User Guide

ManualsBrandsUNICOM Electric ManualsHardwareGEP-5300TF-C

908 Canada Court

City of Industry, CA 91748 U.S.A.

Phone: 626.964.7873 or 800.346.6668 Fax: 626.964.7880

www.unicomlink.com e-mail: info@unicomlink.com

©UNICOM 2009. UNICOM and “A Network Systems Solution” are trademarks of UNICOM Electric, Inc.

Rev: 06.09

USER’S MANUAL

10/100/1000Base-T

1000Base-SX/LX

Gigabit Ethernet Converter

For full coverage of your warranty, be sure

to register your product using the enclosed

registration card.

GEP-5300TF-C 1000Base-T/SX (SC/MM/550m)

GEP-5400TF-C 1000Base-T/LX (SC/SM/10km)

Rev. 2.0

Summary of content (6 pages)

PAGE 1
For full coverage of your warranty, be sure to register your product using the enclosed registration card. 10/100/1000Base-T 1000Base-SX/LX Gigabit Ethernet Converter GEP-5300TF-C GEP-5400TF-C 908 Canada Court City of Industry, CA 91748 U.S.A. Phone: 626.964.7873 or 800.346.6668 Fax: 626.964.7880 www.unicomlink.com e-mail: info@unicomlink.com ©UNICOM 2009. UNICOM and “A Network Systems Solution” are trademarks of UNICOM Electric, Inc. All rights reserved. Specifications subject to change without notice.
PAGE 2
Package Contents Package contents include the following: ■ 10/100/1000Base-T to 1000Base-SX/LX Converter (Multi-Mode or Single Mode) ■ DC Power Adapter ■ User’s Manual ■ Rack Mount Brackets ■ Warranty card (not shown) Gigabit User’s Manual Converter (Multi-Mode or Single Mode) Power Adapter Rack Mount Brackets IMPORTANT: If any piece is missing or damaged, please contact your local dealer or reseller for service.
PAGE 3
Product Specifications Standard Compliance: IEEE 802.3 10/100/1000Base-T Gigabit Ethernet IEEE 802.3 1000Base-SX/LX Gigabit Ethernet Protocol: CSMA/CD Interface: (1) 10/100/1000Base-T, Shielded RJ-45 Jack (1) 1000Base-SX/LX, Dual SC connector Cable distance: 10/100/1000Base-T Cat. 5e or 6: up to 100m. 1000Base-SX: Multi-mode fiber 50/125µm (550m) 62.
PAGE 4
Key Features Cabling Standards: • Twisted-pair segments can be Unshielded Twisted Pair (UTP) or Shielded Twisted Pair (STP) cabling. The cable must comply with the IEEE 802.3 10/100/1000Base-T standard for Category 5e/6. The cable between the converter and the link partner (switch, hub, workstation, etc.) must be 100 meters (328 ft.) or less in length. IEEE IEEE IEEE IEEE IEEE 802.3 10BASE-T 802.3u 100BASE-TX 802.3ab 1000BaseT, 802.3z 1000BaseSX/LX standards 802.
PAGE 5
Installing Converters into Chassis Follow the steps below to install modular converters into the 10 space Converter Chassis (pn: FEP-593110). A. Remove the blank bracket from the chassis by rotating screw counterclockwise. Put the blank bracket aside. B. Open the rack mount bracket kit. The kit contains two rack mount brackets and four screws.
PAGE 6
LED Indicators DIP Switch Description There are six diagnostic LEDs located on the front panel of these converters. The LEDs provide real-time information on system status. The indicators include SPD, LK/ACT, FDX, Fiber LK/ACT, FDX/COL and PWR. The following table provides describes these LEDs: The DIP-switch is used to configure operation mode for LLF (Link Lost Forwarding) and operation mode for Copper/Fiber port. The default value of Dipswitch is OFF.