www.pce-industrial-needs.com Tursdale Technical Services Ltd Unit N12B Tursdale Business Park Co. Durham DH6 5PG United Kingdom Phone: +44 ( 0 ) 191 377 3398 Fax: +44 ( 0 ) 191 377 3357 info@tursdaletechnicalservices.co.uk http://www.industrial-needs.
info@tursdaletechnicalservices.co.uk Contents: 1. PCE-UT 2000 Series Digital Storage Oscilloscopes Introduction ........................................ 3 2. Chapter One: Software Structure Basics ............................................................................. 4 3. Chapter Two: Operation Guide ............................................................................................ 7 4. Chapter Three: Installation guide for PCE-UT2000 Series Computer................................
info@tursdaletechnicalservices.co.uk 1. PCE-UT 2000 Series Digital Storage Oscilloscopes Introduction The PCE-UT 2000 Series Digital Storage Oscilloscope software is written for PCEUT2000 Series digital storage oscilloscopes. With this software you can carry out communication between a computer and an oscilloscope through serial or USB, and in turn perform remote control. This software also provides testing, waveform and sampling data reading functions to facilitate further signal testing and analysis.
info@tursdaletechnicalservices.co.uk 2. Chapter One: Software Structure Basics Notes on operation interface Notes on menu: 1. Document: Load waveform, save waveform, load intersection, print preview, print preview, print, exit. 2. Function: Mathematics function: User can select the calculation method of the channels or window function.
info@tursdaletechnicalservices.co.uk Remote control: Control of the serial interface can be performed from a remote point.
info@tursdaletechnicalservices.co.uk Parameter testing: The current parameters are displayed 3.
info@tursdaletechnicalservices.co.uk 4. Help: Content; About Notes on front panel Channel status: Current status of the oscilloscope is displayed. When transmitting data, this status bar displays the current status. When the oscilloscope’s status changes, so will this status bar, but you cannot use this bar to control the current status of the oscilloscope. 1.
info@tursdaletechnicalservices.co.uk We recommend you to read this chapter carefully to familiarize with application. Connect the RS-232 power cord or USB lead. Turn on the oscilloscope and activate the P C E - UT 2000 Series Digital Storage Oscilloscope software. Enter the following screen: USB Interface Controls If controlling the oscilloscope via the USB interface, follow the steps below: 1. With the equipment selection knob on the real-time control panel, select USB. 2.
info@tursdaletechnicalservices.co.uk 6. Click Series on the above screen so the oscilloscope can transmit continuously as indicated below. You can now control the oscilloscope. 7. When operation is complete press [CLOSE] to close this screen. Note: When starting step 5 after completing step 4, you can select [Function] and then [Remote Control] in the menu bar instead of clicking [Data Interface]. The following screen will pop up to allow control of the oscilloscope but no waveform is displayed.
info@tursdaletechnicalservices.co.uk Serial Interface Controls Follow the following steps: 1. Select Serial with the equipment selection knob of the real-time control panel. The following screen appears: Press OK. 2. Click the [Equipment ON/OFF] knob to turn it on. When the indicator lights up the function is ON. When the indicator lights off the function is OFF. 3. Click the [Data Transmission] knob to turn it on. When the indicator lights up the function is ON.
info@tursdaletechnicalservices.co.uk Important: The above screen will not display waveform. Operation of this screen will be indicated in the oscilloscope. 5. At the end of operation press [CLOSE] to close this screen. To switch to USB connection follows the steps for USB connection stated above. When you have finished all operations, press [CLOSE] to switch off the PCE-UT2000 Series Digital Storage Oscilloscope software, then power off the oscilloscope and disconnect the USB lead and RS-232 power cord.
info@tursdaletechnicalservices.co.uk You will also see an icon prompt that says “Found New hardware – PCE- UT2000 Series Digital Storage Oscilloscope”. A “Found New hardware” dialogue box will pop up in a little while, as shown below: Set up as follows: Step 1: Select [Yes, this time only] and click [Next] once. Step 2: In the “Found New hardware Wizard” wizard select [Install from a list or specific location (Advanced)], then click [Next].
info@tursdaletechnicalservices.co.uk The following screen will appear. Select [Browse]. In the popped up [Browse Folder] box, select the DSO directory in the directory where you intend to install PCE-UT2000, then click [Next]. (As shown below). Step 3: Enter the search-in-progress waiting screen.
info@tursdaletechnicalservices.co.uk The dialogue box below will appear but it will not affect the software or your computer. Click [Continue Anyway].
info@tursdaletechnicalservices.co.uk document is copied. The following screen will appear while the document is being copied. Click the left arrow of [Browse…] to select the directory you have defined in Step 2.
info@tursdaletechnicalservices.co.uk If you have not defined any, find one in [Browse…]. Click [OK] again to confirm. Document copy will continue. Click [Finish] to complete installation of the driver.
info@tursdaletechnicalservices.co.
info@tursdaletechnicalservices.co.uk Note: If no [Found New Hardware] wizard pops up on your computer screen when the computer is properly connected to the oscilloscope and the latter is powered on normally, right click [My Computer] and select [Attribute]. In the [System Attribute] dialogue box select the [Hardware] box. Click the [Device Manager] button.
info@tursdaletechnicalservices.co.uk icon that indicates incomplete installation.
info@tursdaletechnicalservices.co.uk New Hardware] wizard. Follow step 1 to install the driver. 3. Installing the software You can install from the installation CD-Rom supplied with the oscilloscope or download the computer software directly from the UNI-T website. Step 1: Find the suitable operating system “PCE-UT2000 VI (For WinXP) or PCE-UT2000 VI (For Win2000)” folder in the supplied CD-Rom or unzipped path.
info@tursdaletechnicalservices.co.uk Step 2: Begin installation. The software installation wizard pops up as shown below : Step 3: Confirm that you wish to install this software. Click the [Next] button.
info@tursdaletechnicalservices.co.uk Step 4: Read the installation licensing agreement carefully. Select “I agree with the terms and conditions of the licensing agreement”, then click [Next]. Step 5: Enter your user name and company name, then click [Next] once.
info@tursdaletechnicalservices.co.uk Step 6: Enter the installation path in the installation path field or click [Change ( )H…..] to select an alternative installation path. Then click [Next] once. Step 7: Depending on your specific requirement, select [Quick installation for the current user only] or [Make quick installation applicable to all users], then click [Next] once.
info@tursdaletechnicalservices.co.uk Step 8: After confirming all information is correct, click [Next] once. Step 9: The successful installation screen appears.
info@tursdaletechnicalservices.co.uk Step 10: When installation is complete as shown above, click [Finish (F)] once on the screen. The software has been installed in your host. If you wish to change any setup, simply click [Back (B)] once during any stage of the wizard. If you wish to stop the installation, click [Cancel] once during any stage of the wizard to quit. 3. Running the Software There are two ways to find this software and run it on your computer. 1.
info@tursdaletechnicalservices.co.uk 5. Chapter Four: System Prompts and Troubleshooting System Prompts Time out prompt: Check the serial configuration or check whether the equipment is properly connected. Time out prompt: Check the USB configuration or check whether the equipment is properly connected. SCAN prompt: SCAN will perform single transmission. Please carry out single refresh. Continue? Are you sure you want to exit Virtual Instrument? A prompt will ask you if you wish to close the software.
