uh064sx-2 Operating Guide txp txp mic mic To bring outstanding wireless communication products to people's lives throughout the world.
CONTROL & INDICATORS INCLUDED IN YOUR PACKAGE: • uh064sx Radio (2) • Operating Guide • Belt Clip (2) • • • • TORS Charging Cradle with AC Adaptor NiMH Battery Pack (2) VOX Headset (2) External Speaker Mic (2) OPTIONAL ACCESSORIES • VOX Earset • Carry Case 21 22 23 24 13 14 15 txp mic 1 Antenna 2 PTT(Push-To-Talk) Key 3 Monitor Key 4 Keylock/Call Key 5 Memory/Scan Key 6 Channel/ Transmit Power Key 7 Speaker 8 Headset Jack 9 Select/Power On-Off Key 10 Volume/Select Up Key 11 Volume/Select Down Key 12
GETTING STARTED Uniden does not represent this product to be waterproof. Do not expose this product to Rain or Moisture. BATTERY INSTALLATION Your uh064sx unit uses the included NiMH battery pack for power. The unit can be powered with optional 4 AAA ALKALINE batteries. If you don't use the uh064sx for long periods, Uniden recommend removing the batteries. The uh064sx is designed to retain the previous user settings.
INSTALLING THE CHARGE CRADLE 1. Plug the AC adaptor into the rear of the charge cradle and into the mains power. 2. Place the uh064sx into the charge cradle. The charge light will come on to indicate the unit is charging. 3. Before operating the uh064sx, charge the battery pack for 16 hours. Do not charge alkaline or non rechargeable batteries.
BELT CLIP To attach the belt clip: Slide the belt clip until it snaps into place. To remove the belt clip: To remove the belt clip, press and hold belt clip locker, slide the belt clip at the same time until released. LOW BATTERY ALERT If the battery level becomes low, the battery indicator icon on the display begins flashing. When the batteries in the unit are low, the unit will go into a battery Low mode. The Transmit mode is disabled.
OPERATION POWER ON/OFF 1. Press and hold select/ key to turn the radio on. A channel number will appear on the display. 2. Press and hold select/ key to turn the radio off. VOLUME 1. Press or key to increase or decrease the volume level. ‘VOL’ icon appears on the display while volume is being adjusted. There are 8 volume levels. Level 0 (No Audio) to Level 7 (Maximum Volume). txp ADJUSTING THE KEY BEEPS mic Your radio emits a beep each time one of the keys (except for the PTT key) is pressed. 1.
SELECTING A CHANNEL 1. Press ch/txp key momentarily to activate channel select mode. The displayed channel will flash. 2. Press or key to select the desired channel. txp For your reference a list of the available channels, corresponding frequencies and guidelines for their use is printed on page 12. For Australia, Channels 05 and 35 are reserved for Emergency Calls. 3. Press ch/txp key momentarily to exit channel select mode.
AUTOMATIC SQUELCH FEATURE The uh064sx is equipped with an Automatic Squelch System which shuts off weak transmissions and unwanted noise. MONITOR This feature enables users to listen for weak signals on the current channel at the press of a key. To use monitor: 1. Press mon key. The ‘RX’ icon will flash. 2. Release within 1.5 seconds and the unit exits Monitor mode. 3. Press and hold mon key for 2 seconds for continuous listening.
REPLY DELAY While scanning, the uh064sx stops at a busy channel and receives a transmission. When the received signal is over, the unit will wait for 2 seconds for the return of the signal, otherwise, the radio resumes scanning. TO OPERATE IN DUPLEX MODE (REPEATERS) The Duplex function enables you to access local repeater stations. You can only activate Duplex from CH01-CH08. UHF CB Repeaters are used to retransmit or relay your signal.
CTCSS & DCS (Continuous Tone Coded Squelch System) & (Digital Coded Squelch) CTCSS is a feature that allows a group to talk to each other without hearing other users on the same channel. 1. Press select/ key momentarily to enter CTCSS mode. The current selected CTCSS tone flashes. 2. Press key to select the required CTCSS tone (OFF or 1-38). 3. Press select/ key six times to confirm the selected setting and exit to standby mode.
VOX VOX is the automatic transmitting function by inputting voice into the VOX headset mic without pressing the PTT key. 1. Press select/ key momentarily twice while in standby mode to enter VOX Sensitivity mode. The current selected VOX setting will flash on the display. 2. Press or key to adjust the VOX sensitivity. 1 is the highest sensitivity and 4 is the lowest sensitivity. VOX can be turned off by selecting ‘oF’ icon. 3. Press select/ key five times to confirm the setting and exit to standby mode.
PRIORITY SCAN CHANNEL To set a priority scan channel: 1. Press select/ momentarily four times while in standby mode to enter Priority Scan Channel mode. The current priority channel will be indicated. 2. Press or key to increase or decrease the desired channel number. 3. Press select/ three times to confirm and exit to standby mode. PRI will be displayed when a priority channel has been selected.
UHF CB CHANNELS & FREQUENCIES Please follow these guidelines for channel use in Australia: • Channels 05 and 35 are Emergency Channels. • Channel 11 is a Calling Channel. • Channels 22 and 23 are for telemetry and telecommand applications and TX is inhibited on these channels. General communication is accepted on all other channels with these guidelines: • Channel 40 - road channel (Australia). • Channels 01-08 (and 31-38) are repeater channels. CH No.
CTCSS & DCS Code List (o0) (o1) (o2) (o3) (o4) (13)
WARRANTY UNIDEN UH064SX-2 UHF CB TRANSCEIVER RADIO Limited One Year Warranty Please keep your sales docket as it provides evidence of warranty. Warrantor: Uniden Australia Pty Limited ABN58 001 865 498 Uniden New Zealand Limited. Warranty only available in original country of purchase.
© 2007 Uniden Australia Pty Limited/Uniden New Zealand Limited Printed in China UTZZ01933ZA(0)
