DCX200.
DCX200.indd 1 Welcome Congratulations on your purchase of the Uniden DCX200 accessory handset and charger. You can place this fully featured cordless handset anywhere your home has AC power. Note: Illustrations in this manual are used for explanation purposes. Some illustrations may differ from the actual unit. Accessibility Uniden provides a customer service hotline for accessibility questions.
DCX200.indd 2 Compatible Bases This handset is compatible with Uniden's 1.9 GHz DECT6.0 Expandable phone system: the DECT2000 series. Please visit our website at www.uniden.com for the most up-todate list of compatible bases. Installing the Accessory Handset Checking the Package Contents Make sure your package contains the following items. If any items are missing or damaged, contact our Customer Service Hotline. See inside the back cover page for contact information.
DCX200.indd 3 Installing the Belt Clip Line up the tabs with the holes on each side of the handset. Press the belt clip down until both tabs click into place. To remove the belt clip, pull both sides of the clip to release the tabs from the holes. Installing the Optional Headset Your phone may be used with an optional headset. To use a headset, insert the headset plug into the headset jack. Headsets may be purchased by calling the Uniden Parts Department.
DCX200.indd 4 Registering the Handset You must register the handset to the base before you can use it. Only one handset can be registered at a time. (If an accessory handset has ever been registered to a base, you must reset the handset before you can register it to a new base.) To register to a DECT2000 1 series base, place the Charge the handset Extra Handset accessory handset in the base. for 15-20 hours. While the handset is registering, Charger HANDSET REGISTERING appears in the LCD.
DCX200.indd 5 Resetting the Handset Without the Base If the original base this handset was registered to is not available for some reason (for example, it is lost or somehow incapacitated), you can still reset the handset and use it with another base. ) Press and hold [ ] and [#] for more than five seconds, until the SYSTEM RESET menu appears. 2) Press [ ] to move the cursor to BASE UNAVAILABLE and then press [Menu/Select]. WHICH BASE? appears.
DCX200.indd 6 Using the Interface Parts of the Handset 1 5 6 2 3 7 14 8 9 10 11 15 16 17 18 12 13 19 20 4 21 22 . 2. 3. Headset jack cover Belt clip hole Speakerphone speaker and ringer 4. Handset battery compartment 5. new message LED 6. Handset earpiece 7. LCD display 8. [Clear/Int’com] key 9. [ ] key (up) 0. [ /Flash] key (talk/flash) . [ ] key (phonebook/left) 2. 3. 4. 5. 6. 7. 8. 9. 20. 2 . 22.
DCX200.indd 7 Reading the Display The handset display uses icons to tell you the status of your phone. The table below lists the icons and what they mean. Icon Status Standby/ Talk :OFF Standby Talk Talk Talk Standby Description The battery icon indicates the handset battery status: full, medium, low, and empty. The ringer off icon indicates that the ringer is turned off. The mute icon appears while the handset microphone is muted. The speaker icon appears when the handset speaker phone is in use.
DCX200.indd 8 Using the Handset Menus To open the menu, press [Menu/Select]. Highlight the option you want by pressing the four-way function key. This will move the cursor; the option currently highlighted has a triangle beside it. Activate the highlighted option by pressing [Menu/Select]. To go back to the previous screen, press [left] on the four-way function key. To exit the menu and return to standby, press [ ]. If you do not press a key within thirty seconds, the phone will time out and exit the menu.
DCX200.indd 9 For example, to enter the word "Movies": ) Press [6] once to enter M. 2) Use [right] on the four-way function key to move the cursor to the right. 3) Press [6] six times to enter o. 4) Press [8] six times to enter v. 5) Press [4] six times to enter i. 6) Press [3] five times to enter e. 7) Press [7] eight times to enter s. 8) Press [Menu/Select] to end your text entry.
DCX200.indd 10 Using Your Accessory Handset Making and Receiving Calls With the earpiece Make a call ) Pick up the handset from the cradle. 2) Dial the number. 3) Press [ /Flash]. ) Pick up the handset. (If AutoTalk is on, the phone answers when you pick up the handset from Answer the cradle.) a call 2) Press [ /Flash]. (If Any Key Answer is on, you can press any key on the dial pad.) With the speaker phone ) Pick up the handset from the cradle. 2) Dial the number. 3) Press [ ].
DCX200.indd 11 Using Caller ID and Call Waiting If you subscribe to Caller ID, you can store up to thirty Caller ID numbers in each handset. Caller ID records are stored from newest to oldest. Once your Caller ID list is full and you receive an incoming call, the oldest record will be automatically deleted to make room for the new record. To open the Caller ID list, press [ ]. The phone will show the number of new Caller ID records and the total number of stored records.
DCX200.indd 12 Using the Phonebook Your handset can store up to seventy names and numbers in your phonebook. When all the phonebook entries are full, you will hear a beep and MEMORY FULL appears. You cannot store any additional names and numbers unless you delete some of the existing ones. Press [ ] to enter the phonebook. Once in the phonebook, you have the following options: Scroll through Press [ ] to scroll through the phonebook the entries alphabetically.
DCX200.indd 13 Redialing a Number To redial one of the last five numbers dialed on this handset, press [Redial/Pause]. This opens the redial list. Use [ ] and [ ] to find the number you want to dial, and press [ /Flash] or [ ] in standby, or press [Menu/Select] during a call. Muting the Ringer (One Call Only) While the handset is ringing, press [ ] to mute the ringer for this call. The phone will ring again on the next call. (The handset must be off the cradle to mute the ringer.
DCX200.indd 14 Using Hold, Conference, Transfer and Intercom Press [Clear/int’com]. If you leave a caller on for more than five minutes, the call will be Put a call on hold hold disconnected. To return to the party on hold, press [ /Flash] or [ ]. To join a call already in progress, press [ /Flash] Join a call already or [ ]. You can hang up normally; the other in progress station remains connected to the call. Transfer a call Press [Clear/int’com]; the call is placed on hold.
DCX200.indd 15 Accessing Voicemail If your base doesn't have an answering system and you subscribe to a voice mail service, you can program your handset to automatically dial the access number. ) Press [Menu/Select]. 2) Move the cursor to HANDSET SETUP and press [Menu/Select]. 3) Move the cursor to EDIT VOICE MAIL and press [Menu/Select]. 4) Enter your access number (up to twenty digits). If you need the phone to wait before sending the next digits, press [Redial/Pause] to insert a two-second pause.
DCX200.indd 16 Screening Calls If your base has an answering system, you can listen to callers as they leave a message. Press [ /Mute] when the system is answering to listen to the caller without answering the phone. Maintenance Battery Life With average use, your battery talk time will be approximately ten hours and standby time will be approximately seven days. For optimum performance, be sure to return the handset to the cradle after each call.
DCX200.indd 17 Caution: - This equipment contains a rechargeable Nickel-Metal-Hydride battery. - Do not remove the batteries to charge them. - Never throw the battery in a fire or disassemble or heat it. - Do not remove or damage the battery casing. - Nickel is a chemical known to state of California to cause cancer. - Do not short-circuit the battery. - Do not charge the battery used in this equipment in any charger other than the one designed to charge this battery as specified in the owner's manual.
DCX200.indd 18 To insure the safety of users, the FCC has established criteria for the amount of radio frequency energy various products may produce depending on their intended usage. This product has been tested and found to comply with the FCC's exposure criteria. For body worn operation, the FCC RF exposure guidelines were also met when used with the Uniden accessories supplied or designed for this product.
DCX200.indd 19 One Year Limited Warranty Important: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.
DCX200.indd 20 LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is void outside the United States of America and Canada. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner's manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging).
DCX200.
DCX200.indd 22 At Uniden, we'll take care of you! Thank you for purchasing a Uniden product. if you have any questions or problems, please do not return this product to the place of purchase. Our customer care specialists are here to help you! Visit our website at www.uniden. com or call our Customer Service Hotline at 1-800-297-1023 during regular business hours.* Having trouble? To order headsets, additional handsets, batteries, or other accessories, Need a part? replacement visit our website at www.
A World Without Wires® VISIT WWW.UNIDEN.COM TO REGISTER YOUR PRODUCT © 2007 Uniden America Corp, Ft Worth, TX. Contains additional foreign articles. Printed in China. UUZZ01644BZ(0) DCX200.
