Instructions / Assembly

ManualsBrandsUnimax ManualsElectricalFixed TV Mount for 0 in. - 39 in. Flat Panel TVs

CAUTION Capacity: 44lbs (20kg). Use with products heavier than capacity may result

in instability causing possible injury

Read through ALL instructions before commencing installation.

If you have any questions about this product or issues with installation contact

the customer services help line before returning this product to the store.

See www.avfgroup.com/unimax for instruction video.

AVF Group Ltd. Hortonwood 30, Telford, Shropshire, TF1 7YE, England

AVF Incorporated 3187, Cornerstone Drive, Eastvale, CA 91752, USA

www.avfgroup.com

44lbs

20kg

STOP

CUSTOMER SERVICES HELP LINE NUMBER:

+44 (0)1952 670009 (UK)

1-800 667 0808 (USA)

465088 rev00

Summary of content (8 pages)

PAGE 1
465088 rev00 ## CAUTION Capacity: 44lbs (20kg). Use with products heavier than capacity may result in instability causing possible injury STOP Read through ALL instructions before commencing installation. If you have any questions about this product or issues with installation contact the customer services help line before returning this product to the store. See www.avfgroup.com/unimax for instruction video.
PAGE 2
1 Boxed Parts You will not need all these parts, so expect there to be some left over depending upon the specification of your TV. A B - x1 Wall Bracket Adaptor - x10 D2 Spacer - x4 Spacer (Red) E1 - x4 M4 Adaptor E2 - x4 M5 Adaptor - x2 Stand-off Wall Fixings: Parts to attach to the wall (type of wall will determine which fixings you require). TV Fixings: Parts go on the back of the TV (specification of your TV will determine which ones you require - see section 9).
PAGE 3
Determine Correct TV Screw Size Choose from the TV Fixings selection. You need to determine which length and diameter of screws fits your TV. To determine the correct screw diameter, try screwing (F2), (F6), (F10) & (F14) into one of the fixing holes on the back of the screen until you find the one that fits. Note the thread size and ensure you use the appropriate diameter screws.
PAGE 4
5 Marking Wall For Drill Points Decide the position of your wall bracket and using a pencil lightly draw a straight, level line approx 220mm long. approx 220mm Use the Wall Bracket (A) as a template and position it on your wall. Ensure the bracket lines up with the line you have previously drawn and mark the two DRILL POINTS with a pencil. Drill point A Drill point Pencil Line 6 Planning & Preparation Determine the wall type that you have (i.e. Brick/Stud/Plasterboard/Sheetrock).
PAGE 5
7 Install Wall Fixings Use the correct fixings for your wall type. Mixing fixing types may be required for installations that span different wall types. DO NOT OVER TIGHTEN SCREWS. Solid Wall A G I K L M Solid 75mm (3") Concrete O A M L Ø10mm (25/64") Remove dust from holes N Lubricate screw thread with soap 12.5mm (½") Max Plasterboard / Sheetrock Min supporting surface specification:- ½” thick plasterboard/drywall, mounted on 1½” x 3½” wood stud at 16" centres.
PAGE 6
8 Hanging The TV Vertical Line Guide Marks Hanger Guide Tabs Rotate your TV so that the guide marks on the hanger are vertical. Next slide your TV down so that the hanger goes between the two guide tabs on the wall bracket. Ensure the hanger is fully engaged and rotate clockwise until your TV is level. If cables from your TV prevent the TV resting against the wall then an alternative hanger configuration will be required (See Section 9). TV must be parallel to wall. Use spacers / stand-offs as shown.
PAGE 7
9 Alternative Hanger Configurations Wall Space Alternative Wall spacings of 20mm, 30mm & 40mm can be achieved using the spacer / screw combinations listed in this section.
PAGE 8