465091 rev00 STOP ## Read through ALL instructions before commencing installation. If you have any questions about this product or issues with installation contact the customer services help line before returning this product to the store. See www.avfgroup.com/unimax for instruction video. CUSTOMER SERVICES HELP LINE NUMBER: +44 (0)1952 670009 (UK) 1-800 667 0808 (USA) 121lbs 55kg AVF Group Ltd.
Assembly Overview Fit Screen Hangers to TV Fitting the Wall Bracket Hanging the TV Retain all packaging in case the bracket needs to be returned. Contents may vary from photography/ Illustrations. You will not need all these parts, so expect there to be some left over depending upon the specification of your TV. This product is intended for indoor use only. Use of this product outdoors could lead to failure and personal injury.
Index 1 Measure the TV fixing holes Width and Height Flat to wall only 2 3 4 5 6 7 8 Fit Screen Hangers to TV Assemble Positioning Template Determine Bracket Hole Centres Marking Wall For Drill Points Fitting the Wall Bracket Fitting the Wall Bracket Covers Hanging the TV Tilt Position only 9 Choose Tilt 10 Assemble Positioning Template 11 Determine Bracket Hole Centres 12 Fit Tilt Brackets to TV 13 Marking Wall For Drill Points 14 Fitting the Wall Bracket 15 Fitting the Wall Bracket Covers 16 Hangi
Tools Recommended Ø5.5mm (7/32") Masonry Ø10mm (25/64") Masonry Stud Finder Ø3.
TV Screws, Reducers and Spacers M4 45mm 25mm 16mm J x8 M4 M4 G1 x4 G2 x4 G3 x4 E1 x12 45mm 25mm 16mm H x4 M5 M5 I x4 K x4 E2 x4 M5 G4 x4 G5 x4 G6 x4 M6 M6 L x2 M x4 N x4 O x2 45mm 25mm 16mm F1 x4 M6 G7 x4 G8 x4 G9 x4 M8 M8 P x2 S 45mm 25mm 16mm F2 x4 M8 G10 x4 G11 x4 G12 x6 F3 x4 Q x2 R T
Remove the Wall Bracket Covers and keep for step 7 or 15 Wall bracket covers A1 & B1 are removed in the same way.
1 Measure the TV fixing holes Width and Height Flat X 200mm to infinity TV Fixing Holes Tilt X 200mm to infinity Flat Y 100mm to infinity Tilt Y 100mm to 400mm ! If width X is less than 200mm or height Y is less than 100mm STOP installation now and contact the customer help line You are provided with 4 diameters of TV fixing screws, M4, M5, M6 and M8. Determine the screw diameter that fits and remember for step 2 or 12.
2 Fit Screen Hangers to TV Flat to Wall only Once you have established which screw diameter you need for your TV you will need to choose which wall spacing you require. Check the back of your TV and use the OPTION that fits your TV. Please see page opposite for more details.
OPTION 1 12mm Wall Space Top Fixings M4 M5 Bottom Fixings M6 M8 G1 G4 G7 F1 F2 F3 C C M4 G10 C M5 M6 M8 G1 G4 G7 F1 F2 F3 C D D G10 D D OPTION 2 20mm Wall Space Top Fixings M4 M5 G2 M6 M8 G8 G5 F1 Bottom Fixings M4 G11 G2 F3 F2 M5 M6 G8 G5 F1 M8 F2 G11 F3 C C C C D D D D E1 E1 E1 E1 E1 E1 E1 E1 OPTION 3 40mm Wall Space Top Fixings M4 M5 M6 G6 G3 F1 Bottom Fixings M8 G9 F2 M4 G12 F3 M5 M6 G6 G3 F1 M8 G9 F2 G12 F3 C C
3 Assemble Positioning Template Flat to Wall only U1 U2 4 Determine Bracket Hole Centres Flat to Wall only Lay the template on the back of the TV and follow the instructions below. C Place the top row of holes on template U1 over hangers C. Mark off the top fixing centres The centre line of the template U2 represents the centre of your TV. Top row holes Line up with top of the screen.
5 Marking Wall For Drill Points Before marking the wall, determine the wall type that you have (i.e. Solid Wall/ Dot & Dab/ Plasterboard/ Wood Stud/Metal Stud). Ensure the drilling area is free from mains services (Gas/Electric/Water). Flat to Wall only Represents the top of your TV. T Represents the centre of your TV. Use your template to mark two points on the wall that correspond with the top fixing centres of your TV. Represents the bottom of your TV.
6 Fitting the Wall Bracket Flat to Wall only Use the correct fixings for your wall type. Mixing fixing screws may be required for installations that span different wall types. DO NOT OVER TIGHTEN SCREWS. Solid Wall Dot & Dab 10mm (25/64") 10mm (25/64") 75mm (3") 108mm (41/4") 5.5mm (7/32") Remove dust from holes 40mm (19/16") 40mm (19/16") MAX gap If gap is above 40mm (19/16) use plasterboard fixing method Remove dust from holes 12.
Plasterboard Metal Stud Wood Stud 18mm (3/4") 18mm (3/4") R 18mm (3/4") R R R P 40mm (19/16") MIN gap Self drilling 3mm (1/8") Remove dust from holes 3.5mm (9/64") 75mm (3") i H ii Ensure hole is in the middle of the wood stud S Use Plasterboard Fixing H Use Plasterboard Fixing H iii Self P drilling A+B Turn until secure do not over tighten J x2 Self P drilling A+B J N J L O O J Lubricate screw thread with soap A+B O Only one fixing will be in the wood stud.
7 Fitting the Wall Bracket Covers Flat to Wall only On wall bracket covers A1 & B1 are 3 retaining tabs. These locate onto 3 retaining lips on wall brackets A & B and lock the wall bracket covers in position.
8 Hanging the TV Flat to Wall only Hanging the TV is a two person job. Present hangers C (on the back of the TV) to the opening on brackets A & B. Slide down and across into place. Ensure both hangers are fully engaged. If cables from the TV prevent the TV resting against the wall then an alternative hanger configuration will be required (see section 2). TV must be parallel to wall. Use spacers / stand-offs as shown in section 2.
9 Choose Tilt Tilt Position only You can choose between 2 different tilt positions, either 4° or 8°.
10 Assemble Positioning Template Tilt Position only U1 U2 11 Determine Bracket Hole Centres Tilt Position only Lay the template on the back of the TV and follow the instructions below. Place the top row of holes on template U1 over top TV fixing holes. Mark off the top fixing centres The centre line of the template U2 represents the centre of your TV. Top row holes Line up with top of the screen.
12 Fit Tilt Brackets to TV Tilt Position only Once you have established which screw diameter you need for your TV you will need to choose which wall spacing you require. Check the back of your TV and use the OPTION that fits your TV. Please see page opposite for more details.
OPTION 1 12mm Wall Space Top Fixings M4 M5 Bottom Fixings M6 M8 G1 G4 G7 F1 F2 F3 W W M4 G10 W M5 M6 M8 G1 G4 G7 F1 F2 F3 W W W G10 W W OPTION 2 20mm Wall Space Top Fixings M4 M5 G2 M6 G5 F1 Bottom Fixings M8 G8 M4 G11 G2 F3 F2 M5 W W W E1 E1 E1 E1 F2 W M8 G8 G5 F1 W M6 F3 W E1 G11 W W E1 E1 E1 OPTION 3 40mm Wall Space Top Fixings M4 M5 M6 G6 G3 F1 Bottom Fixings F2 M8 G9 M4 G12 M5 G6 G3 F1 F3 M6 M8 G9 F2 G12 F3 W W
13 Marking Wall For Drill Points ! Tilt Position only Use the marks on the top row that you made in step 11 and make the same marks on the bottom row. You will use the marks on the bottom row to make 2 pencil marks on the wall. Before marking the wall, determine the wall type that you have (i.e. Solid Wall/Dot & Dab/ Plasterboard/Wood Stud/Metal Stud). Ensure the drilling area is free from mains services (Gas/Electric/Water). Represents the top of your TV.
Next, use the Wall Brackets A and B as a template and position them over the appropriate PENCIL MARKS you have made, so that the mark is in the middle of the CENTRAL HOLE of the Wall Bracket. Ensure the bracket is level and mark the three DRILL POINTS with a pencil. Repeat for other bracket. Drill six 3mm pilot holes and select appropriate fixings (see section 14) A B PENCIL MARK CENTRAL HOLE PENCIL MARK Represents the centre of your TV.
14 Fitting the Wall Bracket Tilt Position only Use the correct fixings for your wall type. Mixing fixing screws may be required for installations that span different wall types. DO NOT OVER TIGHTEN SCREWS. Solid Wall Dot & Dab 10mm (25/64") 10mm (25/64") 75mm (3") 108mm (41/4") 5.5mm (7/32") Remove dust from holes 40mm (19/16") 40mm (19/16") MAX gap If gap is above 40mm (19/16) use plasterboard fixing method Remove dust from holes 12.
Plasterboard Metal Stud Wood Stud 18mm (3/4") 18mm (3/4") R 18mm (3/4") R R R P 40mm (19/16") MIN gap Self drilling 3mm (1/8") Remove dust from holes 3.5mm (9/64") 75mm (3") i H ii Ensure hole is in the middle of the wood stud S Use Plasterboard Fixing H Use Plasterboard Fixing H iii Self P drilling A+B Turn until secure do not over tighten J x2 Self P drilling A+B J N J L O O J Lubricate screw thread with soap A+B O Only one fixing will be in the wood stud.
15 Fitting the Wall Bracket Covers Tilt Position only On wall bracket covers A1 & B1 are 3 retaining tabs. These locate onto 3 retaining lips on wall brackets A & B and lock the wall bracket covers in position.
16 Hanging the TV Tilt Position only Hanging the TV is a two person job. Present hangers C (on the back of the TV) to the opening on brackets A & B. Slide down and across into place. Ensure both hangers are fully engaged. If cables from the TV prevent the TV resting against the wall then an alternative hanger configuration will be required (see section 12). Use spacers / stand-offs as shown in section 12.
Removing the Wall Bracket Covers Should you want to remove the wall bracket covers please follow the steps below.
