AC-2000 .USER GUIDE Version Eng-1.00 Copyright 2000 By Union Community Co., LTD.
AC-2000 User Guide Version Date Description Firmware Version 1.00 2016-12-06 -Initial Release 10.61.00-000.02 UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.
AC-2000 User Guide 3 Admin (Administrator) - The administrator can access to the terminal menu mode. He/she has the authority to add/modify/delete terminal users and to change the operating environment by changing settings. - If there is no registered administrator in the terminal, anybody can access to the terminal menu and change settings. It is recommended that more than one administrator will be necessarily registered in the terminal.
AC-2000 User Guide Table of Contents .................................................................................................... 2 ............................................................................................................. 3 Table of Contents.................................................................................................... 4 1. Before Getting Started ................................................................................
AC-2000 User Guide 1. Before Getting Started 1.1. Safety Notes Warning Do not operate the terminal with wet hands, and pay attention not to let any Keep the terminal away liquid such as water enter from inflammables. inside the terminal. → Otherwise, it may → Otherwise, malfunction cause a fire. or electric shock may be caused. Do not disassemble, repair Do not allow children to or remodel the terminal at touch the terminal your disposal. carelessly.
AC-2000 User Guide 1.2. Product Details Status LED FP Sensor Card Input 1.3. LED signals displayed during operation Blue Power Green Door Blue On: Normal Flickering: Under Bluetooth communication Green On: Door Open Off: Door Close Off: Normal Flickering: Case Open or Pending register the Mobile Admin App ※ The LED may light on simultaneously in some cases. (Ex. Red and Blue flicker) Red Alarm Red UNIONCOMMUNITY Co., Ltd.
AC-2000 User Guide 1.4. Buzzer guide announced during operation Ppik When button or card is operated - If the button is pressed or if the terminal reads the card - If your finger may be released because your fingerprint has been successfully entered Ppibik When failure If authentication fails or the user’s input is wrong When success If authentication is successful or if the current user finishes settings Ppiririk 1.5.
AC-2000 User Guide 8 Precautions subject to your fingerprint status The availability of the fingerprint may vary depending on your fingerprint status. This product consists of a fingerprint recognition system and cannot recognize the damaged or unclear fingerprints. They should be registered using a password. If your hands are dry, you can blow your breath on the system to operate it more smoothly. For children, too small or unclear fingerprints may be difficult or impossible to use.
AC-2000 User Guide 9 2. Product Description 2.1. Product Features Access control system using the network (LAN) - The fingerprint reader communicates with the authentication server using a UTP cable and TCP/IP protocol. This terminal can be applied to the existing LAN network and has easy expandability. It ensures a fast speed by 10/100 Mbps Auto Detect and facilitates management and monitoring via the network.
AC-2000 User Guide Various registration and authentication methods There are a total of four registration and authentication methods for general users. Before registering users or administrators, you should determine how to register and authenticate. FP Fingerprint Registration Fingerprint Authentication Card Card Registration Card Authentication M.
AC-2000 User Guide 2.2. Configuration Diagram 2.2.1. Standalone Use (Access) DC12V Adapter (Lock+, Lock-, Monitor) Electrical Lock 2.2.2. Connecting the PC server (Access, T&A, Food Service Control) TCP/IP TCP/IP Internet / WAN / LAN TCP/IP TCP/IP TCP/IP TCP/IP UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.
AC-2000 User Guide 2.3. Product Specification ITEM SPEC CPU 32Bit RISC CPU(400MHz) REMARK 64M DDR2 RAM MEMORY 32M NOR FLASH Fingerprint Sensor Optical Authentication Speed Less than 1 second Scan Area / Resolution 14.8 * 17.9mm / 500 DPI FRR / FAR 0.1% / 0.
AC-2000 User Guide 13 3. Environment Setting 3.1. Checkpoints before environment setting 3.1.1. Run UNIS-B Plus (Mobile App) Visit the App store on your Smartphone and install the Mobile App ‘UNIS-B Plus’. And click on the UNIS-B Plus icon installed to run program. After initializing for more than 2 seconds, the intro menu screen will automatically be displayed. UNIONCOMMUNITY Co., Ltd.
AC-2000 User Guide 3.1.2. Add Terminal When selecting [Add] in the upper right corner of [Terminal List], the Terminal Select screen will be displayed. Select the Terminal you want to register then go to the Terminal Search screen to find out the Terminal Registration Guide. When you opened the Temper Switch on the back of device, place your finger on the fingerprint input window and wait for about 5 seconds to operate and register the Terminal. UNIONCOMMUNITY Co., Ltd.
AC-2000 User Guide 15 3.1.3. Administrator Menu Entry When pressing the [View] button on the screen [Terminal List], and the following screen will appear to ask the User ID and Password. Even if there is no registered administrator in the terminal, user can access device without input ID and Password. If there is registered administrator in the terminal, user can access device by attempting authentication methods pre-defined.
AC-2000 User Guide 3.2. User Management 3.2.1. Add User When pressing the [Add] button on the main screen [User Management], and the following screen will appear. Enter the user information to register on [Add User] screen. When you complete input the user information, select [Save] button in the upper right corner. If the user information is normally entered, the terminal will be ready for card or fingerprint input.
AC-2000 User Guide 3.2.3. Modify User Select the user you want to modify on [User Management] screen, and the screen goes to the User Detail. After changing the user information except for ID, press [Save] button on the screen to save the changes, and also the screen may show the waiting status for the additional authentication when it is required. When the modification is completed, the screen returns to [User Management] screen. UNIONCOMMUNITY Co., Ltd.
AC-2000 User Guide 18 3.3. Terminal Configuration 3.3.1. Settings via UNIS-B Plus When pressing [Setting] button in the lower right corner of screen, the following screen will appear. To modify the existing Terminal setting, press [Edit] button in the upper-right corner of screen to enter the edit mode. When the modification of terminal setting is completed, press the [Save] button to save changed values and return to the main screen. ▶ Buzzer volume Set the buzzer sound volume of the terminal.
AC-2000 User Guide 19 ▶ DHCP Use Set whether to use static IP. ▶ Terminal IP Set the terminal IP. ▶ Server IP Set the server IP when used in conjunction with a UNIS server. ▶ Subnet mask Set the subnet mask value of the terminal. ▶ Gateway Set the gateway value of the terminal. ▶ Port Number Set the port of the UNIS server. (Default: 9870) ▶ Firmware version The device's firmware version and BLE firmware version are displayed.
AC-2000 User Guide 20 3.3.2. Terminal IP settings via Terminal Finder Before connecting AC2000 to UNIS server program, you may want to change it to another IP or other terminal ID. In this case, you need a separate program. The location is Program Files -> UNIS -> Patch folder and it is called Terminal Finder Program. With this program, you can search all the buddy devices in the same network and change the network settings (Terminal IP, Server IP, and Terminal ID etc.
AC-2000 User Guide 21 5) Select the device to change the setting. It is highlighted and the current setting value is displayed. UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro, Songpa-gu, Seoul, 05836, Republic of Korea Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.
AC-2000 User Guide 22 6) Modify the network value 7) To enhance security, you can change the password before clicking the [Apply] button. The default password is 0842650. This password can be changed. You can also use the lock option if you do not want to change the network settings again by the UDP search method. If Warning and lock options are set, it may not be possible to configure by using Terminal Finder program.
AC-2000 User Guide 23 4. How to use the terminal 4.1. Authentication 4.1.1. Fingerprint authentication When you place a fingerprint on the fingerprint sensor, the sensor lights up and the fingerprint is input. Do not remove your finger until the fingerprint sensor is completely turned off. 4.1.2. Card authentication Place the card on the card input of the terminal. 4.1.3.
AC-2000 User Guide 24 5. Problem solution 5.1. When Fingerprint Authentication has failed or pended ▶ If the terminal operates 1: N (server) authentication in network mode and the server is used for business or personal use, the recognition rate and authentication time may take a long time due to the server load. Please build a private server. ▶ Check your fingers or sensor for scratches or foreign objects, and wipe them off any foreign objects.
AC-2000 User Guide 25 FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions : (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules.
