task. The original pattern will be replaced by the new pattern.
Web Configuration 2 Select Dome Control displayed. in the Live Web Video pane. The camera control overlay will be 3 Select Preset in the camera control overlay to open the preset menu. The preset menu will be displayed: 4 Select a preset slot number from the drop-down menu. 5 Select to run the preset. The preset will run continuously until interrupted by a camera command, pattern, scan or alarm. 6 Select Exit to close the preset menu. 7 Select Exit to close the camera control overlay.
Live Viewing Menu Video When Video is selected from the Live Viewing menu and Live Web Video has been started, (refer to Procedure 3-5 Starting the Live Web Video feed) Figure 4-6 the Video screen will be displayed. Figure 4-6 Video screen Procedure 4-14 Configuring the Video settings Note Changing the Quality, Sensitivity, Resolution or Volume settings only affects what is being displayed on the Live Viewing page.
Live Viewing Menu • Normal • Super The default Quality is set to Normal. 5 Select the Sensitivity from the drop-down menu and select the Apply button. • Normal • High The default Sensitivity is set to Normal. 6 Select the Resolution from the drop-down menu and select the Apply button. When using PAL, the resolution options are: • QVGA (320 x 240) • 1 CIF (352 x 288) • HVGA (640 x 240) • 2CIF (704 x 288) • VGA (640 x 480) • 4CIF (704 x 576) The default PAL resolution is set to 2CIF (704 x 288).
Live Viewing Menu Presets A Preset is a pre-positioned camera scene that you program for cameras installed with pan/tilt and motorized lens capability. Up to 96 presets can be programmed from the Live Viewing screen. Procedure 4-15 Adding a Preset Note This procedure is the recommended method for adding a new preset, however It is also possible to add a preset using the camera overlay control, refer to Procedure 3-13 Defining a Preset via the Camera Control Overlay.
Live Viewing Menu 4 Select Add Preset from the Presets menu. Figure 4-7 the add Preset screen will be displayed. Figure 4-7 Add Preset screen 5 Enter the Preset Name in the text box. 6 Select a Preset Slot Number from the drop-down menu. A free preset slot number will have the slot number displayed, for example, ‘12)’. If the slot number has been pre-defined, the slot number and preset name will be displayed, for example, ‘10) Main Entrance’.
Live Viewing Menu 3 Choose Select Preset from the Presets menu. Figure 4-8 the Select Preset section will be displayed. Figure 4-8 Select Preset 4 Select the pre-defined preset from the drop-down menu. 5 Select the Goto button to activate the preset. The Live Web Video pane will update to display the selected preset. The preset will run continuously until interrupted by a camera command, pattern, scan or alarm. Procedure 4-17 Editing a Preset 1 Select Presets from the Live Viewing menu.
Live Viewing Menu Using Preset as Home Position The home position runs after a designated period of dome inactivity. Select a home position if you want to keep a specific area under surveillance whenever the dome is not moving. Follow Procedure 5-6 Display Current Home Position to change the return time for the home position. Procedure 4-18 Using a Preset as a Home Position 1 Select Presets from the Live Viewing menu. 2 Choose Select Preset from the Presets menu.
Live Viewing Menu Patterns A pattern is a series of pan, tilt, zoom and focus movements which can be saved to the dome. A maximum of 16 patterns can be programmed for the IP Dome each containing up to 97 steps with an unlimited duration. Procedure 4-20 Adding a Pattern Note This procedure is the recommended method for adding a new pattern, however It is also possible to add a pattern using the camera overlay control, refer to Procedure 3-11 Add a Pattern via the Camera Control Overlay.
Live Viewing Menu 4 Enter the Pattern Name in the text box and select the Define button. The Add Pattern section will update with an Add and Cancel button. See Figure 4-11. Figure 4-11 Add Pattern with active Add and Cancel button Use the camera overlay controls to configure the required pattern settings. See Procedure 3-7 Controlling the camera via the Live Web Video pane and Procedure 3-8 Controlling Pan and Tilt via a mouse using the Live Web Video pane for further details.
Live Viewing Menu 5 The white progress bar provides a visual representation of the number of steps remaining in the pattern, this can be seen in Figure 4-12 Add Pattern with progress bar displayed. As steps are added to the pattern this progress bar will decrease. Figure 4-12 Add Pattern with progress bar displayed When the progress bar reaches the left side, no more steps will be saved for the pattern. 6 Select the Add button when you have finished.
Live Viewing Menu 2 Choose Select Pattern from the Patterns menu. Figure 4-8 the Select Pattern section will be displayed. Figure 4-13 Select Pattern 3 Select the pre-defined pattern from the drop-down menu. Note Apple Peel is a predefined pattern stored on the camera by default. This pattern slowly tilts and rotates the camera through 360 degrees starting at the ceiling line. When the IP Dome reaches the lowest tilt point it will perform three revolutions.
Live Viewing Menu 2 Select Delete Pattern from the Patterns menu button. Figure 4-14 the Delete Pattern section will be displayed. Figure 4-14 Delete Pattern 3 Select a pre-defined pattern from the drop-down menu. Note You cannot delete a pattern while it is associated with another camera function. To remove the pattern refer to the associated camera function, Clear the Current Home Position, Configuring Alarm Actions and Editing a Scheduled Task. 4 Select the Delete button.
Live Viewing Menu Scans/Sequences The following section provides information on configuring Scans and Sequences for the IP Dome. Scans A scan allows you to program left and right scan limits to automate your surveillance activities. Once these scan limits are programmed you can choose to run a smooth scan, stepped scan, or random scan. When active, the scan repeats until interrupted by a camera command, preset, pattern or alarm.
Live Viewing Menu 3 Choose Select Scan from the Scans/Sequences menu. Figure 4-16 the Select Scan screen will be displayed. Figure 4-16 Select Scan screen 4 Select the type of scan to perform from the drop-down menu: • smooth - slowly pans between the left and right scan limits, starting at the left scan limit. When the right scan limit is reached, the scan reverses. • stepped - pans slowly, pausing briefly every 10° between the left and right scan limits.
Live Viewing Menu 2 Choose Select Scan from the Scans/Sequences menu. Figure 4-16 the Select Scan screen will be displayed. 3 Select the type of scan to perform from the drop-down menu. 4 Select the Use as Home button to set the selected scan as the camera home position. Sequences A Sequence is a sequential display of multiple camera Presets. Sequences provide a methodical and effective way to monitor multiple areas of interest by switching to different Presets automatically.
Live Viewing Menu Follow Procedure 5-6 Display Current Home Position to change the return time for the home position. Procedure 4-28 Using a Sequence as a Home Position 1 Select Scans/Sequences from the Live Viewing menu. 2 Choose Select Sequence from the Scans/Sequences menu. Figure 4-17 the Select Sequence section will be displayed. 3 Select a sequence from the drop-down menu. 4 Select the Use as Home button to set the selected sequence as the camera home position.
Live Viewing Menu 2 Select Add Sequence from the Scans/Sequences menu button. Figure 4-18 the Add Sequence section will be displayed. Figure 4-19 Shortcut to Add Sequence 3 Select the Add button to open the Add Sequence screen. Refer to Procedure 5-18 Add a Sequence for information on adding a sequence, begin at step 4.
Live Viewing Menu Privacy Zones The following provides information on configuring Privacy Zones for the IP Dome. Up to 32 privacy zones can be established for the IP Dome. Note Ensure that you have the latest version of ActiveX installed. Privacy Zone Settings Privacy Zones are “masked” sections of the dome’s viewing area. These masks prevent operators of the surveillance system who do not have access to the dome password from viewing these designated zones.
Live Viewing Menu Procedure 4-31 Defining Privacy Zones 1 Select Privacy Zones from the Live Viewing page. 2 Select Add Zone from the Privacy Zones menu. Figure 4-20 the Adding a Privacy Zone screen will be displayed. Figure 4-20 Adding a Privacy Zone screen 3 Click on the dome icon, and use the camera controls to position the camera so that the area to be obscured is in the centre of the live viewing pane. See Procedure 3-7 Controlling the camera via the Live Web Video pane for further details.
Live Viewing Menu 5 Using the cursor locate the start point for the privacy zone then click and drag on the still image to define the area. As you move the cursor an outline will appear on the image which highlights the privacy zone as seen in Figure 4-21.
Live Viewing Menu 6 Release the mouse button. The selected area will turn black as seen in Figure 4-22. Figure 4-22 Privacy Zone Selected Note Areas of the Privacy Zone may be exposed during rapid pan/tilt movements of the dome. To compensate for this limitation, you may want to program the Privacy Zone to be 20 to 25% larger than the area you want to mask. Note When creating a small Privacy Zone it is recommended to use a low zoom level, preferably between 1x and 10x.
Live Viewing Menu 8 Select the Add button to save the selected privacy zone. The black rectangle will change to grey to confirm that the privacy zone has been saved. Alternatively select the Cancel button to clear the privacy zone name and selection. Figure 4-23 Privacy Zone confirmed The privacy zone will now appear on the Select Zone and Delete Zone drop-down menus. Procedure 4-32 Selecting a Privacy Zone 1 Select Privacy Zones from the Live Viewing page.
Live Viewing Menu 3 Select the pre-defined privacy zone from the drop-down menu. 4 Select the Goto button to activate the privacy zone. The Live Web Video pane will update to display the selected privacy zone. Procedure 4-33 Delete a Privacy Zone 1 Select Privacy Zones from the Live Viewing page. 2 Select Delete Zone from the Privacy Zones menu. Figure 4-25 the Delete Zone section will be displayed Figure 4-25 Delete Zone 3 Select a pre-defined zone from the drop-down menu. 4 Select the Delete button.
Live Viewing Menu 4 Select the Toggle button. If the zone is currently disabled it will be enabled. Select the Toggle button again to disable the privacy zone. Note Disabled Privacy Zones are followed with an ‘*’. 5 Repeat steps 3 and 4 to enable or disable further privacy zones.
Live Viewing Menu Stored Audio The IP Dome is capable of playing back stored audio. The dome supports one channel of bidirectional audio, streamed as uncompressed data. Audio 'frames' are time stamped to allow the synchronization of audio and video playback. This is part of the normal program stream protocol. Note Audio can only be used if a Micro SD Card has been installed. Refer to the printed Quick Start Guide for information on how to install the micro SD card.
Live Viewing Menu 2 Select Add Audio from the Stored Audio menu. Figure 4-27 the Add Audio screen will be displayed. Figure 4-27 Add Audio screen Note If the Browse and Upload buttons are unavailable, an example is shown in Figure 4-28, the maximum number of audio files have been uploaded. It will be necessary to delete an existing audio file before uploading a new one. Follow Procedure 4-37 Deleting Audio then return to this procedure.
Live Viewing Menu 3 Select the Browse button. The Choose file dialog will be displayed, navigate to the location where the audio file has been saved. Select the audio file then select the Open button. Note The audio filename cannot contain spaces. An ‘Invalid item name’ error message will be displayed. 4 Select the Upload button. You will be prompted to confirm that you would like to upload the audio file. Select the OK button to confirm or the Cancel button to stop the upload.
Live Viewing Menu 4 Select the Delete button to delete the audio clip. You will be prompted to confirm the deletion. Select the OK button to confirm or the Cancel button to stop the deletion.
Live Viewing Menu Camera Adjust This section describes how to adjust the camera’s settings. When Camera Adjust is selected from the Live Viewing menu. Figure 4-31 the Camera Adjust screen will be displayed.
Live Viewing Menu 2 Select EIS/WDR from the Camera Adjust menu. Figure 4-32 the EIS/WDR section will be displayed. Figure 4-32 EIS/WDR 3 In the EIS/WDR section select a setting: • Off - turns off the image stabilization and allows WDR to be selected) • 5Hz - designed to stabilize the dome when unwanted dome movements are at 5Hz) • 10Hz - designed to stabilize the dome when unwanted dome movements are at 10Hz) The default setting is ‘off’.
Live Viewing Menu Procedure 4-39 Configuring Wide Dynamic Range 1 Select Camera Adjust from the Live Viewing menu. 2 Select EIS/WDR from the Camera Adjust menu. Figure 4-32 the EIS/WDR section will be displayed. 3 Select Off in the EIS Setting. Note When Electronic Image Stabilization is enabled, the WDR feature cannot be enabled. 4 Select the check box in the Wide Dynamic Range section to enable or disable the function. The default setting is disabled.
Live Viewing Menu 2 Select Auto Focus/Iris from the Camera Adjust menu. Figure 4-33 the Auto Focus/Iris section will be displayed. Figure 4-33 Auto Focus/Iris 3 Select the Auto Iris check box to enable or disable the Auto Iris function. The default setting is enabled. Procedure 4-41 Configuring the Auto Focus setting 1 Select Camera Adjust from the Live Viewing menu. 2 Select Auto Focus/Iris from the Camera Adjust menu.
Live Viewing Menu quality, reduce the workload for down stream image compression techniques and also save storage space on a network video recorder. The effectiveness of de-interlacing is clearly visible on Figure 4-34 and Figure 4-35. In Figure 4-34 de-interlacing has been disabled, this results in an unclear image. In Figure 4-35 de-interlacing has been enabled and a clear image is visible.
Live Viewing Menu 2 Select De-Interlacing from the Camera Adjust menu. Figure 4-36 the De-Interlacing section will be displayed. Figure 4-36 De-Interlacing section 3 Select the De-Interlacing check box to enable or disable the De-Interlacing function. The default setting is enabled. Note It is recommended that de-interlacing should always be enabled on the IP Dome. Automatic White Balance White balance is normally compensated for by the automatic white balance gain control.
Live Viewing Menu Figure 4-37 Automatic White Balance Procedure 4-43 Configuring the Automatic White Balance 1 Select Camera Adjust from the Live Viewing menu.
Live Viewing Menu 2 Select White Balance from the Camera Adjust menu. Figure 4-38 the White Balance section will be displayed. Figure 4-38 White Balance 3 Select the Auto White Balance check box to enable or disable the White Balance function. The default setting is enabled. Note When Automatic White Balance is disabled, the camera uses the red and blue setting values to control the white balance. See Procedure 4-44 Configuring the Red and Blue Settings.
Live Viewing Menu 3 Disable the White Balance function by selecting the check box, Figure 4-39 the Red and Blue balance section will be displayed. Note When Automatic White Balance is first switched from disabled to enabled, the red and blue values displayed are based on the current feedback from the camera. Figure 4-39 Red and Blue balance 4 Use the slider to change the Red and Blue balance.
Live Viewing Menu Zoom tracing is the process of maintaining auto focus as the zoom lens moves in or out.
Live Viewing Menu 2 Select IR/Day Night Mode from the Camera Adjust menu. Figure 4-40 the IR/Day Night Mode section will be displayed. Figure 4-40 IR/Day Night Mode section 3 In the IR/DayNight Mode section, use the DayNight Mode drop-down menu to select: • visible - no special lighting • 850nm • 950nm The default setting is ‘visible’. Procedure 4-46 Configuring the Day/Night Mode setting 1 Select Camera Adjust from the Live Viewing menu. 2 Select IR/Day Night Mode from the Camera Adjust menu.
Live Viewing Menu The default setting is ‘automid’. Note If EIS is enabled autolow and automid will be unavailable. Note If AGC/Shutter Setting is set to openshutter autohigh will be unavailable. North Position Direction Indicators permit you to understand the approximate pointing position of the dome to an established reference point. This reference point is called “North” and may correspond to magnetic north (if it is known) or some other landmark or fixture.
Live Viewing Menu 4 Use Procedure 3-7 Controlling the camera via the Live Web Video pane or/and Procedure 3-8 Controlling Pan and Tilt via a mouse using the Live Web Video pane to locate the desired north position. 5 Select the Set button to confirm the North Position. Shutter Limit The Shutter Limit value sets the video update time in fractions of a second. Depending on the lighting conditions, the video information may be updated more frequently, but no slower than the limit set.
Live Viewing Menu • AGC off - produces the cleanest image with the least noise but is not suitable for low light scenes. • AGC on - good for low light scenes but slight noise will be visible. • openshutter - best for low light scenes but will show a lot of noise. The default setting is ‘openshutter’. Note If you require “Real Time” video this feature must be turned off to ensure that the resulting video quality is acceptable for prosecution purposes.
Live Viewing Menu 4 In the MAX Gain section use the slider to select the maximum gain. Selecting a lower value will give a cleaner image but reduced low light performance, a higher value will give better low light performance but a more noise will be visible. The slider bar can be moved left or right using the mouse or for fine adjustments using the left and right arrow keys on the PC keyboard.
Live Viewing Menu 3 When ‘openshutter’ is selected from the AGC/Shutter Setting drop-down menu the MAX Gain and Shutter Speed section will be displayed as in Figure 4-44. Figure 4-44 Shutter Setting at openshutter 4 In the MAX Gain section use the slider to select the maximum gain. Selecting a lower value will give a cleaner image but reduced low light performance, a higher value will give better low light performance but a more noise will be visible.
Live Viewing Menu Selecting a fast shutter speed will give the least amount of artifacts but reduced low light performance, a slower shutter speed will give better low light performance but more artifacts will be visible. 6 The default setting is 1/3 (PAL) and 1/4 (NTSC). Picture Adjust brightness, contrast, hue and saturation of the image displayed in the Live Web Video pane. Procedure 4-51 Changing the Brightness, Contrast, Hue and Saturation 1 Follow Procedure 3-5 Starting the Live Web Video feed.
Live Viewing Menu 5 Use the slider to change the Contrast. Contrast changes shades between the lightest and darkest areas of the Live Web Video display. The values range from 0 to 255. The image displayed in the Live Web Video pane will update to display the changes. The default setting is 128. 6 Use the slider to change the Hue. The values range from -128 to 127. The image displayed in the Live Web Video pane will update to display the changes. The default setting is 0.
Live Viewing Menu 4-46 Configuration and User Guide
Camera Menu In this section you can adjust the camera settings, including PTZ configuration, Overlay Settings, Alarms, Video and Audio. PTZ Configuration When PTZ Configuration is selected from the Camera menu. Figure 5-1the PTZ Configuration screen will be displayed.
Camera Menu Automatic Flip Use the automatic (proportional) “flip” feature when you need to track someone who walks directly under the dome and continues on the other side. You start the flip by moving the tilt control to its lower limit and holding for a brief period. When the flip engages, the dome automatically rotates 180°. You may then continue to track the person as long as the tilt control stays in its lower limit. Once the tilt control is released, the dome resumes normal operation.
Camera Menu 35X Camera Dome The IP Dome 35X camera dome includes a 35X optical zoom camera with 12X digital zoom capability. The maximum possible zoom is 420X. The following example explains how 35X camera zoom stop settings work. The default camera settings are 52X for the first zoom stop setting and 140X for the maximum zoom setting. If the current zoom level is less than 52X, pressing Zoom In continuously causes the zoom to stop at 52X.
Camera Menu Return Settings When calling a Preset, the dome adopts the settings (both only available on 35X cameras) uniquely created for that Preset. When an operator moves the dome from its Preset position, the dome can return to global settings only if programmed to do so through the Return to Auto screen. Return to Auto Focus/Auto Iris The automatic focus will keep the scene displayed in focus and will make the necessary changes to ensure this is maintained.
Camera Menu If a home position has been set on the camera the information will be displayed. You also have the option to clear the current home position. Procedure 5-6 Display Current Home Position 1 Select PTZ Configuration from the Camera menu. 2 If a home position has been set the details will be displayed in the Current Home Position section. If no home position has been set the text boxes will be empty. 3 Use the slider bar to select the Return Time in minutes.
Camera Menu Overlay Settings Use this section to display dome status information, enable or disable the display of all name information and display direction information about where the dome is pointing. When Overlay Settings is selected from the Camera menu. Figure 5-1 the Overlay Settings screen will be displayed. Figure 5-1 Overlay Settings screen Camera Name Choose whether or not to display the camera name in the on-screen display.
Camera Menu 2 In the Camera Name section select the Display Camera Name to enable or disable the camera name display. The default setting is disabled. The Camera Name is defined in Procedure 6-51 Setting the Camera Name. 3 Once you have chosen your settings, to save the changes select the Apply button or to cancel the changes select the Refresh button at the bottom of the page. Camera Status You can choose to display the status of the zoom setting, auto iris, and auto focus.
Camera Menu indicator is relative to the “virtual horizon” of 0° tilt. Figure 5-2 illustrates the locations of the Direction Indicators on the display. Figure 5-2 Screen locations for Direction Indicators In this example, the current pointing position is 60° from North. The tilt elevation is 12° above the virtual horizon. Panning to the left points the dome towards the Northeast. Panning to the right points the dome towards the East.
Camera Menu Figure 5-3 Examples of text attributes Procedure 5-12 Configuring the attributes of displayed text 1 Select Overlay Settings from the Camera menu. 2 In the Text Attributes section select the check boxes to enable or disable the characteristics of the displayed text. Choose whether to display text as translucent (slightly clear) or solid, with or without outlines. • Character Outline • Translucent The default setting for these functions is disabled.
Camera Menu Areas The following provides information on configuring Areas. Areas List Areas allow sections within the field of view to be labeled. These labels may then be turned on within the Overlay Settings option. Areas may not overlap. The zoom level affects the size areas may appear. You may program from two to 16 areas. When Areas is selected from the Camera menu. Figure 5-4 the Areas screen will be displayed.
Camera Menu Figure 5-5 An example of areas The ending point of one area is the starting point for the next area. The ending point of the last area cannot go past the starting point of the first area. In this example, the area that includes the vending machines cannot extend past the starting point of the area that includes the emergency exit. If your controller supports areas, these are separate from the areas you can program with the dome.
Camera Menu 7 Once you have chosen your settings, to save the changes select the Apply button or to cancel the changes select the Refresh button at the bottom of the page. Procedure 5-14 Editing Areas 1 Select Areas from the Camera menu. 2 Select the Edit icon of the area you would like to change. 3 Make your changes. 4 Once you have chosen your settings, to save the changes select the Apply button or to cancel the changes select the Refresh button at the bottom of the page.
Camera Menu Alarms The camera can be commanded to carry out a specified operation when a alarm is triggered. The following provides information on setting Alarms. Note Scheduled tasks, alarms and manual dome camera control will always begin when they are selected or scheduled to start. None of these camera actions have a priority over the other. If a camera action is in progress and a new action is selected or activated the previous action will stop before the new action is started.
Camera Menu Alarms can be processed internally by the dome, externally by the controller, or both. If the changes in input state are sent to the host controller, the host actions have higher priority than the associated dome actions. Note An active internal alarm only resets when the input state changes to “normal.” A manual reset is not available. Note Enabling Email or FTP of video or pictures requires a MJPEG video stream.
Camera Menu • Parameter - only selectable if an action has been selected. Choose the preset, pattern, sequence or scan to run when the alarm has been triggered. • Output – check box to activate the digital output as a action. For example, this digital output could be linked to a electrical device, i.e. a security light or siren. • Email – check box to send an email to the user configured in STMP Settings. Refer to Procedure 6-38 Configuring the Email Settings if SMTP settings have not been defined.
Camera Menu Add Sequence The following provides information on configuring sequences. Sequence Names A Sequence is a sequential display of multiple camera Presets. Sequences provide a methodical and effective way to monitor multiple areas of interest by switching to different Presets automatically. Sequences are created by identifying Preset views to include in the Sequence and specifying a dwell time that controls how long each Preset remains on-screen before switching to another Preset.
Camera Menu 3 Select the Add Sequence button. Figure 5-10 the Add Sequence Screen will appear. Figure 5-10 Add Sequence Screen 4 Enter a Sequence Name in the text box. 5 Select a preset from the Preset Name drop-down menu. 6 Enter a Dwell Time in seconds in the text box. The values range from 5 to 600 seconds. 7 Select the Add button. The preset is now listed as part of the sequence. 8 Repeat steps 5 and 6 to add further presets to the sequence. Note Up to 16 presets can be added to a sequence.
Camera Menu 2 Select the Edit icon of the sequence you would like to edit. Figure 5-11 the Sequence Details screen will be displayed which shows details of the presets included within the sequence. Figure 5-11 Sequence Details screen 3 You can now make any necessary changes to the sequence. • To edit an existing preset select the edit icon of the preset you would like to edit. You are now able to select a different Preset Name and change the Dwell Time.
Camera Menu Scheduled Tasks Schedule tasks to include specific situations or events; you can set up a regular schedule or a custom schedule. For example, you could set the same schedule for all cameras, every day of the week, or set custom schedules for weekday, weekend, and holiday operation for each camera. Note Changing the schedule can affect the recording’s duration. Use defaults when possible.
Camera Menu 2 Select the New Task button. Figure 5-13 the Schedule/Edit Task screen will be displayed. Figure 5-13 Schedule/Edit a Task 3 Enter a Name for the task in the text box. 4 Select the start time of the task, use the 24hr clock: hh:mm. 5 Select the task frequency, select from every day, week days or days of month. If week days has been selected you will be required to choose the days on which days the task will run. Select the check box beside the day to add that day to the task frequency.
Camera Menu 2 Select the Delete icon of the scheduled task you would like to delete. 3 You will be prompted to confirm the deletion. Select the OK button to confirm or the Cancel button to stop the deletion.
Camera Menu Video Video allows you to select the video preferences for ACC Frame Rate, Alarm Video Settings and RTSP Timeout. When Video is selected from the Camera menu. Figure 5-14 the Video screen will be displayed. Figure 5-14 Video screen Procedure 5-24 Configuring the Web GUI ACC Frame Rate 1 Select Video from the Camera menu. 2 In the Web GUI ACC Frame Rate section select the Default ACC Frame Rate (ips) from the drop-down menu. The values range from 1 to 25 (PAL) and 1 to 30 (NTSC).
Camera Menu 4 Select the Resolution from the drop-down menu. When using PAL, the resolution options are: • QVGA (320 x 240) • 1 CIF (352 x 288) • HVGA (640 x 240) • 2CIF (704 x 288) • VGA (640 x 480) • 4CIF (704 x 576) • D1 (720x576) The default PAL resolution is set to 2CIF (704 x 288).
Camera Menu Audio Audio allows you to configure the Audio Input and Audio Out. When Audio is selected from the Camera menu. Figure 5-15 the Audio screen will be displayed. Figure 5-15 Audio screen Procedure 5-27 Configuring Audio Input 1 Select Audio from the Camera menu. 2 In the Audio Input section use the check box to enable or disable the Input enable function. The default setting is disabled. 3 Use the slider to select the Input gain.
Camera Menu 3 Use the slider to select the Output Volume. The slider bar can be moved left or right using the mouse or for fine adjustments using the left and right arrow keys on the PC keyboard. The values range from 1 to 100. The default volume is set to 50. 4 Once you have made your changes, use the Apply or Refresh button at the bottom of the page to either save or cancel the settings.
Camera Menu 5-26 Configuration and User Guide
Networking Menu Date Time Set the camera’s time and date format. When Date Time is selected from the Networking menu. Figure 6-16 the Date Time screen will be displayed. Figure 6-16 Date Time screen Date Time Format Set the format of the date and time. Procedure 6-29 Configuring the Time format 24-Hour 1 Select Date Time from the Networking menu. 2 In the Date Time Format section, check the Camera Time. If it is incorrect it can be altered using Procedure 6-32 Setting the Camera Time.
Networking Menu 4 Once you have chosen your settings, to save the changes select the Apply button or to cancel the changes select the Refresh button at the bottom of the page. Note If either Synchronize with computer or Synchronize with NTP Server have been selected in the Setting camera time section it will be necessary to confirm the change settings and reboot the camera. You will have to log back in to the IP Dome when it restarts, Follow Procedure 3-4 Logging in to the IP Dome.
Networking Menu • Set manually • Synchronize with computer. • Synchronize with NTP Server. The default is ‘Set manually’ 3 If you select Set manually: • Enter the date into the text box • Enter the time into the text box. 4 If you select Synchronize with computer the date and time will be entered automatically. 5 If you select Synchronize with NTP Server, enter the NTP Server Name in the text box.
Networking Menu TCP/IP Configure the DHCP, the IP address and the DNS in this section. When TCP/IP is selected from the Networking menu. Figure 6-17 the TCP/IP screen will be displayed. Figure 6-17 TCP/IP screen DHCP Configuration When a DHCP server is running on the network enabling DHCP on the camera will allow an IP address to be automatically assigned to the camera. DHCP on the IP Dome is defaulted to enabled.
Networking Menu 3 Enter the Subnet Mask in the text box. 4 Enter the Default Router address in the text box. 5 Once you have chosen your settings, to save the changes select the Apply button or to cancel the changes select the Refresh button at the bottom of the page. Note If you are using Bonjour for Windows a known limitation is that it is not always able to maintain an up-to-date list of IP devices.
Networking Menu Users In this section you are able to add and delete user accounts for the IP Dome. There are three levels of access: Admin, Recorder, and User. Refer to User Accounts for more information on the access rights of each. When Users is selected from the Networking menu. Figure 6-18 the Users screen will be displayed. Figure 6-18 Users Administration screen User Administration In the User Administration section you can Add, edit or delete user accounts.
Networking Menu • Recorder – has limited access to the camera and settings. • User – can view Information and Live Viewing menus. 5 Enter a Password in the text box. The password is case sensitive and can contain alphanumeric characters with a length of between 4 and 20 characters. 6 Enter the same password in the Confirm Password text box. 7 Select the Add User button to save the account. The User Administration screen will be displayed.
Networking Menu SMTP Settings Configure the SMTP settings to send e-mail alerts in this section. When SMTP Settings is selected from the Networking menu. Figure 6-20 the SMTP Settings screen will be displayed. Figure 6-20 SMTP Settings screen Email Settings Set up the mail server which will be used when sending details of triggered alarms. Note SMTP must be configured to enable email alerts when using alarms. Procedure 6-38 Configuring the Email Settings 1 Select SMTP Settings from the Networking menu.
Networking Menu Email Test Check that your SMTP settings are functioning correctly. Procedure 6-39 Testing the SMTP configuration 1 Select SMTP Settings from the Networking menu. When Procedure 6-38 Configuring the Email Settings has been followed the Email Test section will be visible. 2 In the Email Test section select the Test button. A test email will be sent to the email address specified in Email Settings. It will contain the following message.
Networking Menu FTP Settings Configure the FTP settings for the FTP server in this section. When FTP Settings is selected from the Networking menu. Figure 6-17 the FTP Settings screen will be displayed. Figure 6-21 FTP Settings screen FTP Settings Set the Remote Settings and Authentication for the FTP Server. Note FTP must be configured to enable FTP alerts when using alarms. Procedure 6-40 Configuring Remote Settings and Authentication 1 Select FTP Settings from the Networking menu.
Networking Menu Date: Time: Receipt of this text file proves that the ftp settings are correct for this camera.
Networking Menu Firewall Configure the Basic Filtering and Address Filtering for the Firewall. When Firewall is selected from the Networking menu. Figure 6-22 the Firewall screen will be displayed. Figure 6-22 Firewall Settings screen Firewall Set the Basic Filtering and Address Filtering for the Firewall here. Procedure 6-42 Configuring Basic Filtering 1 Select Firewall from the Networking menu. 2 Select the ICMP Blocking check box to enable or disable this function. The default setting is disabled.
Networking Menu 2 Select the Address Filtering check box to enable or disable this function. The default setting is disabled. If Address Filtering is enabled. Figure 6-23 the Address List section will be displayed. Figure 6-23 Address List section 3 Enter the IP or MAC Address in the text box. 4 Select the Add button to accept the entry. 5 To enter another IP or MAC Address repeat steps 3 and 4.
Networking Menu Maintenance Backup, restore, upgrade the server, perform a reboot or return to factory defaults from this section. You are also able to upload a HTTPS certificate. When Maintenance is selected from the Networking menu. Figure 6-24 the Maintenance screen will be displayed. Figure 6-24 Maintenance screen Procedure 6-44 Backup Camera Settings The configuration settings of the IP Dome can be backed up to a data file.
Networking Menu 1 Select Maintenance from the Networking menu. 2 In the Backup Camera section select the Backup button. The File Download dialog will be displayed and you will be prompted to save the backup file to disk. 3 Select the Save button, the Save As dialog will be displayed. If required enter a new File Name for the backup file in the text box. Note The filename must end with’.bin’. 4 Browse to the location where you would like to save the backup file.
Networking Menu HTTPS Certificate The IP Dome has the ability to use a HTTPS Certificate. Procedure 6-47 Add a HTTPS Certificate 1 Select Maintenance from the Networking menu. 2 In the HTTPS Certificate section select the Browse button. The Choose file dialog will be displayed, navigate to the location where the HTTPS Certificate has been saved. Note Note the certificate needs to match the camera ‘host name’. 3 Select the file you would like to load to the camera then select the Open button.
Networking Menu 6 Follow Procedure 3-4 Logging in to the IP Dome to confirm that the camera has been restored to the factory default settings. Procedure 6-50 Reboot the Camera Will perform a reboot of the camera. 1 Select Maintenance from the Networking menu. 2 In the Administrative Options section select the Reboot button. You will be prompted to confirm that you would like to reboot the camera. 3 Select the OK button to confirm the reboot or select the Cancel button to stop the reboot.
Networking Menu Advanced Advanced settings allows you to set the camera name, bandwidth throttling, session timeout and Bonjour settings. When Advanced is selected from the Networking menu. Figure 6-25 the Advanced screen will be displayed. Figure 6-25 Advanced screen Procedure 6-51 Setting the Camera Name The camera friendly name will be shown on the VideoEdge® banner and on the on-screen display (OSD) if the option is selected. 1 Select Advanced from the Networking menu.
Networking Menu 4 The VideoEdge® banner will update to display the camera friendly name as seen in Figure 626. Figure 6-26 Camera Friendly Name displayed in VideoEdge® banner Bandwidth Throttling Set the bandwidth throttling for the IP Dome. Refer to Bandwidth Throttling for more information. Procedure 6-52 Set Bandwidth Throttling 1 Select Advanced from the Networking menu. 2 Use the check box to enable or disable the bandwidth throttling function. The default setting is disabled.
Networking Menu • IP address • Host name • Domain name • Friendly name • AD Defined Custom Data: • Camera model • Camera serial number • MAC address • VideoEdge API version • VideoEdge URL • IDP port. Zero Configuration Networking Zero configuration networking (or Zeroconf) is a set of techniques for automatically creating IP networks. Apple's Bonjour protocol is one of the most common implementations of Zeroconf. Zeroconf will provide: • Address assignment • Name resolution • Service discovery.
Networking Menu • _ntlx-video._tcp Procedure 6-54 Enable or Disable Bonjour Allows IP Dome to be located on the network using Bonjour. 1 Select Advanced from the Networking menu. 2 In the Bonjour section use the check box to enable or disable the Bonjour function. The default setting is enabled. Note It is recommended to keep Bonjour enabled. 3 Once you have chosen your settings, to save the changes select the Apply button or to cancel the changes select the Refresh button at the bottom of the page.
Networking Menu 6-22 Configuration and User Guide
Information Menu In this section information can be obtained on the camera, the configured settings, its physical state and any faults that have been found. It is also possible to change your password. Model When Information is selected. Figure 7-27 the Model Information screen will be displayed.
Information Menu Statistics When Statistics is selected from the Information menu. Figure 7-28 the Statistics screen will be displayed.
Information Menu • Zoom In Select the Refresh button to refresh the page for the most up-to-date information.
Information Menu Environmental When Environmental is selected from the Information menu. Figure 7-29 the Environmental screen will be displayed Figure 7-29 Environmental screen Readings will provide information on the following: • Internal Temperature • Humidity • Blower 1 • Blower 2 • Heater • Firmware Version Select the Refresh button to refresh the page for the most up-to-date information.
Information Menu System Log When System Log is selected from the Information menu. Figure 7-30 the System Log screen will be displayed Figure 7-30 System Log screen The system log gives the most recent messages from the unix /var/log/messages file. Information will include the following: • Informational messages about system behavior such as process startup/shutdown. • Warnings about recoverable problems that processes encounter.
Information Menu Boot Log When Boot Log is selected from the Information menu. Figure 7-31 the Boot Log screen will be displayed. Figure 7-31 Boot Log screen The Boot log is a log of the Linux operating system boot processes and will only be useful to AD engineers who require additional information on the device. Procedure 7-58 Update Boot Log Select the Refresh button to refresh the page for the most up-to-date information.
Information Menu Current Faults When Current Faults is selected from the Information menu. Figure 7-32 the Current Faults screen will be displayed. Figure 7-32 Current Faults screen with no faults displayed The Fault Table will display information on any faults that your camera is currently experiencing. • No - details the fault index. • Fault - a description of the fault. • Created On - the time and date when the fault occurred.
Information Menu Fault Details DIOM (Digital Input Output Monitor) Faults The following faults can be raised by the DIOM component: • DigitalAlarmInForce • DigitalRaiseInputAlarm1 • DigitalRaiseInputAlarm2 • DigitalRaiseInputAlarm3 • DigitalRaiseInputAlarm4 ENVM (Environmental Monitor) Faults If an environmental card is used the following faults can be raised by the ENVM component: • BlowerConditionFaulty (Error)- the blower condition may be GOOD or FAIL.
Information Menu Change Password When Change Password is selected from the Information menu. Figure 7-34 the Change Password screen will be displayed. Figure 7-34 Change Password screen Procedure 7-60 Changing an existing password 1 Select Change Password from the Information menu. 2 Select your username from the Name drop-down menu. 3 Enter your Current Password in the text box. 4 Enter your New Password in the text box.
Information Menu 7-10 Configuration and User Guide
Camera Recovery The IP Dome has a built in recovery process which will allow you to upload the latest firmware if the camera is unable to restart. If the camera encounters three unsuccessful restarts in a row it will automatically enter the Camera Recovery section. When this occurs Figure 8-35 the Camera Recovery screen will be displayed. Figure 8-35 Camera Recovery screen The IP Dome can be recovered using firmware provided by American Dynamics or rebooted using the Main System boot files.
4 When the process is complete. The camera will begin its initial boot up sequence which will take approximately 1 to 2 minutes. 5 Follow Procedure 3-4 Logging in to the IP Dome to confirm that the camera has been returned to the factory default settings. Procedure 8-62 Retry Main System Boot This procedure will maintain all current camera settings including the IP address and all user accounts and passwords. 1 On the Camera Recovery screen in the Retry Main System Boot section select the Reboot button.
Physical Factory Reset The following procedure restores all settings on the IP Dome including the IP address and all user accounts and passwords to the factory default settings. Warning 24VAC are accessible on the Environmental Card. Procedure 8-63 Physical Factory Reset MUST be performed by an Installer. Procedure 8-63 Physical Factory Reset 1 Remove power from the camera. 2 Remove the bubble. Refer to the printed Quick Start Guide and follow the directions in reverse to remove the bubble.
6 Locate the physical reset connector stored on the base of the camera. Refer to Figure 8-36. If there is no physical reset connector, replace the camera into the mount and contact Technical Support. 7 Attach the physical reset connector to the environmental connector on the base of the camera. Refer to Figure 8-36. 8 Replace the camera into the mount. Tighten the screws. 9 Reapply power to the camera. The camera will begin its initial boot up sequence which will take approximately 1 to 2 minutes.
Technical specification This section details the environmental and operating specifications of the IP Dome. Technical Specifications Category Power Specification Supply voltage Details 12Vdc, PoE (Indoor) 12.95W max PoE (Indoor) 802.3af compliant, 12.
Technical specification Camera Specifications 35x 22x Horizontal Resolution 540 Lines 470 Lines Imager Interline transfer 1/4-inch CCD array Interline transfer 1/4-inch CCD array Scanning System 2:1 interface 2:1 interface Wide Dynamic Range, EIS, Day/Night Yes No tS/N Ratio >50 dB (typical) >50 dB (typical) Minimum Illumination (20IRE, AGC) 0.24 lux (Color); 0.028 lux 0.3 lux (Color) (Color with 1/4 sec open shutter) 0.02 lux (Color with 1/4 sec open shutter) 0.
Technical specification Compression Category Video Compression Details MJPEG up to 30/25 ips in all resolutions MJPEG4 up to 30/25 ips in all resolutions ACC up to 30/25 ips in all resolutions H.264 Resolutions 704x576 - 320x240 Audio Compression PCM G711 A G711 U CODEC Combinations The following table shows single or dual video streams scenarios that are supported at the frame rates specified.
Technical specification WebGUI, whereas ‘ACC’ is an ACC stream used as a Live or Recording stream via the Network Video Recording device.
Technical specification Certification and Regulations Category Safety Specification UL Details Indoor*: UL60950-1 / CSA C22.2 No.60950-22 Outdoor**: UL60950-1 and UL 60950-22 / CSA C22.2 No.
Technical specification 9-6 Configuration and User Guide
Appendix 10: User Account Privileges Camera Menu Admin Recorder User X X X Video X X X Presets X X X Pattern X X X Scans/Sequences X X X Privacy Zones X X X Stored Audio X X X Camera Adjust X X - X X - PTZ Configuration X X - Overlay Settings X - - Areas X - - Alarms X - - Add Sequence X X - Live Viewing Menu Camera Menu Scheduled Tasks X - - Video X - - Audio X - - X - - Date Time X - - TCP/IP X - - Users X - - SMTP Sett
User Account Privileges 10-2 Configuration and User Guide
Appendix 11: Site Maps The site maps for the built in web configuration pages are detailed on the following pages. These have been divided into four sections using the main menu camera headings.
Site Maps Live Viewing Site Map Live Viewing Menu Video Quality Sensitivity Resolution Volume Presets Select Preset Delete Preset Add Preset Patterns Select Pattern Delete Pattern Add Pattern Scans/Sequences Select Scan Scan Limits Select Sequence Delete Sequence Add Sequence Privacy Zones Select Zone Delete Zone Add Zone Toggle Zone Stored Audio Select Audio Delete Audio Add Audio Camera Adjust EIS/WDR Auto Focus/Iris De-Interlacing White Balance IR/Day Night Mode North Position Shutter Limi
Site Maps Camera Site Map Camera Menu PTZ Configuration Automatic Flip Zoom Stops Freeze Frame Return Settings Current Home Position Overlay Settings Camera Name Camera Status Dome Names Time/Direction Indicators Text Attributes Areas Areas List Alarms Alarm Actions Add Sequence Sequence Names Scheduled Tasks Task Details Video Web GUI ACC Frame Rate Alarm Video Settings RTSP Timeout Audio Audio Input Audio Out 11-3
Site Maps Networking Site Map Networking Menu Date Time Date Time Format Time Zone Setting Camera Time TCP/IP DHCP Configuration IP Address Configuration DNS Configuration Users User Administration SMTP Settings Email Settings FTP Settings Remote Settings and Authentication FTP Test Firewall Basic Filtering Address Filtering Maintenance Backup Camera Settings Restore Camera Settings Upgrade Server HTPS Certificate Administrative Options Advanced Camera Name Bandwidth Throttling Session Timeo
Site Maps Information Site Map Information Menu Model Information Statistics General Information PTZ Summary Environmental Readings System Log View Log File Boot Log View Log File Current Faults View Fault Table Change Password Details 11-5
Site Maps 11-6 Configuration and User Guide
END USER LICENSE AGREEMENT IMPORTANT - READ CAREFULLY: THIS END-USER LICENSE AGREEMENT ("EULA") IS A LEGAL AGREEMENT BETWEEN YOU ("LICENSEE"), AND SENSORMATIC ELECTRONICS CORPORATION ("TYCO") FOR THE TYCO SOFTWARE ACCOMPANYING THIS EULA, WHICH INCLUDES COMPUTER SOFTWARE AND MAY INCLUDE MEDIA, PRINTED MATERIALS, AND "ON-LINE" OR ELECTRONIC DOCUMENTATION (COLLECTIVELY, THE "SOFTWARE PRODUCT"). BY INSTALLING, COPYING, OR OTHERWISE USING THE SOFTWARE PRODUCT, YOU AGREE TO BE BOUND BY THE TERMS OF THIS EULA.
e.Subsequent EULA. Tyco may also supersede this EULA with a subsequent EULA pursuant to providing you with any future component, release, upgrade, or other modification or addition to the SOFTWARE PRODUCT. Similarly, to the extent that the terms of this EULA conflict with any prior EULA or other agreement between you and Tyco regarding the SOFTWARE PRODUCT, the terms of this EULA shall prevail. f. Incorporation of "Open Source" and other Third Party software.
10. EXCLUSION OF OTHER DAMAGES. UNDER NO CIRCUMSTANCES SHALL TYCO OR ANY OF ITS RESELLERS OR LICENSORS BE LIABLE FOR ANY OF THE FOLLOWING: (I) THIRD PARTY CLAIMS; (II) LOSS OR DAMAGE TO ANY SYSTEMS, RECORDS OR DATA, OR LIABILITIES RELATED TO A VIOLATION OF AN INDIVIDUAL'S PRIVACY RIGHTS; OR (III) INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL, PUNITIVE, RELIANCE, OR COVER DAMAGES (INCLUDING LOST PROFITS AND LOST SAVINGS), IN EACH CASE EVEN IF TYCO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 10.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.] Preamble The licenses for most software are designed to take away your freedom to share and change it.
"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
12-10 Configuration and User Guide
A D Advanced Features Web Configuration 1-3 AGC 4-40 Alarm Actions 5-10, 5-13 Alarms 5-13 Areas 5-10 Areas List 5-10 Audio 4-24 Automatic Flip 5-1 Automatic White Balance 4-28 Date Time 6-1 Date Time Format 6-1 Dome Names 5-7 B Bandwidth Throttling 1-2 C Camera Adjust 4-28 Camera Feeds 3-6 Camera Menu Alarm Actions 5-10, 5-13 Alarms 5-13 Areas 5-10 Audio 4-24 Automatic Flip 5-1 Automatic White Balance 4-28 Camera Name 5-6 Camera Status 5-7 Dome Names 5-7 Freeze Frame 5-3 Infra Red Features 4-36 Overlay
Networking Menu Date Time 6-1 Date Time Format 6-1 Email Settings 6-8 Setting Camera Time 6-2 SMTP Settings 6-8 TCP/IP 6-4 Test 6-9 User Administration 6-6 Users 6-6 O Overlay Settings 5-6 Overview 1-1 P Patterns 4-7 Preset definition 4-3 Presets 4-3 Privacy Zone Settings 4-17 Privacy Zones 4-17 PTZ Configuration 5-1 Users 6-6 V Video 4-1 Video Loss Detection 1-2 W WDR 4-29 Web Configuration 1-3 Camera Feeds 3-6 Controlling cameras via Live Video 3-7 Log in 3-2 Wide Dynamic Range 4-29 Z Zoom Stops 5-2
