App Cam Spotlight+ Quick Start Guide
What’s in the Box App Cam Solo+ Camera x1 Reset Needle x1 Power Adaptor x1 Camera Bracket x1 Screw Kit x2 Mounting Template x2 1
General Introduction Speaker Power cable Spotlight Status LED Blinking : Wi-Fi connection failed On: Camera is starting up/Wi-Fi connection succeeded Lens Daylight Sensor Built-in Mic PIR Motion Sensor Micro SD Card Slot Reset Button Press for more than five seconds to restore default settings 2
Install Uniden Solo App There are two ways to get the Uniden Solo App: • Search “Uniden Solo” in App Store (for iOS), download and install the app. • Search “Uniden Solo” in Google Play (for Android), download and install the app. Set up the Camera Please follow the prompt tone to configure the camera Please run app, add the camera and set it up. 1. Please click the “ ” button in the top right corner to add the camera.
Note: When the setup for the camera is completed, your family can access the camera simply by clicking “Access Cameras” without reconfiguring it. App Cam Spotlight+ Camera can only connect to 2.4GHz Wi-Fi. 2. Scan the QR code on the bottom of the camera. 3. Click “Connect to Wi-Fi” to continue.
4. Click the button “I heard the voice” to enter the next page. 5. Enter the Wi-Fi password of the selected Wi-Fi network and tap “Next” to continue. If you did not hear the voice prompt, please press “I did’t hear the voice” for help.
About 20cm Scan succeeds. Camera is connecting to the router. Please wait. 6. A QR code will be generated on the phone. Please place the QR code on your phone towards App Cam Solo+ camera’ lens at a distance of about 20cm to let the camera scan the QR code. Please make sure that you’ve ripped the protection film of the camera’s lens.
Connection to the router failed! 7. If you hear the above voice prompt, please press “I heard ‘Wi-Fi connection failed’ ” for help. Connection to the router succeeded. 8. If you hear the above voice prompt, please press “I heard ‘Connection to the router succeeded.’ ” to finish the quick setup.
. Create a password (at least 6 characters) and name the camera. Then start live view or go to “Device Settings” for more configurations. Note: “Name your camera” field refers to the display name of the camera rather than the login username.
Device Menu Menu Add New Device Device Settings Access Live View 9
Attention for Camera Installation Select an Installation Height Please install the camera 2-3 meters above ground. This height maximizes the detection range of the motion sensor. For effective motion detection, please install the camera angularly and the angle between the PIR sensor and the detected object must be larger than 10°.
PIR Sensor Detecting Distance The PIR detection range can be adjusted to meet specific needs. You can refer to the following table to set it up in Uniden Solo App Device Settings. Higher sensitivity offers longer detecting distance, but it would lead to more false alarms. You are advised to set up the sensitivity level to “Low” or “Mid” when you install the camera outdoors.
! Important Notes for Reducing False Alarms For reducing false alarms, please note that: • • • • • • Do not install the camera facing any objects with bright lights, including sunshine, bright lamplights, etc. Do not place the camera too close to a place where there are frequently moving vehicles. The recommended distance between the camera and the vehicle is 15 meters Do not install the camera where there are strong winds.
How to Install Wall Mount Step 1 Step 2 Rotate and open the bracket. Drill holes in terms of the provided mounting hole template and insert the plastic anchors into the hole. Screw the bottom of the bracket onto the wall and then attach the other part of the bracket onto the bracket bottom. Step 3 Fasten the camera to the bracket by turning the screw identified in the following chart anticlockwize.
Step 4 Step 5 Adjust the camera angle, and get the best viewing angle when you see the live feed in the Uniden Solo App. Secure the camera by turning the part on the bracket identified in the image clockwise. NOTE: In case you will need to adjust the camera angle later, please loosen the bracket by turning the upper part anti-clockwise.
Troubleshooting Camera is not powering on If your camera is not powering on, please try the following: • Plug the camera into another outlet. • Use another 5V power adapter to power up the camera. Fail to scan the QR code on the phone If the camera failed to scan the QR code on your phone , please try the following: • Remove the protective film on the lens of the camera. • Wipe the camera lens with a dry paper/ towel/tissue.
Specifications Model App Cam Spotlight+ Image Sensor 1/2.8” CMOS Image Sensor Video Resolution 1920 x 1080 (2.0Megapixel) 15 fps Video Compression Video & Audio H.264 Viewing Angle Diagonal: 120° PIR Detecting Distance WiFi up to 7 meters PIR Detecting Angle Horizontal: 100° Night Vision Up to 10 Meters Audio Two-way talk Alerts PIR + Motion Detection WiFi 2.4 GHz IEEE 802.11b/g/n Wireless Security WPA-PSK/WPA2-PSK Power Hardware DC 5.0V/2A, <6W Spotlight 1.
WARRANTY Uniden App Cam Spotlight+ Important: Satisfactory evidence of the original purchase is required for warranty service. Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below. Warrantor: The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden Aust”).
Parts Covered: This warranty covers the Product and included accessories. User-generated Data: This warranty does not cover any claimed loss of or damage to user-generated data (including but without limitation phone numbers, addresses and images)that may be stored on your Product. Statement of Remedy: If the Product is found not to conform to this warranty as stated above, the Warrantor, at its discretion, will either repair the defect or replace the Product without any charge for parts or service.
THANK YOU FOR BUYING A UNIDEN PRODUCT © 2020 Uniden Australia Pty Limited V1.