UTV-P Product Manual Revision Records Version Revised Content Date 01 Initial release Nov. 12, 2017 02 Update operating instructions Jun. 08, 2019 03 Update address Mar. 20,2020 The manual may be modified without any prior notice.
UTV-P Product Manual Instructions Thank you for choosing our product. Please read the Product Manual carefully before using the product. The manual may contain errors despite all our efforts, and may be subject to change without prior notice. Contact us if you have any questions or suggestion when using the manual. We will try our best to help you resolve the problems in time, and highly appreciate your suggestions. ` Copyright The manual is the property of Unilumin Group Co., Ltd.
UTV-P Product Manual Read the following content carefully to ensure correct use of the indoor LED display products: WARNING! The LED display may be damaged and become irreparable if you ignore the following warnings. 1) Do not place the LED display upside down or throw it during transport and storage. 2) Do not incline, scratch, or crash the LED display during installation. 3) Do not wet or submerge the LED display into water.
UTV-P Product Manual CAUTION! The optimum displaying effect may fail to be achieved if you ignore the following cautions. 1) Wear antistatic gloves when installing or repairing the product. 2) Ensure good ventilation for the LED display when designing the heat dissipation solution. 3) Keep the storage environment of the LED display well ventilated and dry, with a humidity not exceeding 85%.
UTV-P Product Manual Read the following content carefully to ensure correct use of the outdoor LED display products: WARNING! The LED display may be damaged and become irreparable if you ignore the following warnings. 1) Do not place the LED display upside down or throw it during transport and storage. 2) Do not incline, scratch, or crash the LED display during installation. 3) Do not submerge the LED display into water. 4) Do not direct the air outlet of an air conditioner to the LED display.
UTV-P Product Manual CAUTION! The optimum displaying effect may fail to be achieved if you ignore the following cautions. 1) Wear antistatic gloves when installing or repairing the product. 2) Ensure good ventilation for the LED display when designing the heat dissipation solution. 3) Keep the storage environment of the LED display ventilated and dry, with a humidity not exceeding 95%.
UTV-P Product Manual Contents Chapter 1 Product Introduction.......................................................................................9 1.1 Features ...............................................................................................................9 1.2 Product Appearance .............................................................................................9 1.3 Specification ....................................................................................................
UTV-P Product Manual Chapter 6 Instructions for operation under Android System .........................................39 6.1 Use environment ................................................................................................39 6.1.1 Control device access to UTV-P hotspots ...................................................39 6.1.2 Control device and UTV-P access to LAN ...................................................39 6.2 Introduction to software interface features .......................
UTV-P Product Manual 11.7 Other ................................................................................................................69 11.8 Product Warranty Card .....................................................................................70 Contact Information ......................................................................................................
Chapter 1 Product Introduction Chapter 1 Product Introduction The UTV-P series is a new generation of commercial poster LED display product launched by Unilumin. Designed for super light, ultra-thin, high quality and intelligent management. It shows excellent results and supports multiple interface connections. There are many types of installation, and can meet the requirements of the application environment to the maximum. 1.1 Features 1) Ultra-light and ultra-thin, less than 30kg.
Chapter 1 Product Introduction 1.3 Specification Parameter Physical Parameter UTV-P 1.8 Pixel composition UTV-P 2.5 1R1G1B LED type 3-in-1 Black SMD Pixel Pitch 1.8 2.
Chapter 1 Product Introduction 1.4 Scope of Application The UTV-P series products are extensively used for advertisements in public places such as retail brand stores, shopping malls, hotels, churches, airports, theatres, cinemas, company lobbies, high-end clubs, museums, and large conference rooms.
Chapter 2 Installation Guide Chapter 2 Installation Guide 2.1 Out-of-Box Inspection Check whether the packages are damaged. If the packages are intact, check the main components against the shipping list. If any inconsistency is found, contact us in time. The main components include cabinets, signal cable, power cable, USB cable, HDMI cable, maintenance tools and Parts box. For details about the components, refer to the shipping list. 2.2 Introduction of Installation Method 2.2.
Chapter 2 Installation Guide 13
Chapter 2 Installation Guide 2.2.2 Installation of Base Support Base Limit module Support module Bolt Gasket Figure 2-3 Parts 1) 14 Install the limit module.
Chapter 2 Installation Guide M5 Bolt 2) Install the support module M8 Bolt 3) Install the fixed module 15
Chapter 2 Installation Guide 16
Chapter 2 Installation Guide 4) Install the cabinet M5 Bolt 17
Chapter 2 Installation Guide 2.2.3 Vertical Wall Mounted Note: Please install on the wall that can withstand 38KG weight.
Chapter 2 Installation Guide 1) Drill the holes Put the mounting frame close to the wall and adjust the level, make the mark in the hole, take off the mounting frame and drill the hole. Hole 2) Use explosive bolts to fasten the mounting frame to the wall.
Chapter 2 Installation Guide 2.2.4 Horizontal Wall Mount 1. Rotate the cabinet counterclockwise to 90° 2. Installing the retention module at the distance from the edge 500mm, then fasten the cabinet.
Chapter 3 Function Introduction Chapter 3 Function Introduction 3.1 Button Function Before performing control setting on the LED display, confirm that each device is connected correctly. 1. HDMI IN 2. Audio 3. LAN board 8. HDMI OUT 4. USB 5.USB 6. Config 7. Liquid crystal display 9. Power Switch 10.
Chapter 3 Function Introduction 3.2 Display Mode Introduction 3.2.1 Standalone Mode When the poster is used routinely, each poster can operate independently and display different pictures. The poster screen can be segmented into multiple windows by the software editing of the system. It can support video window, picture window, scroll text window, date time window, etc.
Chapter 3 Function Introduction 3.2.2 Replication Mode When multiple posters are routinely connected through HDMI, from left to right the first poster is the controller. In the replication mode, the other entire posters will read the main poster’s information and play the same picture.
Chapter 3 Function Introduction 3.2.3 Extended Mode When multiple posters are routinely connected through HDMI, from left to right the first poster is the controller. Set all posters to extend mode, the posters’ screens will be connected to a large display screen.
Chapter 4 Basic setting Chapter 4 Basic setting UTV-P has completed all settings before shipping, which can be changed via PC if some of the settings need to be changed during use. 4.1 Basic Setting Connect the computer and UTV-P by debugging cable. Time Settings: Click [ Modify ] to set up date and time, or time zone as well. Player Time: Display current time. Uptime: Calculated running time once C6 powered on. Total/Available: View memory utilization.
Chapter 4 Basic setting 2) In Program Management, you can conduct a comprehensive management on programs included in UTV-P, and all programs can be deleted in Program Management regardless of the type and source. 3) Schedule Settings: In Schedule Settings, click [ Add ] to add schedule command, and schedule command can conduct timing settings on contents like play program, sleep, wakeup, reboot, brightness adjustment, media volume, switch to sync/async signal, etc.
Chapter 4 Basic setting 4) Commands can be edited and deleted after completing adding schedule commands.
Chapter 4 Basic setting 4.2 Advanced Settings 4.2.1 Playing Parameters ①LED Resolution The [ Width ] / [ Height ] you input must be equal to or slightly larger than the actual screen resolution.
Chapter 4 Basic setting 4.2.2 Network Setting ①WIFI Check [ WIFI ] in network tab, and input your WIFI login information for [ SSID ] and [ Password ], then click [ Apply ] and [ Refresh ] to complete setting, click [ Details ] to check connection status.
Chapter 4 Basic setting ②WIFI Hotspot Input your [ SSID ] and [ Password ] to use a WIFI Hotspot; [ Band ]: 2.4G or 5G (5G mode will be faster and more reliable if both smart phone and computer support 5G WIFI) [ Channel ]: 14 or 24 choices, to avoid network overload.
Chapter 4 Basic setting ③LAN (Network Cable) 1. [ Automatically Obtain IP Address ] (Default) When you connect your UTV-P’s LAN port to a networked router, UTV-P will automatically obtain an IP address. 2. [ Use Following IP Address ] To use a specific IP address, enter information for [ IP ], [ Subnet Mask ], [ Gateway ], then connect UTV-P LAN port to the router. 3. [ Details ] View network connection information like Status, Mac Address, IP address, etc.
Chapter 4 Basic setting ④4G Check [ 4G ] in network tab, click [ Apply ] and [ Refresh ] to access 4G network, click [ Test Network State ] to check connection status.
Chapter 5 Instructions for operation under Windows System Chapter 5 Instructions for operation under Windows System 5.1 Program Editing Turn on the software, you will see [ LED1 ] in program editing area. Right-click [ LED1 ] to add [ Normal Page ], you can add [ File Window ] in [ Normal Page ], then add [ Image ] and [ Video ] under the [ File Window ] to add media for asynchronous play.
Chapter 5 Instructions for operation under Windows System 5.2 Program Publishing 5.2.1 Publish Program through Direct USB ①In [ Program Editing Area ], after finishing program editing, select the [ Program Page ] that you are going to publish. ②Click [ UTV-P ] and then right-click to choose [ Publish current program to the selected player ], you must rename the program and allow it to finish uploading to fully publish your program.
Chapter 5 Instructions for operation under Windows System 5.2.2 Publish Program through Ethernet Port ①In [ Program Editing Area ], after finishing program editing, select the [ Program Page ] that you are going to publish; ②Click [UTV-P ] and then right-click to choose [ Publish current program to the selected player ], you must rename the program and allow it to finish uploading to fully publish your program.
Chapter 5 Instructions for operation under Windows System 36
Chapter 5 Instructions for operation under Windows System 5.2.3 Publish Program through USB Disk 1. To begin publishing through USB, first insert your USB disk to the PC USB port; Click [ Publish Program to Playboxes ] to extend program publishing window. Note: USB disk should be empty before publishing for best performance. Remove previous updated programs before using it to update or play new programs, so as to avoid any problems. 2.
Chapter 5 Instructions for operation under Windows System ②Choose USB Disk Mode: ●Play program from USB disk (Auto play USB disk content after inserting to UTV-P; and the content won’t be stored in UTV-P) ●Update program from USB disk (Auto play USB disk content after inserting to UTV-P; and the content will be stored in UTV-P) ③Select the drive letter under USB Disk, then right-click to choose [ Publish current program to the selected USB disk ], after publishing program successfully, insert USB disk into
Chapter 6 Instructions for operation under Android System Chapter 6 Instructions for operation under Android System Scan the QR code and download the device control software for Android: 6.1 Use environment When using mobile device control of Android, you need to connect the control device to the hotspot issued by UTV-P, or the control device and UTV-P to connect to the same local area network. 6.1.
Chapter 6 Instructions for operation under Android System 3) Click on the advanced settings, enter the management password 168, enter the management interface: 4) Select the network, check WIFI, enter the LAN account number and password, click on the OK.
Chapter 6 Instructions for operation under Android System 6.2 Introduction to software interface features Open the software, enter the main interface: click Click to refresh, find the terminal. : Access to the quick management interface.
Chapter 6 Instructions for operation under Android System Search Terminal: Find Online UTV-P; Editing program: directly into the program editing interface, the follow-up will introduce the specific operation; Fast connection terminal: When multiple devices are connected, you can view all device status and choose management; Quickly edit programs: quickaccess to saved templates, program editing; Language: You can make changes to the language of the software.
Chapter 6 Instructions for operation under Android System After entering the management interface, there are three main modules: control, program, screenshot: ① Control: basic settings management of equipment; 43
Chapter 6 Instructions for operation under Android System 44
Chapter 6 Instructions for operation under Android System ② Program: Editing and managing the programs that need to be used; All programs that have been played are saved here and can be called directly, or you can edit the program in advance and call it directly if needed.
Chapter 6 Instructions for operation under Android System 6.3 Program Management and Broadcasting 1) Click on the icon in the upper right corner to select ‘Edit Program’. 2) Enter the program management interface, where all the programs that have been played are recorded and can be called directly. Click the lower right icon 46 to add a new program.
Chapter 6 Instructions for operation under Android System 3) Set the screen size: size refers to the total resolution of the display, UTV-P1.8 resolution is 320 x 1080, UTV-P2.
Chapter 6 Instructions for operation under Android System 5) Set the screen 1 size, click blank to cancel the selection, click on the add window, while adjusting the resolution below; 6) After the screen adjustment, click on the screen to add playback material 48
Chapter 6 Instructions for operation under Android System 7) Add footage, click on the icon in the upper right corner to send the show 8) Select the device that needs to change the program, click again, and finish sending the program.
Chapter 7 Instructions for operation under iOS System Chapter 7 Instructions for operation under iOS System Search the App Store for LED Assistant and download the installation. 7.1 Use environment When using mobile device control of iOS, you need to connect the control device to the hotspot issued by UTV-P, or the control device and UTV-P to connect to the same local area network. 7.1.
Chapter 7 Instructions for operation under iOS System 3) Click on the advanced settings, enter the management password 168, enter the management interface: 4) Select the network, check WIFI, enter the LAN account number and password, click on the OK.
Chapter 7 Instructions for operation under iOS System 7.2 Introduction to software interface features Open the software, click on the icon to switch languages, there are Chinese, English, Japanese three choices.
Chapter 7 Instructions for operation under iOS System LED control: adjust the brightness of the screen, color temperature, volume and other states; Terminal Setting: enter the password 168, you can change the basic parameters of the display (advanced functions, please use with caution); Information: You can view the terminal information and change the name of the device. 7.
Chapter 7 Instructions for operation under iOS System 2) Click on the icon to create a new program, according to the playback content selection type of pictures / videos, picture text, single lines of text, multi-line text, etc.
Chapter 7 Instructions for operation under iOS System 4) Multi-screen settings: after clicking back in the previous step, modify the window coordinates and resolution below 5) After the window adjustment, the footage management.
Chapter 7 Instructions for operation under iOS System 6) Go into the add edith interface.
Chapter 7 Instructions for operation under iOS System 7) After the material is added, click on the upper right corner to send the program; 57
Chapter 8 Daily Maintenance Chapter 8 Daily Maintenance 8.1 Daily Maintenance 1) The screen surface (including PC glass) is strictly prohibited from being hit and scraped by other sharp objects, do not put product in high temperature, high humidity and strong magnetic environment to avoid direct sunlight. 2) Do not use strong oxidizer or other washing products to wipe PC glass. 3) Check the power line regularly, keep the screen well grounded, and keep the screen working in a stable power environment.
Chapter 9 Troubleshooting and Component Replacement Chapter 9 Troubleshooting and Component Replacement 9.1 Common Faults and Troubleshooting Methods Failure phenomenon Fault description Troubleshooting method 1. confirm whether the power supply is normal Failure in lighting up Open the power switch, the screen is unresponsive 2. the flicker of the signal indicator, such as no flicker, confirms whether the screen is powered 3.
Chapter 9 Troubleshooting and Component Replacement 1. confirm that the U disk is able to read and U disk cannot update content U disk cannot write normal data and check the format of load the video or the U disk (default FAT32) picture 2. confirm whether the format of the video is correct and the format of the picture 1. confirm that the screen is in the same LAN with the computer WiFi work PC can't connect anomaly to the screen 2. check if the screen is dropped 3.
Chapter 9 Troubleshooting and Component Replacement 9.2 Replacement of main Components 9.2.
Chapter 9 Troubleshooting and Component Replacement 9.1.2 Replacement of Power Supply Step 1 2 Picture Description Remove the rear cover Remove the screws Power supply cover plate Find the faulty power 3 supply and replace with a new one.
Chapter 10 Packaging Transportation and Storage Chapter 10 Packaging Transportation and Storage 10.1 Packaging The UTV-P series products would be packaged with flight case. Figure10-1 Package 10.2 Transportation The cabinets must be packaged before transportation. The product shall not be placed upside down or horizontally, and must be protected against the wind, rain, direct sunlight, and corrosive liquid during transportation. The stacking layers shall not exceed three layers for plywood cases. 10.
Chapter 11 After-Sales and Warranty Chapter 11 After-Sales and Warranty 11.1 The Warranty Terms This clause applies to LED display products purchased directly from Unilumin and under warranty. Any products not purchased directly from Unilumin are not applicable to these Terms. 11.2 Warranty Period The warranty period is in accordance with the contract, please save the warranty card or other valid documents. 11.
Chapter 11 After-Sales and Warranty customs clearance fees incurred in returning the repaired products or equipment. Unilumin is not responsible for damage and loss caused by transportation and packaging. 3）Engineers On-site service for product quality problems: For quality problem stipulated in Article 4 and necessary, Unilumin will provide engineer on-site service free of charge.
Chapter 11 After-Sales and Warranty storage, etc. 8） Use the product outside the product parameters, including but not limit to lower or higher voltage conditions, extreme or excessive power surges, and inadequate power conditions. 9） During the installation process, defects, malfunctions or damages caused by non-compliance with technical guidelines, instructions or precautions. 10） Under normal conditions, natural loss of brightness and color. 11） The product lacks necessary maintenance.
Chapter 11 After-Sales and Warranty 3) b) Customer mailing instructions: c) Provide a brief description of the fault of the repaired product (can be attached to the surface of the device) d) Packing list (including contract order number, type and quantity of equipment to be repaired) e) Return receipt information (company name, delivery address, consignee and contact details, etc.
Chapter 11 After-Sales and Warranty turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
Chapter 11 After-Sales and Warranty le brouillageest susceptible d'encompromettre le fonctionnement. “This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.” « ce matériel est conforme aux limites d'exposition aux rayonnements rf de ic énoncés dans un autre environnement.
Chapter 11 After-Sales and Warranty 11.8 Product Warranty Card Product Warranty Card Warranty Order No.
Contact Information Contact Information Shenzhen Headquarters Headquarter Address: 112 Yongfu Rd., Qiaotou Village, Fuyong Town, Baoan District, Shenzhen 518103 China Pingshan manufacturing center: 6 Lanjing North Road, Pingshan District, Shenzhen 518118 China. Daya Bay manufacturing center: Longsheng Fifth Road, western Daya Bay, Huiyang District, Huizhou, China. Telephone (switchboard): +86-755-29918999 Fax: +86-755-29912092 Website: www.unilumin.
Contact Information Customer Service Center Tel: +86-(0)755-89318939(direct line） 29918999-8806（extension） E-mail: Customer-service@unilumin.com Hotline: 400-677-3888 UNILUMIN USA LLC USA HQ Address: 254W 31st St. 12th Floor, New York, NY 10001 E-mail: service@unilumin-usa.com Tel: 001 844 263 3675 EUROPEAN SERVICE CENTER Address: Parellaan 28, 2132 WS, hoofddorp, the Netherlands E-mail: euro-support@unilumin.com sales@unilumin.com Tel:：+31(0)20 214 9657 UNILUMIN UK CO.
Contact Information E-mail: sales@unilumin.com UNILUMIN GERMANY GMBH Address: Raiffeisenstr. 30 - 70794 Filderstadt E-mail: info@unilumin.de Tel: +49 711 38967 898 UNILUMIN AUSTRALIA PTY LTD (BUSINESS IN OCEANIA) Address: Level 1, Trak Centre, 443/449 Toorak Road, Toorak, VIC 3142 Tel: +61 3 9006 8960 +86-755-29918999 +61 3 9827 8374 E-mail: amer-support@unilumin.com sales_au@unilumin.
