Color profile: Disabled Composite Default screen Front Cover C:...Exp 7900 series.
Color profile: Disabled Composite Default screen Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ringer Tone and Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Setting the Handset Earpiece Volume . . . . . . . . . . . . . . . . . 8 Included with Your EXP 7900 Series Phone . . . . . . . 3 EXP 7903/7904 Charging Cradle . . . . . . . . . . . . . . . .
Color profile: Disabled Composite Default screen Included with Your EXP 7900 Series Phone batt lo talk talk flash mem status 900 MHz 1 2 abc 3 def 4 ghi 5 jkl 6 mno 7pqus 8 tuv 9wxyz page/find tone 8 oper redial pause m1 m2 chan volume m3 Base Handset Rechargeable Battery AC Adapter Telephone Cord EXP7903/7904 Only: Charging Cradle and Power Supply Also included: • This Owners Manual • Other Printed Material • Precautions and Important Safety Instructions If any of these item
Color profile: Disabled Composite Default screen Controls and Functions 1. talk - answers or places calls 2. */tone - switches to tone dialing in pulse dial mode 3. redial - redials the last number 4. pause - adds a timed pause in a memory dialing sequence 5. talk/batt - LED indicates when phone is in use or the battery is low 6. flash - accesses call waiting (if available) 7. mem - enters or recalls numbers in memory 8. volume - sets both the ringer and earpiece volumes 9.
Color profile: Disabled Composite Default screen Installation Charging the Battery Pack ▼ Low Battery Indicator The rechargeable Nickel-Cadmium battery pack must be fully charged before using your phone for the first time. Before plugging the phone line into your new phone, you must charge the battery for approximately 15-20 hours without interruption. When the battery pack in the handset is low and needs to be charged, the batt LED flashes every 3 seconds.
Color profile: Disabled Composite Default screen 2. Flip the retainer over so the tab is facing up. Desk or Tabletop Installation 1. Plug the AC adapter cord into the 9V DC input jack on the base. 2. Wrap the AC adapter cord inside the molded strain-relief. 3. Slide the retainer back onto the base. 1 3 5 ▼ Mounting on a Standard Wall Plate 2 The phone is designed to be mounted on a standard AT&T or GTE wall plate. 4 1. Plug the AC adapter into the base. 2.
Color profile: Disabled Composite Default screen ▼ Mounting Directly on a Wall 3. Place the AC adapter cord inside the left molded channel cord holder. If you do not have a standard wall plate, you can mount the phone directly on a wall. Before mounting your cordless telephone, consider the following: 4. Plug one end of the long telephone cord into the TEL LINE jack on the base.
Color profile: Disabled Composite Default screen Setting Up Your Phone Raising the Antenna 2. The phone has two ringer tones, each with two volume levels. Press volume again until you hear the ringer tone and volume level you want. Before using your phone, be sure to raise its antenna to the vertical position. ▼ Setting the Handset Earpiece Volume Adjusting Ringer/Volume Controls 1. While you are on a call, press volume . ▼ Ringer Tone and Volume 2.
Color profile: Disabled Composite Default screen Using Your Phone Making and Receiving Calls Handset on Base Handset off Base When the phone rings, remove the handset from the base. Press any key. Answer call (AutoTalk) Make call Hang up Return handset to the base. (AutoStandby) Press talk. 1. Remove the handset from the base and press talk. 2. Listen for the dial tone. 3. Press redial to dial the number. 1. Pick up the handset and press talk . 2. Listen for the dial tone. 3.
Color profile: Disabled Composite Default screen 3. Press the memory location number (0-9) you want to clear. You hear a long beep confirming that you have erased the number. Dialing a Stored Number To dial a phone number stored in memory, press talk, then press mem and the memory location (0-9). Your phone will dial the stored number. NOTE Replacing a Stored Number If you select a memory location that does not have a stored number, the handset will beep rapidly and the phone will not dial.
Color profile: Disabled Composite Default screen Troubleshooting If your EXP 7900 Series cordless telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact your place of purchase or call customer service at (800) 297-1023. Caution: Do not attempt to service this unit yourself. Servicing must be performed by qualified personnel. Problem Suggestion Charge light wont come on when handset is placed in base.
Color profile: Disabled Composite Default screen Back Cover C:...Exp 7900 series.
