UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page a WDECT 2315+2 Quick Start Guide Wide Band Digital Technology provides the clearest sound and the best privacy.
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page i INSTALLATION & SAFETY Choosing the best location for your phone. When choosing a location for your phone there are a number of appliances the phone should not be near, and areas you should avoid. AVOID Television sets and other electronic appliances AVOID Moisture CHARGE the new phone for 15 - 20 hrs. AVOID Microwave ovens • This symbol indicates important operating and servicing instructions. AVOID moisture Don’t overload the power outlet.
UP409ZH (WDECT2315-2) OM 12/22/05 Start Here! 3:25 PM Page ii QUICK START GUIDE This page is a very condensed version of the Owner’s Manual. It is designed to allow you to get your phone installed and operating as quickly as possible however it does not attempt to explain any of the advanced features of the WDECT2315 series. Installing the Base Unit Route the cord. 1) Connect the AC adapter to the DC IN 9V jack and to a standard AC wall outlet.
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page iii 3) Set the base on a desk or tabletop. Connecting the charger 1) Connect the AC adapter into the charging cradle and to a AC wall outlet. 2) Set the charger on a desk or tabletop. Installing the battery pack • Charge the handset battery pack for at least 15-20 hours before using your new cordless telephone for the first time. • Use only the Uniden rechargeable battery pack (BT-446) supplied with your cordless telephone.
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page iv Charging the handset(s) 1) Place the handset(s) in the main base unit or charging cradle with the keypad facing forward. Recharge your phone on a regular basis by returning the handset to the base after each phone call. 2) Make sure the charge LED illuminates. If the LED does not illuminate, check to see that the AC adapter is plugged in and that the handset makes good contact with the base charging contacts.
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page v CONTENTS INSTALLATION & SAFETY i QUICK START GUIDE ii CONTENTS v GETTING STARTED Controls and Functions Uniden Company Philosophy Welcome Features Checking the Package Contents Terminology Mounting the Base Unit on a Wall Battery Maintenance Installing the Beltclip Headset Installation Display and Icons About the Menu Options Setting up the Menu 1 1 3 3 4 5 5 6 7 8 9 9 10 13 BASICS Making and Receiving Calls Keypad Lock Placing a Call on Hold Redi
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 1 6 2 7 3 4 8 14 9 10 15 11 12 13 18 19 20 21 22 5 16 17 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. Handset Antenna Headset Jack Cover Beltclip Hole Hands-Free Speaker Handset Battery Compartment New Message LED Handset Earpiece LCD Display /del Key /vol/ / Key a. ringer volume control b.
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Main Base Page 2 Charger Base 23 31 24 25 29 26 27 23. 24. 25. 26. 27. 28. [2] Base Antenna Base Charging Contacts charge LED Key TEL LINE Jack DC IN 9V Jack 28 30 29. Charging Contacts 30. charge LED 31.
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page 3 UNIDEN COMPANY PHILOSOPHY To bring outstanding wireless communication products to people’s lives throughout the world. WELCOME Congratulations on your purchase of the Uniden Multi-Handset Cordless System telephone. This unit is different from conventional cordless telephones. When the base unit is connected to AC power and a telephone line, it can support up to 4 handsets.
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page 4 FEATURES Great features of this cordless phone include: • Designed and Engineered in Japan • Wide Band Digital Technology • Multi (4) Handset Capable • Digital Duplex Speakerphone on Handset Advanced Alpha Display Caller ID Features: • Alpha Memory Dialling • POP ID - Caller Name Identification* • 20 Individual Caller Tone Allocation* • 100 Caller ID * Memories with Phonebook • 3 Line Backlit Full Dot Matrix LCD Display with Clock • Maxi-Sound - Extra Lou
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page 5 CHECKING THE PACKAGE CONTENTS Make sure you have received the following items in the package. If any of these items are missing or damaged, contact your retailer. • Base unit (1) • Handset (3) • AC adapter (3) • Rechargeable battery pack (3) • Line adapter (Australia only) (1) • Linecord (1) • Beltclip (3) • Charger (2) Also included: • This Owner’s Manual TERMINOLOGY Throughout this manual, terms such as Standby and Talk Mode are used.
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page 6 MOUNTING THE BASE UNIT ON A WALL You can mount your base directly to the wall. Before doing this, consider the following: • Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. • Mount your phone within distance of a working phone jack. • Make sure the wall material is capable of supporting the weight of the base and handset.
UP409ZH (WDECT2315-2) OM 12/22/05 3:25 PM Page 7 BATTERY MAINTENANCE Battery use time (per charge) Fully charged • Up to 7 hours continuous use. • Up to 10 days when the handset is in the standby mode (up to 15 hours when in DirectLink mode) Recharge your phone on a regular basis by returning the handset to the charger after each phone call. Low battery alert When the batteries are very low and need to be charged, the phone is programmed to eliminate functions in order to save power.
UP409ZH (WDECT2315-2) OM 12/22/05 3:26 PM Page 8 Battery replacement and handling When the operating time becomes short, even after a battery is recharged, please replace the battery. With normal usage, your battery should last about one year. Please contact your place of purchase or the Uniden Parts Department for a replacement battery. • • • • Caution Use only the specified Uniden battery pack (BT-446). Do not remove the batteries from the handset to charge them.
UP409ZH (WDECT2315-2) OM 12/22/05 3:26 PM Page 9 HEADSET INSTALLATION Your phone may be used with an optional headset, the Uniden HS910. To use this feature, insert the headset plug into the headset jack. Your phone is ready for hands-free conversations. Headset is available through Uniden authorized retailers.
UP409ZH (WDECT2315-2) OM 12/22/05 3:26 PM Page 10 ABOUT THE MENU OPTIONS There are 5 main menu options, (DirectLink Mode, Room Monitor, Handset Setup, Global Setup and System Reset) and submenu options. During Global Setup and System Reset, make sure your cordless phone is in standby mode (not in use), and all handsets are within range of the main base unit.
UP409ZH (WDECT2315-2) OM 12/22/05 3:26 PM Page 11 Handset Setup The following submenu options must be set separately for each handset. Submenu name Edit Voice Mail Ringer Tones (Default is Flicker) Distinct. Ring (Distinctive is on) AutoTalk (Default is on) Anykey Answer (Default is on) Banner (True Banner) Key Touch Tone (Default is on) Description Program or delete the voice mail access number (see page 14). Adjusting the ringer tone (tone your phone makes when ringing) (see page 15).
UP409ZH (WDECT2315-2) OM 12/22/05 3:26 PM Page 12 Global Setup If you change one of the Global settings, you change the setting for all additional handsets. Only one handset can change Global settings at a time. Submenu name Day & time Name Tag (POP ID) (Default is on) Insert 0 Dial Mode (Australia only) (Default is tone) Copy Phonebook Description Set the day and time of your display (see page 17).
UP409ZH (WDECT2315-2) OM 12/22/05 3:26 PM Page 13 SETTING UP THE MENU Entering the Menu 1) Press the /del key in standby mode. DirectLink Mode 2) Use /vol/ or /vol/ to move the pointer to a desired main menu (DirectLink Mode, Room Monitor, Room Monitor Handset Setup, Global Setup, and System Reset). Handset Setup 3) Press to select the desired main menu. 4) Use /vol/ or /vol/ to select a desired submenu, and then press to enter. In the submenu, use /vol/ or /vol/ to select an item.
UP409ZH (WDECT2315-2) OM 12/22/05 3:26 PM Page 14 Room Monitor Using Room Monitor This is an example, if you have handset #1 and #2. 1) Enter the Room Monitor menu (see “Entering the Menu” on page 13). To Room Monitor appears. 2) Select the handset you want to monitor by using /vol/ or /vol/ . 3) Press . RoomMonitor appears, and you hear sounds in the room where the handset is installed. 4) To finish the Room Monitor, press or return the handset to the cradle.
UP409ZH (WDECT2315-2) OM 12/22/05 3:26 PM Page 15 Selecting a Ringer Tone 1) Enter the Handset Setup menu, and then the Ringer Tones submenu (see “Entering the Menu” on page 13). Ringer Tones Flicker Clatter There are 10 ringer tones or 10 Polyphonic Tones to choose from.
UP409ZH (WDECT2315-2) OM 12/22/05 3:26 PM Page 16 Setting the Anykey Answer 1) Enter the Handset Setup menu, and then the Anykey Answer submenu (see “Entering the Menu” on page 13). 2) Press /vol/ or /vol/ to select On or Off. 3) Press . You will hear a confirmation tone. Anykey An swe r On Off Setting the True Banner 1) Enter the Handset Setup menu, and then the Banner submenu (see “Entering the Menu” on page 13). 2) Use the number keypad (0-9), , , or /del to enter or edit the name. 3) Press .
UP409ZH (WDECT2315-2) OM 12/22/05 3:26 PM Page 17 Global Setup Setting Name Tag (POP ID) 1) Enter the Global Setup menu, and then the Name Tag submenu (see “Entering the Menu” on page 13). 2) Press /vol/ or /vol/ to change the selection, On or Off. 3) Press . You will hear a confirmation tone. Setting Insert Zero (New Zealand only) 1) Enter the Global Setup menu, and then the Insert 0 submenu (see “Entering the Menu” on page 13). 2) Press /vol/ or /vol/ to change the selection, On or Off. 3) Press .
UP409ZH (WDECT2315-2) OM 12/22/05 3:27 PM Page 18 Setting the Dial Mode (Australia only) 1) Enter the Global Setup menu, and then the Dial Mode submenu (see “Entering the Menu” on page 13). 2) Press /vol/ or /vol/ to change the select, Tone or Pulse (the initial setting is Tone). 3) Press . You will hear a confirmation tone. Dial Mode Tone Pulse Copy Phonebook • If you receive a call or set up the Global Setup menu, the transfer will be canceled.
UP409ZH (WDECT2315-2) OM 12/22/05 3:27 PM Page 19 System Reset De-register the Handset 1) Enter the System Reset menu, and then the Deregister HS submenu (see “Entering the Menu” on page 13). 2) Press /vol/ or /vol/ to select the handset ID to be de-registered from the list, and then press . Deregister HS? appears. 3) Press /vol/ or /vol/ to select Yes. 4) Press . You will hear a confirmation tone. When de-registration is complete, Deregistration Complete appears.
UP409ZH (WDECT2315-2) OM 12/22/05 3:27 PM Page 20 MAKING AND RECEIVING CALLS BASICS • To set Autotalk, see page 15 or to set Anykey Answer see page 16. • The handset microphone is located at the bottom of the handset (see “Controls and Functions” on page 1). Position yourself as near to the handset as possible and speak clearly. • If the line is in use by another handset(s), Line In Use appears in the display of all registered handset’s display, that are not in use.
UP409ZH (WDECT2315-2) OM 12/22/05 3:27 PM Page 21 KEYPAD LOCK The Keypad Lock prevent user from pressing the keypad accidentally. You can still answer calls, and receive page and phonebook locations, and the keypad lock is reactivated after the operation. To lock the keypad Press and hold Keypad Locked appears. until you hear a confirmation tone. If anykey is pressed when keypad is locked, To unlock keypad press & hold * key appears. To unlock the keypad Press and hold again.
UP409ZH (WDECT2315-2) OM 12/22/05 3:27 PM Page 22 REDIALING A CALL The last three phone numbers dialed can be quickly redialed. • If the number exceeds 32 digits, only the first 32 digits are retained in redial memory. • If the redial memory is empty, you will hear a beep. Redialing from Standby Mode < R edi a l1> 8 007 3 034 5 6 1) Press redial/pause in standby mode. 2) Press redial/pause again. Each press of redial/pause will display one of the last three number redialed. 3) Press or speaker.
UP409ZH (WDECT2315-2) OM 12/22/05 3:27 PM Page 23 ADJUSTING THE HANDSET RINGER, EARPIECE AND SPEAKER VOLUME Handset ringer volume Press the volume up key or volume down key (labeled as /vol/ or /vol/ in standby mode to select one of three ringer volume (off, low, or high). Standby Mode - The handset is not in use and has not been pressed.
UP409ZH (WDECT2315-2) OM 12/22/05 3:27 PM Page 24 MUTE MICROPHONE You can temporarily turn off the microphone so that the person you are talking with cannot hear you. 1) Press /del during talk mode (while phone is in use). 2) Press /vol/ or /vol/ to move the pointer to Mute and then . Mute On and appear in the display. To cancel muting, repeat above step again when Mute is set to on, Mute Off appears.
UP409ZH (WDECT2315-2) OM 12/22/05 3:27 PM Page 25 CLARITY BOOSTER If you encounter interference while using your phone, you can manually improve the sound by setting the Clarity Booster to on. This works only when the phone is in use. Talk B Boost On 1) Press /del during talk time (while phone is in use). 2) Press /vol/ or /vol/ to move the pointer to Clarity Boost, and then . Boost On and B appear in the display.
UP409ZH (WDECT2315-2) OM 12/22/05 3:27 PM Page 26 FIND HANDSET If the battery pack is completely drained, the handset will not beep when paging. To locate the handset, press on the base when the base is in standby mode. All registered handsets beeps for 60 seconds, and “Paging” appears on the handset display. To cancel paging, press any key on the handset or on the base.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 27 USING ONE TOUCH VOICE MAIL ACCESS If you subscribe to voice mail service, you can use your phone to access your voice mailbox. The new message LED flashes whenever you have messages waiting in your voice mailbox. Just program the handset with your access number, and you can get your messages at the touch of a button on the handset. (The voice mail service provider will supply you with the access number. This number may be simply a phone number.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 28 PHONEBOOK PHONEBOOK • Your phone has 100 memory locations for Caller ID messages or stored Phonebook numbers. • Selecting a speed dial location where a number is already stored releases the old number’s speed dial setting. The new number will be stored in the speed dial location. • When the memory is full, you will hear a beep and Memory Full appears. You cannot store names and numbers. • The pause key counts as one digit.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 29 6) Distinctive Ring appears. Press /vol/ or /vol/ to move the pointer to one of the Distinctive Ring options, and then press . Distinctive Ring No Selectn Flicker Distinctive ringing will only operate if you subscribe to the Caller ID service. If you choose not to store a Distinctive Ring, simply select the “No Selectn” option. 7) Speed Dial appears. Press /vol/ or /vol/ to move the pointer to select the Speed dial location (10 locations: SPD1-SPD0).
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 30 STEPS FOR ENTERING NAMES AND SPECIAL CHARACTERS Refer to the letters on the number keys to select the desired characters. With each press of a number key ( ), the displayed character appears in the following order: upper case letters first, lower case letters next and finally the number corresponding to the key.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 31 If you make a mistake while entering a name Use or to move the cursor to the incorrect character. Press /del to erase the wrong character and then enter the correct character. To delete all characters, press and hold /del. For example, to enter Movies: 1) When the phone is in standby mode, press 2) Press phonebook. , Store/Edit Name appears. 3) Press 6 once, and then press to move the cursor to the right. 4) Press 6 six times. 5) Press 8 six times.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 32 VIEWING THE PHONEBOOK Your phone stores names/numbers in the phonebook memory locations, and you can search names in alphabetical order. You can view the phonebook even while the phone is in use. 1) Press phonebook. Phonebook :1 00 Search [A- Z/ / ] Store [SE LEC T] If you recall the phonebook during a call, Store [SELECT] will not appear. 2) Press /vol/ , /vol/ , or the number keypad to scroll through the phonebook locations.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 33 MAKING CALLS USING THE PHONEBOOK From Standby Mode 1) When the phone is in standby mode, view the phonebook location to dial (see “Viewing the Phonebook” on page 32). 2) Press is dialed. or 3) To hang up press speaker. The displayed number Movies 0295979035 Beethoven9/SPD1 . From Talk Mode 1) Press or speaker. 2) View the phonebook location to dial (see “Viewing the Phonebook” on page 32). 3) Press .
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 34 EDITING OR ERASING A STORED NAME, PHONE NUMBER, DISTINCTIVE RING, AND SPEED DIAL 1) When the phone is in standby mode, press phonebook. 2) Press /vol/ or /vol/ , or the number keypad to view the phonebook locations (see “Viewing the Phonebook” on page 32). Phonebook :1 00 Search [A- Z/ / ] Store [SE LEC T] a. Editing the Stored Data 1) When the phonebook location to be edited appears, press . Store/Edit Name appears.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 35 CHAIN DIALING The memory locations in the handset are not limited to phone numbers. You can also store a group of numbers (up to 20 digits), that you need to enter once your call connects. This is referred to as Chain Dialing. An example of this is a bank account number. Store the account or special number in one of the phonebook locations. (Refer to “Storing Phone Numbers, Names, Distinctive Rings and Speed Dial” on page 28.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 36 CALLER ID CALLER ID • If you answer a call before the Caller ID message is received (for example, before the second ring), the Caller ID message will not appear. • When the call is received via a telephone company that does not offer Caller ID service, the caller’s phone number and name does not appear. (This includes some international calls.) • When the call is via a private branch exchange (PBX), the caller’s phone number and name may not appear.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 37 2) When you pick up the phone, the display changes to Talk. (AutoTalk feature is set to on). Data errors appear as “ ”. VIEWING THE CALLER ID LIST The Caller ID list stores information for incoming calls - even unanswered calls. You can store 100 of the Caller ID messages and Phonebook locations (including SpeedDials) in total. You can view the Caller ID list during a call or when the phone is in standby mode. 1) Press . The summary screen appears.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 38 DELETING A CALLER ID MESSAGE Deleting Information from the Caller ID List • Once the Caller ID data has been deleted, the information cannot be retrieved. • Standby Mode The handset is not in use and has not been pressed. • Talk Mode The handset is not in the cradle and or speaker has been pressed enabling a dial tone. Talk appears on the display.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 39 USING THE CALLER ID MESSAGE LIST Calling a party from the Caller ID list From Standby mode • You cannot make a call from the Caller ID list if your phone is 21/12 11:20AM connected to a private Jane Smith branch exchange (PBX). 2) Press or speaker. The displayed phone 0295979035 • If a call comes in via a number dials automatically. telephone system that does not offer Caller ID From Talk mode service, no information 1) Press or speaker. is stored.
UP409ZH (WDECT2315-2) OM 12/22/05 3:28 PM Page 40 EXPANDING YOUR PHONE 4 Multi-Handset Expendability EXPANDING YOUR PHONE • To use the WDECT2305, register it to the original base. • Save this manual for detailed operation. • All of the handsets ring when a call is received. [ 40 ] Your phone supports up to 4 handsets (including the handset(s) supplied with your phone). You can now place a fully-featured cordless handset anywhere AC power is available to connect the handset charger.
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 41 REGISTER THE HANDSET If you purchase an extra handset, you need to register the handset to the base before use. Only one handset can be registered at a time. The handset ID for the supplied handset(s) was assigned at the factory, which has #1 or #2 in the display (#2 for models that have two handsets in packaging). When you register additional handset to the base, the handset ID will be assigned.
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 42 USING TWO WAY COMMUNICATION BETWEEN THE HANDSETS ANYWHERE WITHOUT THE BASE (DIRECTLINK) Two handsets can be in Direct Link mode while other handsets are in use. To use this feature, you must enter the two handsets into the DirectLink mode first. To enter the DirectLink mode e See page 13 DirectLink Call 1) When the phone is in the DirectLink standby mode, press (example of DirectLink from handset #1).
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 43 3-WAY CONFERENCING The phone permits 3-way conversations between 2 handsets, and an outside line. 1) During a call, press on another handset to initiate the 3-way conversation. 2) To remove either caller from your conversation, press key on either handset. The other handset will still be connected to the call. INTERCOM/CALL TRANSFER FEATURE If you have one or more extra handsets, you can enjoy an intercom call between handsets.
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 44 Call Transfer Feature 1) During a call, press /transfer/int’com. 2) Select a handset to transfer the call within 10 seconds. (Refer to step 2 in the intercom section on page 43). The call will automatically be placed on hold, and an intercom tone sounds. To cancel the transfer, press or Hold,to tr ans fer Handset #2 Handset #3 speaker on the initiating handset. 3) On the receiving handset, to answer the page, press or /transfer/int’com.
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 45 CHANGING THE DIGITAL SECURITY CODE 1. Perform the “System Reset” menu options (“De-register the Handset” and “Replacing the Base Setting”) for all the handsets you have (see page 19). 2. To register all the handsets do the following steps: 1) Place a handset, one at a time in the base. 2) Registration starts automatically. While registering Handset Registering appears in the display.
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 46 NOTE ON POWER SOURCES Battery replacement and handling When the operating time becomes short, even after a battery is recharged, please replace the battery. With normal usage, your battery should last about one year. Please contact your place of purchase or the Uniden Parts Department for a replacement battery.
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 47 TROUBLESHOOTING If your phone is not performing to your expectations, please try these simple steps first. Symptom The charge LED won’t illuminate when the handset is placed in the cradle. The audio sounds weak and/or scratchy. Can’t make or receive calls. The handset doesn’t ring or receive a page. “Unavailable” appears in the display. Suggestion • Make sure the AC adapter is plugged into the base and wall outlet.
UP409ZH (WDECT2315-2) OM 12/22/05 Symptom Severe noise interference. 3:29 PM Page 48 Suggestion • Keep the handset away from microwave ovens, computers, remote control toys, wireless microphones, alarm systems, intercoms, room monitors, fluorescent lights, and electrical appliances. • Move to another location or turn off the source of interference. The Caller ID does not display. • The handset was picked up before the second ring. • The call was placed through a switchboard.
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 49 INDEX 0-9 3-way conferencing ....................43 20 ring options ..........................15 A Anykey answer............................16 AutoTalk ....................................15 B Banner ......................................16 Battery Preparing and charging ..............iii Replacement and handling ..........46 Beltclip ......................................8 Booster ....................................25 C Caller ID Caller ID service ....
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 50 WARRANTY One Year Limited Warranty Important: Evidence of original purchase is required for warranty service. Warrantor: Uniden Australia Pty Limited A.B.N.
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 51 NOTE [ 51 ]
UP409ZH (WDECT2315-2) OM NOTE [ 52 ] 12/22/05 3:29 PM Page 52
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 53 NOTE [ 53 ]
UP409ZH (WDECT2315-2) OM 12/22/05 3:29 PM Page 54 Additional Handset & Charger Expand Your System! WDECT2305 HANDSET & CHARGER Easily expand your cordless phone system by adding the WDECT2305 Handset and Charger*. The WDECT2305 gives you the mobility you need to stay connected with friends and family.
