Contents Welcome/Accessibility...................................................2 Terminology/Manual Conventions................................3 Product Overview...........................................................4 Controls and Functions.................................................5 Installing the Phone.......................................................7 Redialing the Last Dialed Number..................................... 26 Selecting the Ring Tone and Volume.............................
Welcome Congratulations on your purchase of the Uniden multi-handset cordless telephone. This cordless phone is designed for reliability, long life, and outstanding performance. Note: Illustrations in this manual are used for explanation purposes. Some illustrations in this manual may differ from the actual unit. The color of your cordless telephone may vary. Uniden® is a registered trademark of Uniden America Corporation.
Terminology Base The main part of the phone that connects to your phone line and lets you make and receive calls. Charger A cradle that charges the handset battery. It connects to power but does not connect to a phone line. Caller ID is available from your telephone provider. With this service, you can see the name and number CID of incoming callers. Caller ID on Call Waiting is available from your telephone provider. With this service, you can see CIDCW incoming caller information while on another call.
Product Overview Main Phone Features • 5.
Controls and Functions Handsets 1. Handset antenna 2. Belt clip hole 3. Jack for optional headset 4. Handset ringer speaker 5. Handset battery compartment 6. Handset earpiece 7. LCD display 8. [ ] and [ ] (volume & ringer up/down) keys 9. [cid/menu] key 10. [ /tone/ ] (left cursor) key 11. [redial/pause] key 12. [select/channel] key 13. [talk/flash] key 14. [end] key 15. [#/ ] (right cursor) key 16. [mem] (memory) key 17. [delete/transfer] key 18. Handset microphone 19.
Main Base Unit 20. Base antenna 21. Base charging contacts 22. Base speaker 23. Message counter LED 24. [ ] (answer on/off) key 25. charge/in use LED 26. [ ] (delete) key 27. [ ] (play/stop) key 28. [ ] (skip/fast forward) key 29. [ringer] key 30. [find hs] key 31. [greeting] key 32. [volume/select/ ] (up) and [volume/select/ ] (down) keys 33. [ ] (repeat/rewind) key 34. [menu/clock] key 35. [set] key 36. Mic (microphone) 37. [memo] key 38. TEL LINE jack 39. Base DC IN 9V jack 40. Charging contacts 41.
Installing the Phone Choosing the Best Location Before choosing a location for your new phone, here are some important guidelines you should consider: Avoid heat sources, such as radiators, Avoid noise sources such as a window by air ducts, and sunlight a street with heavy traffic Avoid television sets and other Avoid microwave ovens electronic equipment Avoid excessive moisture, extremely low temperatures, dust, mechanical vibration, or shock Choose a central location Avoid personal computers Avoid othe
Installing the Rechargeable Battery Packs into the Handsets Each handset is powered by a rechargeable battery pack. Once installed, the battery charges automatically when the handset is placed in the base or charging cradle. To install the rechargeable battery pack: 1) Press down on the handset battery case cover (use the finger indention for a better grip) and slide the cover downward to remove. 2) Plug the battery pack connector (red & black wires) into the small jack inside the battery compartment.
Installing the Base Unit and Charging Cradles 1) Connect each AC adapter to the DC IN 9V jack and to each standard 120V AC wall outlet. Note: • Use only the supplied AD-314 AC adapter for the base unit and AD-310 or AD-1010 for the charging cradle(s). Do not use any other AC adapter. • Do not place the power cord where it creates a trip hazard or where it could become chafed and create a fire or electrical hazard.
3) Make sure that the charge/in use LED and LED illuminate. If the LED does not illuminate, check to see that the AC adapter is plugged in and that the handset makes good contact with the cradle’s charging contacts. Note: • Connect the AC adapter to a continuous power supply (not controlled by a wall switch). • Place each cradle close to the AC outlet to avoid long extension cords. • Charge your handsets at least 15 - 20 hours before plugging into the phone line.
Mounting the Base Unit on a Wall Standard wall plate mounting This phone can be mounted on any standard wall plate. 1) Plug the AC adapter to the DC IN 9V jack. 4 2) Route the AC adapter cord through the molded wiring channel as shown. 1 7 5 2 6 3) Plug the AC adapter into a standard 120V AC wall outlet. 7 4) Plug the telephone line cord into the TEL LINE jack. 5) Route the telephone line cord through the molded wiring channel as shown. 6) Plug the telephone line cord into the telephone outlet.
• Make sure the wall material is capable of supporting the weight of the base and handset. • Use #10 screws (minimum length of 1-3/8 inches) with anchoring devices suitable for the wall material where the base unit will be placed. 1) Insert two mounting screws into the wall (with their appropriate anchoring device), 3-15/16 inches apart. Allow about 1/8 of an inch between the wall and screw heads for mounting the phone. 2) Refer to steps 1 through 7 on page 11 to mount the telephone.
Register Handsets to the Main Base before Using! Each handset will need to be registered to the main base unit before use. Whichever handset you choose to charge in the base unit will automatically register to the base unit. The handset charging in the extra charging cradle MUST also be registered to the base unit before use. To register the extra handset(s): 1) Be sure all handsets are fully charged. 2) Pick up the handset from the charging cradle, and place it in the base unit.
When to Re-register Handsets In some cases, it may be necessary to re-register your handsets. To re-register your handsets, please follow registration steps outlined on page 13. Re-registration is required in the following scenarios: 1) Each time the digital security code is changed. (Refer to page 47 for details regarding the Digital Security Code.) 2) When there is a power failure for more than one hour.
Basic Setup There are five basic options that you will need to set up: AutoTalk, CIDCW (Caller ID on Call Waiting), Area Code, Dial Mode and Language. CIDCW and Dial Mode options can only be set by using Handset 1. If you try to set by using other handset, you will not see these options listed on the LCD screen. (You can easily identify Handset 1 shows as HS1 will be seen in the display while the phone is charging.) AutoTalk, Area Code and Language options can be set by using any handset.
Activating Caller ID on Call Waiting (HS1 only) Caller ID allows you to see the name and number of the calling party before you answer the phone. Caller ID on Call Waiting (CIDCW) lets you see the name and number of a call that comes in when you are on the line. You must subscribe to Caller ID service through your local telephone provider to use this feature. 1) When the phone is in standby, press and hold [cid/menu]. The following screen appears. 2) Press [ ] to move the pointer to select CIDCW.
2) Press [ ] to move the pointer to select AREA CODE. 3) Press [select/channel]. If an area code was already stored, the phone will display it. 4) Use the number keys ( [0] – [9] ) to enter the three-digit area code. If you make an error, use [delete/transfer] to backspace. 5) Press [select/channel]. A confirmation tone sounds. 6) Press [end] or return the handset to the charging cradle to complete the setting. The handset returns to standby.
2) Press [ ] to move the pointer to select DIAL. 3) Press [select/channel] to set the phone to pulse dialing. 4) Press [end] and return the handset to the base unit to complete the setting. The handset returns to standby. Note: • If your phone system requires pulse dialing and you need to send the DTMF tones during a call, you can temporarily switch over to tone dialing. (Refer to "Tone Dialing Switch-over" on page 28.
Using the Speed Dial Memory Your cordless phone allows you to store up to ten names and numbers in each handset. You can dial these numbers with just a few key presses. The speed dial memory is not limited to phone numbers. You can store any number (up to twenty digits) that you need to enter once your call connects. This is referred to as Chain Dialing. An example is a frequently refilled prescription number.
4) Enter a name according to the instructions below, then press [select/channel]. If no name is required, go to step 5. • The name can be up to thirteen characters. • Use [ /tone/ ] and [#/ ] to move the cursor to the desired location. • Press [delete/transfer] to delete characters as needed or press and hold to delete all characters. Refer to the letters on the number keys to select the desired characters.
If you make a mistake while entering a name Use [ /tone/ ] or [#/ ] to move the cursor to the incorrect character. Press [delete/transfer] to erase the wrong character. Then enter the correct character. To delete all characters, press and hold [delete/transfer]. 5) STORE NUMBER is displayed. The cursor flashes indicating that the phone is ready for the number to be entered. 6) Use the keypad to enter the phone number; each number can be up to twenty digits.
Storing Caller ID in Speed Dial Memory Caller ID names and numbers shown in the Caller ID list can be stored in speed dial memory. To store a caller id name/number to memory: 1) With the phone in standby, press [cid/menu]. Select the phone number to be stored from the Caller ID list by pressing [ ] or [ ]. 2) Press [mem]. 3) Enter a number ( [0] – [9] ) or press [ ] or [ ] to select the memory location to be stored. 4) Press [select/channel].
Using Your Phone Making and Receiving Calls Making a call Receiving a call Hanging up Handset on the cradle 1) Pick up the handset from the cradle. 2) Press [talk/flash]. 3) Listen for the dial tone. 4) Dial the number. OR 1) Pick up the handset from the cradle. 2) Dial the number. Then press [talk/flash]. 1) Pick up the handset from the cradle. (If AutoTalk is on, the phone will answer the call when you pick it up.) 2) Press [talk/flash]. Press [end] or return the handset to the cradle.
2) Enter the number ( [0] – [9] ), or press [ ] or [ ] to select the speed dial number you would like to dial. 3) Press [talk/flash]. CONNECTING changes to TALK, and the volume setting and the number selected appear on the display. Then the displayed number is dialed. Note: You can also press [talk/flash] before you access the speed dial memory. When you come to the phone number you want to dial, press [select/channel]. To cancel speed dialing Press [end] to return to standby.
Transferring a Call Your cordless phone allows you to transfer outside calls from one handset to another. Only one handset at a time can talk with an outside caller. While one handset is in use, other handsets cannot go off hook to listen to conversations or make an outgoing call. To transfer a call 1) During a call, press [delete/transfer]. The call will automatically be placed on hold. Select Handset 2) For 2-handset model: The transfer tone sounds.
Redialing the Last Dialed Number 1) 2) 3) 4) Pick up the handset from the cradle. Press [talk/flash]. Listen for the dial tone. Press [redial/pause]. OR 1) Pick up the handset from the cradle. 2) Press [redial/pause]. 3) Press [talk/flash]. Selecting the Ring Tone and Volume Your phone has five different ringer tone/volume combinations you can choose from. To select the ringer: 1) With the phone in standby, press [ ] or [ ]. 2) The phone will sound the different ring tones at different volumes.
Using Call Waiting If you subscribe to Call Waiting through your local telephone company, you can receive calls while on the line. To answer a call waiting call: 1) While on the phone, you will hear a call waiting tone. (If you have CIDCW service activated, you will see the name and number of the incoming caller. See page 29 for more information) 2) Press [talk/flash] to accept the waiting call. After a short pause, you will hear the new caller.
Find Handset To locate a lost handset, press [find hs] on the base. All registered handsets will beep for 60 seconds. The beeping will stop when any handset key is pressed or when [find hs] is pressed. The handset will also stop beeping automatically when an incoming call is received. Tone Dialing Switch-over If your telephone company requires pulse dialing, you can temporarily switch over to tone dialing after the call connects.
Caller ID and CIDCW (Caller ID on Call Waiting) You must subscribe to Caller ID services through your local telephone provider to use these features. When the telephone rings, the Caller ID feature allows you to view the caller’s name, phone number, date and time of call. The incoming call information is stored in the Caller ID record. If the Caller ID service includes the caller’s name, the caller’s name appears on the display (up to fifteen letters).
Caller ID on Call Waiting (CIDCW) If you subscribe to CIDCW offered by your telephone company, you will hear a Call Waiting tone while you are on a call, and the Caller ID data will be displayed at the handset. To accept the waiting call, press [talk/flash] (see page 27). Note: While you are on a call, the received Caller ID data is stored on the handset that is on a call only.
Deleting Information from the Caller ID List If the phone receives more Caller ID messages than it can store, the oldest one in the list is automatically deleted. Caller ID data can also be deleted manually. Deleting a Caller ID message 1) With the phone in standby, press [cid/menu]. Find the message to be deleted from the Caller ID list by pressing [ ] or [ ]. 2) Press [delete/transfer]. 3) Press [ ] or [ ] to select YES, and then press [select/channel].
The Integrated Answering Machine The cordless phone has a built-in answering machine that answers and records incoming calls. You can also use your answering machine to record a conversation, leave a voice memo message, or to announce a special outgoing message to callers when you're away from your phone.
Setting Up Your Answering Machine Answering Machine Setting To set the following six functions you must enter the menu mode. • With the phone in standby, use [menu/clock] to scroll through the menu options. The system returns to standby and sounds a tone after the last menu option.
Setting the Time The clock on the cordless phone’s answering machine starts when power is supplied to the base. Follow these steps to set the clock to the correct time. 1) With the phone in standby, press [menu/clock]. The system announces "Time" followed by the current time and the instructions for setting the time. 2) Press [volume/select/ ] or [volume/select/ ] until the correct day is announced. The numbers [ ] through [ ] are displayed on the base. 3) Press [set] to select the day.
You hear a confirmation tone followed by the announcement "Time," and the day and time are then announced for your review. After a few seconds, the system announces "To set security code, press menu again." Note: • Normally, the system will return to standby if it remains idle for ten seconds after [volume/select/ ] or [volume/select/ ] is pressed. For setting the time, however, the idle time is extended to two minutes.
Setting the Ring Time The ring time setting allows you to set the number of rings the caller hears before your answering machine plays the outgoing message. You can set the ring time to answer after two, four, or six rings. If you select Toll Saver [ ], the answering machine picks up after two rings if you have new messages, and after four rings if there are none. This way, if you make a long distance call to check your messages, you can hang up after the second ring to avoid billing charges.
2) Press [volume/select/ ] or [volume/select/ ] until the desired time appears. 3) Press [set] to select the new recording time. You hear a confirmation tone, then the announcement "Record time" followed by the new recording time. After a few seconds, the system announces "To set message alert, press menu again." Note: After setting the Announce only feature, you may want to change your outgoing message not to prompt the caller to leave a message. However, the prerecorded message changes automatically.
Selecting the Language The answering machine voice announcements can be heard in English, French or Spanish. To choose the language of the answering machine voice announcements: 1) With the phone in standby, press [menu/clock] six times. You hear the announcement "Language, English" followed by the voice prompts for setting the language. The current setting ([ ], [ ] or [ ]) appears on the base. 2) Press [volume/select/ ] or [volume/select/ ] to select the desired language. 3) Press [set].
Recording a personal outgoing message (Greeting) 1) With the phone in standby, press and hold [greeting]. You will hear the announcement "Record greeting" and a confirmation tone. [ ] flashes on the message counter. 2) Start recording your message. You have thirty seconds, and the message counter starts to count down [ ] to [ ] every second. 3) When you are finished recording your greeting, press [greeting], [ ] (play/stop) or [set]. You hear a confirmation tone, and then your greeting plays back for you.
Setting the Base Ringer Volume The base has three ringer volume settings: high, low, and off. You can change the ringer volume while in standby or while an incoming call is ringing. 1) Press [ringer]. You hear the ringer at the current volume level ([ ] High, [ ] Low, [ ] off) (if you set the base ringer volume to off, "Ringer off" is announced) and it is displayed on the base. 2) Press [ringer] repeatedly until the desired ringer option appears. 3) The system displays the new ringer volume.
Using Your Answering Machine Turning the Answering Machine On/Off To turn the answering machine on: 1) With the phone in standby, press [ ] (answer on/off). 2) The phone announces "Answering system is on." and plays the current greeting. 3) The message counter displays the number of messages stored in memory. If the counter flashes, then you have new messages waiting. To turn the answering machine off: 1) With the phone in standby, press [ ] (answer on/off) again.
Reviewing Messages The message counter displays the number of messages stored in memory. If the display flashes, new messages waiting for you. The flashing number represents the number of new messages, not total messages. The cordless phone plays your new messages first; after all the new messages are played, you can play the old messages.
Recording a Conversation You can record up to ten minutes of conversation while you are using your phone. Any conversation that lasts less than two seconds will not be recorded. 1) During a conversation from the handset, press and hold [memo]. The unit begins recording with a confirmation tone and [ ] flashes on the message counter. A beep that can be heard by both parties sounds during recording. 2) To stop recording, press [ ] (play/stop) or [memo]. You hear a confirmation tone.
Voice Memo The voice memo function allows you to record messages as short as two seconds and as long as four minutes. 1) With the phone in standby, press and hold [memo]. You hear an announcement "Record memo message" and a tone. [ ] flashes on the message counter. 2) Start your recording. 3) When you have finished, press [ ] (play/stop), [memo] or [set] to stop recording. You hear a confirmation tone and the system returns to standby.
4) You may continue to listen to the voice prompts, or you may select a command from the following chart: Command [0] then [1] [0] then [2] [0] then [3] [0] then [4] [0] then [5] Function Repeat a Message Play Incoming Messages Skip a Message Delete a Message Stop Operation Command [0] then [6] [0] then [7] [0] then [8] [0] then [9] [1] then [0] Function Answering Machine On Memo Record/Stop* Greeting Message Record/Stop* Answering Machine Off Voice Prompts * For Memo Record and Greeting Message Record
Turn on the Answering Machine Remotely If you have forgotten to turn on your answering machine, you can turn it on remotely from any touch-tone telephone. 1) Call your telephone number. 2) Wait ten rings until the system answers. You hear intermittent beeps. 3) Press [0] and then enter your PIN code. The answering machine announces the number of messages stored in memory. You hear "To play incoming message, press zero two. For help, press one zero." 4) Press [0] then [6] to turn the answering machine On.
Changing the Digital Security Code To protect you against misbilled calls which might result from your phone being activated by other equipment, the cordless phone provides Random Code™ digital security which automatically selects one of over 262,000 digital security codes for each handset and the base. If the handset battery pack is completely discharged or the battery pack is removed, the digital security code will be lost.
Maintenance Specifications The phone complies with FCC Parts 15 and 68. Operating temperature AC Adapter Battery Frequency -10°C to +50°C (+14°F to +122°F) For the base Part number AD-314 Input Voltage 120V AC 60Hz 9V DC 350mA Output Voltage BT-905 Part number Capacity 600mAh, 3.6V 921.103102-923.787761 MHz 5856.533347-5863.692437 MHz For the charger AD-310 or AD-1010 120V AC 60Hz 9V DC 210mA Note: To avoid damage to the phone use only Uniden AD-314, AD-310 or AD-1010 and BT-905 with your phone.
Talk and Standby Times With average use, your handset battery provides approximately six hours of talk time and approximately ten days of standby time. When your handset is not being used and is left off of the charging cradle the battery will gradually discharge. You can achieve optimum battery life and performance by returning the handset to the charging cradle after each use.
Battery replacement and handling Recharge your phone on a regular basis by returning the handset to either cradle after each phone call. When the operating time becomes short even after a battery is recharged, please replace the battery. With normal usage, your battery should last about one year. To order replacement batteries, please contact Uniden’s Parts Department. The contact information is listed on the back cover page.
Troubleshooting Traveling Out-of-Range During a call, as you begin to move your handset too far from your base unit, noise increases. If you pass the range limits of the base, your call will terminate within one minute. Common Issues If your phone is not performing to your expectations, please try these simple steps first. If these steps do not solve your problem, please call our Customer Hotline. See back cover page for contact information.
Symptom Can’t make or receive calls. The handset doesn’t ring or receive a page. Severe noise interference. Suggestion • Re-register all handsets (see page 13). • Check both ends of telephone line cord. • Make sure the AC adapter is plugged into the base and wall outlet. • Disconnect the AC adapter for a few minutes, then reconnect it. • Change the digital security code (see page 47). • Make sure that the handset is not too far from the base. • Check the dialing mode used by your telephone company.
Symptom The Caller ID does not display. A handset is not working. Unavailable message is displayed on the LCD screen of the handset. Suggestion • The call was answered before the second ring. • The call was placed through a switchboard. • Charge the handset. • Your Caller ID service may not be active; contact your local telephone service provider. • Make sure the battery pack is connected to the handset and fully charged. • Re-register the non-functional handset.
Symptom Messages are incomplete. Suggestion • The incoming messages may be too long. Remind callers to leave a brief message. • The memory may be full. Delete some or all of the saved messages. • Record your personal outgoing message again. The default message should remain. After a power failure, the outgoing message is deleted. No sound on the base speaker during call monitoring • or message playback. • Cannot access remote call-in • features from another touchtone phone.
Liquid Damage Moisture and liquid can damage your cordless phone. • If the handset or base is exposed to moisture or liquid, but only the exterior plastic housing is affected, wipe off the liquid, and use as normal. • If moisture or liquid has entered the plastic housing (i.e. liquid can be heard in the phone or liquid has entered the handset battery compartment or vent openings on the base), follow the steps below: Handset 1) Remove the battery cover and leave it off for ventilation.
Precautions! Rechargeable Nickel-Cadmium . Batteries Must Be Recycled or . Disposed of Properly Before you read anything else, please note the following: Warning! • Uniden voluntarily participates in an RBRC® industry program to collect and recycle nickelcadmium batteries at the end of their useful life, when taken out of service within the United States.
Important Safety Instructions The FCC Wants You To Know When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
I.C. Notice the unlikely event that you consistently hear other voices or distracting transmissions on your phone, you may be receiving radio signals from another cordless telephone or other source of interference. If you cannot eliminate this type of interference, you need to change to a different channel. Finally, it should be noted that some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCRs.
One Year Limited Warranty ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.
Index A Connect the cradle........................... 9 Ringer tone..................................... 26 Controls and functions................. 5, 6 Ringer volume.......................... 26, 40 Ring time........................................ 36 D, E, F, G, H, I, J, K, L Dial mode....................................... 17 S Digital security code....................... 47 Security code Earpiece volume............................. 26 Answering machine.................... 35 Find handset...............
Memo 62
Memo 63
Remote Operation Card C UU TT C C UU TT C REMOTE OPERATION CARD Remote access away from home Turn on the answering system remotely 1. Call your phone number from a touch-tone phone. 2. During the outgoing message, press [0] and enter your PIN code. The answering system announces the number of messages stored in memory and the voice prompts. The phone stands by for you to enter a command. 3. To quit, hang up the phone. 1. Call your phone and let it ring 10 times until it answers. 2.
Remote Operation Card CC UU TT MEMORY LOCATION MEMO Memory Location Name Phone Number 6 7 8 9 10 CC UU TT Task Repeat a Message Play Incoming Messages Skip a Message Delete a Message Stop Operation Answering System On Memo Record/Stop Greeting Message Record/Stop Answering System Off Voice Prompts CC UU TT 6 7 8 9 10 Name 1 2 3 4 5 6 7 8 9 0 CC UU TT MEMORY LOCATION MEMO Memory Location Key 0 0 0 0 0 0 0 0 0 1 Phone Number Task Repeat a Message Play Incoming Messages Skip a Message Delete
At Uniden, we’ll take care of you! Thank you for purchasing a Uniden product. If you have any questions or problems, please do not return this product to the place of purchase. Having Trouble? Need a Part? Help for our Special Needs Customers Our customer care specialists are here to help you! Visit our website at www.uniden.com or call our Customer Hotline at 1-800-297-1023 during regular business hours.
2007 Uniden America Corporation, Fort Worth, Texas. Contains additional foreign articles. Printed in China.