User's Manual

x If any items are missing or damaged, contact our Customer Care
Line immediately. Never use damaged products!
x Need Help? Get answers 24/7 at our website: www.uniden.com.
If You... Contact Uniden’s... Phone Number
have a question or problem Customer Care Line*
817-858-2929 or
800-297-1023
need a part or accessory Parts Department* 800-554-3988
need special assistance due
to a disability
Accessibility Help Line
800-874-9314
(voice or TTY)
* During regular business hours, Central Standard Time. Visit our website for detailed
business hours.
Important Safety Instructions!
When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of re, electric shock and injury to persons, including the
following:
x is unit is NOT waterproof. DO NOT expose this unit to rain or moisture.
x Do not use this product near water, for example, near a bath tub, wash bowl, kitchen
sink or laundry tub, in a wet basement or near a swimming pool.
x Avoid using a telephone (other than a cordless type) during an electrical storm. ere
may be a remote risk of electric shock from lightning.
x Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS!
AC adapter
(PS-0045)
Cordless
headset with
ear loop
and ear cap
attached
DHS100 Cordless Headset User's Guide
What's in the box?
PREPARING YOUR HEADSET
Attach Earpiece Loop or Headband
x Choose the appropriate size Earpiece Loop.
x Push the selected Earpiece Loop or Headband
eyelet onto headset mounting peg.
Charge the Battery
1. Connect the AC adapter to the
charge cradle jack and to a wall
outlet.
2. Place the headset in the charging
cradle with the status LED
facing forward. If the LED
doesn’t light up, reseat the
headset or connect the charger
to a different outlet.
3. When the headset is fully charged, the status LED will show blue.
#Charge the headset completely (about 3 hours) before using it.
#Do not charge the headset when the ambient temperature is below
0° C (32°F) or above 40°C (104°F).
REGISTERING TO A BASE
#The accessory headset won't work until you register it to a
compatible Uniden cordless phone!
Compatible Uniden Cordless Phones
Find compatible models at our website: www.uniden.com.
Register the Headset
1. On the phone base, press and hold
FIND HANDSET
for 5 seconds.
#On some models (such as the D3588) press
MENU
, select Register handset
from the display menu selection, and then press
SElEcT.
2. On the headset, press and hold both
VOlUME -
and
+
for 5 seconds.
The status LED alternately blinks slow to fast blue and red while registering.
When registered, a confirmation tone sounds at the phone base and the
headset LED flashes blue once every 10 seconds.
Test the connection
Pick up the headset and press
ON/OFF/TAlK
. Listen for a dial tone. (Press
ON/
OFF/TAlK
to hang up.)
If... Try...
x there is no dial tone
x the error tone sounds
charging the headset until fully
charged and then retry connection.
OPERATION
To power on... To power off...
x press and hold
ON/OFF/TAlK
for 3
seconds
.
x press and hold
ON/OFF/TAlK
for 3
seconds
.
To answer a call... To adjust call or ringer volume...
x press
ON/OFF/TAlK
and speak clearly
x press
ON/OFF/TAlK
again to end call
call (in use) or ringer (standby):
x press
+
to increase or
–
to decrease
To mute the microphone... To answer call waiting call...
x press
MUTE/FlASH
to mute
x press
MUTE/FlASH
again to unmute
x press and hold
MUTE/FlASH
x press and hold
MUTE/FlASH
to return
IMPORTANT INFORMATION
AC Adapter and Battery Specications
AC adapter
Part number Input voltage Output voltage
PS-0045 120VAC, 60 Hz 5.4VDC @ 400mA
x Use only the supplied AC adapter.
x Do not place the unit in direct sunlight or subject it to high temperatures.
Battery information (battery is not user-replaceable)
Type Capacity Talk time Standby time
Lithium-ion 230mAh, 3.7VDC about 6 hours about 3 days
x Please contact Uniden Customer Service if the battery fails.
x When the battery gets low, the headset sounds an alert tone and the status indicator shows red
once every 10 seconds to indicate the unit needs charging.
General InformatIon
• You cannot use the headset while it is charging.
• Actual range varies depending environmental conditions and battery power level.
Cleaning the headset
If necessary, remove the Ear Cap and Earpiece loop. Dampen a lint-free cloth with water or
a cleaner specially designed for electronics, and gently wipe the headset clean.
Do not expose this product to liquid (water, alcohol, etc.) or
submerse in liquid for any reason.
Flash
Mute
Headset peg
Earloop
Earloop
eyelet
VOLUME +/-
ON/OFF/TALK
STATUS LED
MUTE/FLASH
Charge cradle
Additional
earpiece loops (2)
Additional ear caps (2)
Headband