Owner`s manual

Outdoor LP Gas Barbecue Grill Model No. GBC621C
Contact 1-800-762-1142 for assistance. Do not return to place of purchase.
page no.
7
Operating Instructions
Checking for Leaks
Burner Connections
Make sure the regulator valve and hose
connections are securely fastened to the
burner and the tank.
If your unit was assembled for you, visually
check the connection between the burner
pipe and orice. Make sure the burner
pipe ts over the orice.
WARNING: Failure to inspect
this connection or follow these
instructions could cause a re
or an explosion which can cause
death, serious bodily injury, or
damage to property.
Please refer to diagram for proper
installation.
If the burner pipe does not rest ush to
the orice, please contact 1.800.762.1142
for assistance.
Tank/Gas Line Connection
Make 2-3 oz. of leak solution by mixing one
part liquid dishwashing soap with three parts
water.
Make sure control knobs are off.
Turn LP gas tank ON at valve.
Spoon leak check solution at all “x” locations
If any bubbles appear turn LP gas tank OFF,
reconnect and re-test. If you continue to see
bubbles after several attempts, disconnect LP
gas source and contact 1.800.762.1142 for
assistance.
If no bubbles appear after one minute turn tank OFF, wipe away solution and proceed.
Operating Main Burners
Lighting
1. Open lid. Attempting to light the
burner with the lid closed may
cause an explosion!
2. Make sure there are no
obstructions of airflow to the gas
unit. Spiders and insects can nest
within and clog the burner / venturi
tube at the orifice. A clogged
burner tube can lead to a fire
beneath the appliance.
3. All control knobs must be in the
OFF position.
4. Turn on gas at LP gas tank.
5. Push and turn control knob counterclockwise to HIGH.
6. Press the electronic igniter button and hold for 5 seconds to light burner.
7. If ignition does not occur in 5 seconds, turn burner control knob OFF, wait 5 minutes,
and repeat lighting procedure.
8. If igniter does not light burner, use a lit match secured with the lighting rod provided
to light burners manually. Access the burners through the cooking grid and heat
plates. Position the lit match near side of the burner.
Important: Always use the lighting rod provided when lighting burners with a match.
9. After lighting, observe the burner flame, make sure all burner ports are lit and flame
height matches illustration.
CAUTION: If burner flame goes out during operation, immediately
turn the gas “OFF” and open lid to let the gas clear for about 5
minutes before re-lighting.
Turning Off
1. Turn all control knobs clockwise to the OFF position one at a time.
2. Turn gas off at LP tank.
Initial Use
Before cooking on this grill for the first time, operate the grill for about 15 minutes with
the lid closed and the gas turned on “HIGH.” This will “heat clean” the internal parts and
dissipate odor from the manufacturing processes.
X
X
X
X
X
Main Burners
Gas Valve
with orice
Burner
Venturi
Gas
Connections
Side Burner
Gas Valve
with orice
Gas
Connections
Burner
Venturi
1/2"
12.7 mm
6.4mm
0mm
1/4"
0"
Burner
Main burner proper flame height.
Flame
Installing LP Gas Tank
To operate you will need (1) precision-filled standard grill LP gas tank (20#) with external valve
threads.
Insert LP Gas Tank
Place precision filled LP gas tank into hole in grill body upright so it is arranged for vapor
withdrawal.
Secure LP Gas Tank
Secure tank by sliding tank retainer wire over shoulder of LP gas tank.
Connect LP Gas Tank
Before connecting, be sure that there is no debris
caught in the head of the gas tank, head of the
regulator valve or in the head of the burner and
burner ports.
Connect gas line to tank by turning knob clockwise
until it stops.