ECT R005 OM.
XDECT R005 Accessory Handset Owner's Manual What's in the box? XDECT R005 accessory handset and repeater with charger Battery cover Rechargeable battery pack (BT-694 or BT-694s) Belt clip Desk stand/wall mount bracket Repeater/Charger AC adapter (AAD-041S(M)) If any items are missing or damaged, contact your place of purchase. Never use damaged products! Need Help? Get answers at our website: www.uniden.com.au for Australian model or www.uniden.co.nz for New Zealand model.
Setting Up Your Handset Install the Battery 111 Unpack the handset, battery pack, and battery cover. If the battery cover is already on the handset, press in on the notch and slide the cover down and off. 222 Line up the battery pack connector with the jack inside the handset. (The battery connector only fits one way.) 333 Push the battery pack connector in until it clicks into place. Tug gently on the wires to make sure the battery pack is securely connected.
333 Place the handset in the charger with the display facing forward. The charge light should turn on. If... Try... the charge light does not turn on -- reseating the handset. -- checking the AC adapter connection. Charge the handset completely (about 15 hours) before using it. Registering the Handset The accessory handset will not work until you register it to a base! Registering the handset is a separate process from registering the Repeater/ charger.
Using the Repeater/Charger How it Works The XDECT R005 repeater/charger extends the range of your base in all directions, including up and down. Each handset will automatically connect to the repeater/charger or the base, depending on which signal is stronger. (The handset operates exactly the same way whether it's connected to the base or to the repeater/charger.) Base Coverage Area Handsets in this area always connect to the base.
Registering the Repeater/charger Registering the Repeater/charger is a separate process from registering the handset. You can use the charger even if the handset is not registered. 111 On the base, open the menu and select Register Handset. 222 On the bottom of the repeater/charger, press and hold the registration button until the Link light starts to blink (about 2 seconds). 333 Release the button and wait for the Link light to turn on and steady (this can take about 90 seconds).
Picking the best spot The best spot for the repeater/ charger is as far from the base as possible while still maintaining a good signal, or near the edge of the base’s coverage area. To find the edge of the coverage area: 111 Stand near the base and make a call on the handset. 222 While on the call, carry the handset away from the base towards the general area where you want to put the charger. 333 Watch the signal strength icon on the handset. Make a note where the icon drops from 4 bars to 3 bars.
Wall Mounting the Repeater/charger If you want mount the charger on the wall, you need to adjust the desk stand: 111 Pull the locking tab up and back (see the black arrow in the illustration to the right), and slide the desk stand straight off. 222 Flip the stand over so the locking tabs that say wall are facing the charger with the arrows pointing down. 333 Align the stand with the notches on the charger. 444 Slide the stand onto the notches until it clicks into place.
Important Information Handling Liquid Damage Moisture and liquid can damage your cordless phone. If the handset or repeater/charger is exposed to moisture or liquid, but only the exterior plastic housing is affected, wipe off the liquid, and use as normal. If moisture or liquid has entered the plastic housing (i.e.
Battery Information Fully charged, the battery should provide about 8 hours of talk time and about 7 days of standby time. For best results, return the handset to the cradle after each call to keep it fully charged. Keep an eye on the battery status icon. When the battery gets too low, the handset shows a low battery alert. If you hear a strange beep during a call, check the display: if you see the low battery alert, finish your conversation as quickly as possible and return the handset to the cradle.
Warrantor The warrantor is either Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden Aust”) or Uniden New Zealand Limited (“Uniden NZ”) as the case may be. Terms of Warranty Uniden Aust/NZ warrants to the original retail purchaser only that the XDECT R005 (“the Product”), will be free from defects in materials and craftsmanship for the duration of the warranty period, subject to the limitations and exclusions set out below.
© 2011 Uniden Australia Pty Ltd/Uniden New Zealand Limited Printed in Vietnam UUZZ01208BB(0) ECT R005 OM.
