Installation & Operating Instructions HP24 Series HP12 Series ungerglobal.
Table of Contents Introduction............................................................................................... 3 Safety Information.................................................................................. 4 General Information........................................................................... 4-5 Getting to Know your nLite HydroPowerTM System................... 6 System Overview.................................................................................
Installation & Operating Instructions Introduction Thank you for choosing nLite HydroPowerTM for your pure water needs. You have chosen a high quality product backed by Unger’s 100% customer satisfaction guarantee. When used as intended, the nLite HydroPower unit will produce zero TDS pure water for site glass cleaning. The production of pure water, through deionization, is based on the principal of ion exchange. In this process, the minerals responsible for producing spotting are removed from the water.
Installation & Operating Instructions Safety Information General: Please observe applicable rules and regulations, including all accident prevention procedures. Unger is not liable for damage to application areas, plumbing system components or persons. The window cleaning contractor should strictly adhere to all applicable local, state/provincial and federal labor laws and safety codes and standards. Ensure work area has sufficient water drainage. Turn off feed water supply when not in use.
Installation & Operating Instructions General hazards associated with the use of waterfed wash pole and deionization equipment1: • Read and follow ANSI Standard IWCA 1-14.1 (Window Cleaning Safety). • Trip hazard to the general public when using trailing hoses. • Slip hazard presented from wet pathways. • Slip hazard for operator when concentrating on work. • Falls from height when working on flat roofs. • Electrocution from poles coming into contact with overhead power source.
Installation & Operating Instructions System Overview Output Valve TDS Meter FastLockTM Lever Output Valve Hose Quick Connect Housing with Rugged Outside Appearance FloWaterTM Unit QuickChangeTM Resin Bag (Packed inside unit) On/Off Valve Inlet Connection 6 ungerglobal.
Installation & Operating Instructions System Overview • Unger nLite HydroPower systems contain mixed bed ion exchange resin to remove impurities out of ordinary drinking water, commonly referred to as pure water. Such impurities are referred to as total dissolved solids (TDS) and are measured in parts per million (ppm). Water is considered 100% demineralized or pure when its TDS is measured at 0 ppm. The average TDS of drinking water is 180 ppm.
Installation & Operating Instructions System Overview (continued) • Larger size models, HP12T/HP12C and HP24T/HP24C, are available with a cart. However, each system can be removed and installed upright in a van or truck. All nLite HydroPower systems must be upright during operation. • nLite HydroPower systems are factory equipped with standard Quick Connect fittings. Conversion kits are commonly available so that feed water and waterfed wash pole tubing can be connected.
Installation & Operating Instructions New Machine Setup 1. U npack Unit: Inspect the nLite HydroPower system and all components. Read warnings and operating manual. 2. I nspection & Scope of Delivery: Refer to above illustration; perform visual inspection and take inventory of the following items that should be shipped with the system, then test system for functionality: a. TDS Meter (powers on/off). b.
Installation & Operating Instructions System Startup 1 2 3 4 10 LOCATE JOBSITE WATER SUPPLY Unger recommends testing the on-site water supply for TDS (total dissolved solids) prior to working. Higher TDS levels reduce the DI system’s capacity. • Inspect system – ensure DI resin bag(s) are installed. • Set up system in upright position. • Choose a stable on-site location. CONNECT WATERFED WASH POLE TUBING • Install Quick Connect adapter to waterfed wash pole hose.
Installation & Operating Instructions System Maintenance - Replacing DI Resin NOTE: Unger does not recommend the use of bulk resin with nLite HydroPower systems. The use of bulk resin, with its widely varying properties, may cause damage to the system due to excessive expansion when water is introduced. Overfilling the system will also cause damage. Unger’s pre-measured QuickChangeTM Replacement Resin Bags are designed to allow controlled resin expansion within a designed safety limit.
Installation & Operating Instructions Operation 1. Periodically inspect the HydroPower system during use. Ensure hoses are properly attached. Inspect system for leaks and proper fit of top cap assembly. 2. Take care when working to ensure there is enough slack in waterfed wash pole hose. This hose is connected to the top of the unit and excessive tugging may cause the system to tip over. 3.
Spare Parts NOTE: Due to safety concerns, unauthorized modifications are not allowed. Original parts and accessories are specifically designed for this device. Any liability by the manufacturer for damages resulting from modifications to the device or from using parts other than original parts is denied.
Notes _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ __
Notes _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ __
Unger Enterprises, LLC 425 Asylum Street • Bridgeport, CT 06610 Tel.: 800 431 2324 • Fax: 800 367 1988 unger@ungerglobal.com Literature # 18484 ungerglobal.