AC-2100.User Guide Version Eng-1.00 Copyright 2000 By Union Community Co., LTD.
AC-2100 User Guide 2 < Terminology Description > z Admin, Administrator - As a user who can access using terminal menu mode, the administrator has rights to change the operating environment through registration/modification/deletion of terminal users. - In case no registered administrator is available, anyone can access the terminal menu to change a particular setting. Therefore, it is recommended to have at least one administrator.
AC-2100 User Guide imitation fingerprints produced using rubber, paper, film and silicone. UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topix Bldg. 44-3 Bangi-dong Songpa-gu Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.
AC-2100 User Guide Table of Contents Table of Contents.................................................................................................... 4 1.2. Terminal Component Name .................................................................... 7 1.3. Information on Button Required during Operation............................ 7 1.4. Information on LED Signal Displayed during Operation.................... 8 1.5. Information on Screen Displayed during Operation........................... 8 1.6.
AC-2100 User Guide 5 3.8.1. System Configuration ......................................................................... 49 3.8.2. Card Reader Setting ........................................................................... 49 3.8.4. Wiegand Output Setting ..................................................................... 52 3.8.5. Terminal Initialization ......................................................................... 53 4.2. In Case of Operating as [1.T&A Ctrl]..........................
AC-2100 User Guide 1. Check before Device Use 1.1. Cautions for Safety z Warning Do not operate the device with wet hand, and do not let liquid such as water to flow into the device. -> It may cause device failure or electric shock. Do not place the device near fire. -> It may cause fire. Do not disassemble, repair Do not let children play or modify the device with the device. -> without permission.
AC-2100 User Guide 1.2. Terminal Component Name 1.3.
AC-2100 User Guide - Change to office leave/work outside mode - At menu mode, F4 used as [ENT] or move to right [Æ] button used as [ENT] button if pressed down for longer than 2 seconds: [F4~] 1.4. Information on LED Signal Displayed during Operation ● Power source Red Light on: Normal Light on and off: Cover open ● Door Green Light on: Door open Light off: Door closed 1.5.
AC-2100 User Guide 2009/08/25 16:58 2009/08/25 16:58 - Fingerprint input failure In case the finger is removed too early before the fingerprint is entered - Unregistered card input - In case 1:N authentication is attempted when authentication priority is SN and a user with 1:N authentication permission is not available in the terminal - Passback failure 2009/08/25 16:58 2009/08/25 16:58 - In case processing is difficult during server authentication because too many authentication requests are made
AC-2100 User Guide - When upgrading terminal program (Do not switch off terminal power while this message is displayed.) 2009/08/25 16:58 1.6. Information on LCD Icon Displayed during Operation Server connection state : LAN cable not connected : LAN cable connected but not connected to server program : Connected to server program Door open/closed : Door closed : Door open Reading card : Disappears 1 second after a card is read 1.7.
AC-2100 User Guide 11 If possible, use the index finger and enter fingerprint as if you are making a thumbprint. Just touching a finger to the fingerprint input window is not the proper way for registration/input. The proper way is to touch the center of fingerprint on the fingerprint input window. z If possible, use the fingerprint of the index finger for input. With the index finger, a more accurate and stable fingerprint can be entered. z Check whether the fingerprint is clear or it has wound.
AC-2100 User Guide 12 ¾ If your hand is too dry, breathe into it for a while to ensure smooth operation. ¾ In case of children, fingerprint may be too small or weak to use. It is necessary to register the fingerprint every six months. ¾ In case of seniors, registration may be difficult if fingerprint has excessive fine wrinkles. ¾ It is recommended to register at least 2 fingerprints. UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topix Bldg.
AC-2100 User Guide 13 2. Product Introduction 2.1. Product Features z Access control system using network (LAN) - As communication between fingerprint recognition device and authentication server is done using UTP cable and TCP/IP protocol, existing local area network can be used for good scalability. 10/110 Mbps auto detect provides fast speed and allows easy management and monitoring through a network.
AC-2100 User Guide nearly limitless processing is possible. UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topix Bldg. 44-3 Bangi-dong Songpa-gu Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.
AC-2100 User Guide z Provides various registration and authentication methods There are 4 registration and authentication methods available for general users. The registration and authentication method must be chosen before registering a user or administrator.
AC-2100 User Guide 2.2.2. Connection with PC server (Access, Time & Attendance and Meal Service Management) TCP/IP TCP/IP TCP/IP Internet / WAN / LAN TCP/IP TCP/IP TCP/IP Fingerprint Recognition Server (Static IP) UDB Server Database (MDB or MSSQL) Remote Administrator Program (User and Terminal Setting Management) Meal Service Management Program Time/Attendance Control Program UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topix Bldg.
AC-2100 User Guide 2.3. Product Specifications Classification Specification CPU 32Bit RISC CPU(266MHz) Remarks 8M SDRAM MEMORY 4M FLASH Fingerprint Sensor Optical Authentication Speed Within 1 second Scan Area / Resolution 13 * 15mm / 500 DPI FRR / FAR 0.1% / 0.001% TCP/IP RS-232 Communication Port RS-485 Wiegand In/Out Temperature / Humidity -20 ~ 50 / Lower than 90% RH LCD 128 X 64 Graphic LCD SIZE 92.3mm * 169.9mm * 39.
AC-2100 User Guide 3. Environment Setting 3.1. Items to Check before Setting Environment 3.1.1. Entering Menu If [F2] button is pressed for longer than 2 seconds, the following administrator authentication screen is displayed. Input Admin card or fingerprint [ESC] If administrator authentication with card or fingerprint according to the registered authentication method succeeds, the system enters the menu as shown below. 1.User 2.Network 3.Option 4.Terminal Info 5.Ext Function 6.
AC-2100 User Guide After checking the setting value, press [ENT] button to continue setting. To move to the upper menu during setting, press [ESC] button. In case that the [←][↑][↓][→] buttons are the only buttons displayed ( [ESC] and [ENT] buttons are not displayed ), pressing down [F1] button for longer than 2 seconds replaces [ESC] button function while pressing down [F4] button for longer than 2 seconds replaces [ENT] button. 3.1.3.
AC-2100 User Guide dip switch back to the OFF state. UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topix Bldg. 44-3 Bangi-dong Songpa-gu Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.
AC-2100 User Guide 3.2. Menu Configuration 1.User 1. Add 2. Delete 3. Modify 4. Add admin 5. Delete All 2.Network 1. Terminal ID :NS/SN/NO/SO 2.IP Address 3. Server IP 1. Application 0. Access Ctrl 1.T&A Ctrl 2.Meal Ctrl 3.Option When setting as 0 or 1 2.
AC-2100 User Guide 4.Terminal Info T-ID=0001 Ver=10.50.00 Application=Access Language=ENG Verify Mode=SN Network Type=Static Mac-Address=000265101234 IP Address=192.168.0.3 Gateway=192.168.0.1 Subnet Mask=255.255.255.0 Server IP=192.168.0.2 Svr-Port=2201 Card Reader=RF|SC|Wiegand CDR Version= Card Format=0 1:1 Level=3 1:N Level=4 All Admin=0 All User=0 Max User=100 1:N User=0 1:N FP=0 MAX 1:N FP=100 All FP=0 MAX FP=100 All Log=0 Max Log=5,119 5.Ext Function 1. Lock Terminal 2. Read Card No. 6.
AC-2100 User Guide 5. Initialize 1. Init Config 2. Delete Log 3. Init Terminal UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topix Bldg. 44-3 Bangi-dong Songpa-gu Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.
AC-2100 User Guide 3.3. User Control 3.3.1. User Registration If “1.User” in the main menu is selected, the following screen is displayed. 1. Add 2. Delete 3. Modify 4. Add Admin 5. Delete All [ESC] [↑] [↓][ENT] To register a new user, select “1.Add”. User ID [NEW] ID : 0001 [←] [↑] [↓] [→] Enter the ID of a new user to be registered and press down [F4] button for a longer period of time.
AC-2100 User Guide <1:1 Level> 0123456789 [ESC] [↑] [↓][ENT] Recommended setting: ‘0’ This menu determines the authentication level for each user to be registered. The authentication level for each registered user can be set differently by changing this value. If this value is set as ‘0’, authentication is done using 1:1 authentication level set at the terminal rather than the authentication level for each user. After the completion of setting, press [ENT] button to continue setting.
AC-2100 User Guide is recommended. 3.3.1.2. Registration with “2. Card” Both registration and authentication are made only using card. ◆ At default screen [F2~]Æ [1.User] Æ [1.Add] Æ User ID [F4~] Æ [2.Card] Æ Card reading ◆ Place a card to be registered. To cancel registration and escape, press [ESC] button. When registration is completed, the system returns to “1. Add”. Up to 3 trials can be made should the registration fail.
AC-2100 User Guide 27 For the registration of a user, fingerprint registration (Refer to Registration with “1. FP”) is done after card registration is completed (Refer to Registration with “2.Card”). UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topix Bldg. 44-3 Bangi-dong Songpa-gu Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.
AC-2100 User Guide 3.3.2. User Deletion ◆ At default screen [F2~] Æ [1.User] Æ [2.Delete] Æ User ID [F4~] ◆ If “1.User” is selected by pressing [1] button in the main menu, the following screen is displayed. 1. Add 2. Delete 3. Modify 4. Add Admin 5. Delete All [ESC] [↑] [↓][ENT] Select [2.Delete] to delete a user. This is an item that deletes a user registered in the terminal. After entering the ID of a user to be deleted, press down [F4] button for a longer period of time.
AC-2100 User Guide Input ID [MOD] ID : 0001 [←] [↑] [↓] [→] After entering the ID of a user to be modified, press down [ENT] button for a longer period of time. Modification can be made without distinguishing general user and administrator. If the ID of an unregistered user (or administrator) is entered, the LCD message “Unregistered ID” is displayed and the buzzer sound for failure is heard. Afterwards, the system moves to the menu at the time of selecting “1.Add”.
AC-2100 User Guide Please try again Reenter the same fingerprint. Be sure to note that you must remove the finger from the fingerprint input window before you make the second fingerprint input attempt. When registration is completed, the system returns to “1.Add” selection screen. Up to 3 trials can be done should the registration fail. The following are the LCD messages displayed during the registration process.
AC-2100 User Guide 3.3.4.2. User Registered with “2.Card” 1. Add FP 2. Change CARD 3. Add CARD [ESC] [↑] [↓][ENT] Select [1] to add fingerprint, [2] to change card and [3] to add card. [1] In case of selecting Add FP: Refer to [2] In case of selecting Add FP of 3.3.3.1. [2] In case of selecting Change CARD Press [ESC] button to cancel change. After the card is placed, the “Processing is completed.
AC-2100 User Guide 3.3.4. Administrator Registration ◆ At default screen [F2~] Æ [1.User] Æ [4.Add Admin] Æ Administrator ID [F4~] ◆ Select “1.User” at the main menu. 1. Add 2. Delete 3. Modify 4. Add Admin 5. Delete All [ESC] [↑] [↓][ENT] Select [4.Add administrator. Admin] to register an ID : 0001 [←] [↑] [↓] [→] After entering the ID of an administrator to change, press down [F4] button for a longer period of time.
AC-2100 User Guide Delete All? 1.Yes 2.No [ESC] [↑] [↓][ENT] Select [1] to delete all users and [2] to cancel deletion. After selecting “1.Yes” to answer the above confirmation question, all users including administrators are deleted. Therefore, special caution needs to be taken before using this function. When the deletion process is completed, the buzzer sound for success is heard and the system returns to menu at the time of selecting “1.Add”. 3.4. Network Setting If “2.
AC-2100 User Guide 0.NS 1.SN 2.NO 3.SO [ESC] [↑] [↓][ENT] Select [0] for NS, [1] for SN, [2] for NO, and [3] for SO. This is an item that determines the authentication priority between a terminal and the network server. The default value is ‘1.SN’. Authentication procedures for each mode are shown below. NS If the server is connected, authentication is processed at the server. If the server is disconnected due to network failure, authentication is processed at the terminal.
AC-2100 User Guide 0: Static 1:DHCP [ESC] [↑] [↓][ENT] Select [0] to acquire static IP and [1] to acquire dynamic IP. This item selects a type for connecting a terminal to a server. The default value is ‘0’ (Static IP). Select [0] if a static IP is acquired from the connected server and [1] if a dynamic IP is acquired from the DHCP server existing in the network. After carefully entering the input value, press [ENT] button to continue setting.
AC-2100 User Guide < Gateway > 192.168.000.001 [←] [↑] [↓] [→] After moving to the position of a digit to change using [←][→] button, change the value using [↑][↓] button. The gateway IP address of the network which the terminal is connected to is entered. After carefully entering the value, press down [F4] button for a longer period of time to continue setting. 3.4.3. Server IP Setting ◆ At default screen [F2~]Æ [2.Network] Æ [3.Server IP] ◆ 3.4.3.1. Server IP Setting < Server IP > 192.168.000.
AC-2100 User Guide 3.5. Option Setting 3.5.1. Application Setting If [3.Option] is selected at the main menu, the following screen is displayed. 1. 2. 3. 4. Application Verify Option Set Doorlock Sound Control 5. LCD Setting 6. Time Setting Select [1] to set the operation mode of the terminal. [ESC] [↑] [↓][ENT] ◆ At default screen [F2~] Æ [3.Option] Æ [1. Application] ◆ 0. Access Ctrl 1.T&A Ctrl 2.
AC-2100 User Guide displayed during the time period in setting. Even if authenticated as office leave mode by pressing [F4] button, the mode is switched back to office start mode after authentication is completed to provide convenience in the time & attendance control. After setting , the identical method is used to set . As shown in the following example, these hours must be overlapped.
AC-2100 User Guide If [3.Option] is selected at the main menu, the following screen is displayed. 1. 2. 3. 4. Application Verify Option Set Doorlock Sound Control 5. LCD Setting 6. Time Setting Select [2.Verify Option] to set the default authentication method of the terminal. [ESC][↑][↓][ENT] 3.5.2.1. ID Display Option Setting upon Authentication Success ◆ At default screen [F2~] Æ [3.Option] Æ [2.Verify Option] ◆ 0.None 1.UserID 2.
AC-2100 User Guide After selecting a setting value, press [ENT] button to finish authentication method setting and move to the upper menu. 3.5.3. Door Setting If [3.Option] is selected at the main menu, the following screen is displayed. 1. 2. 3. 4. Application Select [3.Set Doorlock] for door setting. Verify Option Set Doorlock Sound Control 5. LCD Setting 6. Time Setting [ESC][↑][↓][ENT] 3.5.3.1. Door Open Duration Setting ◆ At default screen [F2~] Æ [3.Option] Æ [3.
AC-2100 User Guide 0.None 1.Normal Open 2.Normal Close [ESC][↑][↓][ENT] Default setting: ‘0’ - ‘0.None’: In case door status is not checked - ‘1.Normal Open’: In case of dead bolt type or automatic door (In case lock monitoring is open when the door is locked) - ‘2.Normal Close’: In case of strike type (In case lock monitoring is close when the door is locked) Select ‘0’ for no setting, ‘1’ for dead bolt type or automatic door and ‘2’ for strike type.
AC-2100 User Guide 3.5.4. Volume Setting If [3.Option] is selected at the main menu, the following screen is displayed. 1. 2. 3. 4. Application Select [4.Sound Control] to set volume. Verify Option Set Doorlock Sound Control 5. LCD Setting 6. Time Setting [ESC][↑][↓][ENT] 3.5.4.1. Voice Volume Setting ◆ At default screen [F2~] Æ [3.Option] Æ [4.Sound Control] ◆ 012345 [ESC][←][→][ENT] Default setting: ‘3’ This option sets the volume level during voice guidance.
AC-2100 User Guide 3.5.4.3. Cover Open Alarm Setting ◆ At default screen [F2~] Æ [3.Option] Æ [4.Sound Control] Æ [ENT] Æ [ENT] ◆ Case Open Alarm 1.Yes 2.No [ESC][↑][↓][ENT] Default setting: ‘1.Yes’ This option determines whether to issue a warning after the terminal cover is opened. An alarm is issued for ‘1’ setting and no warning for ‘2’ setting. After selecting a setting value, press [ENT] button to move to the upper menu. 3.5.5. LCD Setting If “3.
AC-2100 User Guide Press [ENT] button to continue setting. 3.5.5.2. LCD Brightness Setting 0.Low 1.Medium 2.High [ESC][↑][↓][ENT] Default setting: ‘1’ This option sets the brightness of the terminal LCD light. Select ‘0’ for dim light and ‘2’ for bright light. After selecting a setting value, press [ENT] button to move to the upper menu. 3.5.6. Current Time Setting If “3.Option” is selected at the main menu, the following screen is displayed. 1. 2. 3. 4.
AC-2100 User Guide current menu. 3.6. Terminal Information Inquiry ◆ At default screen [F2~] Æ [4.Terminal Info] ◆ If “4.Terminal Info” is selected at the main menu, the following screen is displayed. All environment setting values can be checked in order. T-ID=0001 Ver=10.50.00 Application=Access Language=ENG Verify Mode=SN Network Type=Static The setting values in the following table can be checked in order by scrolling up and down using [↑][↓] key.
AC-2100 User Guide MAX 1:N FP All FP MAX FP The maximum number of fingerprints allowed for registration in a terminal (100) In case there are 50 registered users and each of them registered 2 fingerprints, the total number of registered fingerprints is 100.
AC-2100 User Guide 1.Yes 2.No [ESC][↑][↓][ENT] If ‘1.Yes’ is selected, the door opens. ※ To use this function, “Allow administrator access” item must be checked in the terminal option of the server program. After selecting a setting value, press [ENT] button to move to the upper menu. 3.7.2. Card Number Inquiry ◆ At default screen [F2~] Æ [5. Ext Function] Æ [2.Read Card No.
AC-2100 User Guide value of Door_Monitor_0 port is changed. In such a case, the pre-set pop-up message saved in the server is displayed. The sensor monitor1 port uses the same port as the door monitor pin. Therefore, if MenuÆ3.OptionÆ3.Set DoorlockÆ is set to ‘1’ or ‘2’, this port is set to ‘0.None’ under any conditions. If is set to ‘1’ or ‘2’, the menu to select port state transmission option is displayed.
AC-2100 User Guide 3.8.1. System Configuration 3.8.1.1. User ID Digit Setting ◆ At default screen [F2~] Æ [6.Device] Æ [1.System Config] ◆ 2345678 [ESC][←][→][ENT] Default setting: ‘4’ This option sets the length of user ID. A user ID consisting of 2~8 digits is allowed and it must be of identical length to the one registered in the server program. If a 6-digit ID ‘000075’ is registered in the server program, this item is set to 6.
AC-2100 User Guide to ‘1’ in case of reading data from a specific block of smart card. The server sets the detailed card format. ▶ If the card reader type is set to ‘0’, the card number display type can be changed by selecting . 0.Hexa 1 1.Hexa 2 2.Decimal 1 3.Decimal 1 [ESC][↑][↓][ENT] Default setting: ‘0’ This menu designates a type for displaying a card number that was read.
AC-2100 User Guide 3.8.3.2. 1:N Level Setting <1:N Level> 3456789 [ESC][←][→][ENT] Default setting: ‘4’ This is the menu that sets the authentication level in case of using only fingerprint input without ID input. This function is used to locate the corresponding fingerprint by comparing the fingerprint entered in the fingerprint input window with the fingerprints saved in the terminal database.
AC-2100 User Guide If this menu is set to ‘1.Enable’, a checking is performed during the registration process to determine whether a new fingerprint is already registered. This prevents the same fingerprint from being registered again as a new user ID. After selecting a setting value, press [ENT] button to continue setting. 3.8.4. Wiegand Output Setting ◆ At default screen [F2~] Æ [6.Device] Æ [4.Wiegand] ◆ 0.None 1.26bit 2.34bit 3.
AC-2100 User Guide After entering a setting value, press down [F4] button for a longer period of time to move to the upper menu. 3.8.5. Terminal Initialization If [5.Initialize] is selected after selecting “6.Device” at the main menu, the following selection menu is displayed. 1. Init Config 2. Delete Log 3. Init Terminal [ESC][↑][↓][ENT] Select [1] to initialize setting values, [2] to initialize authentication records, and [3] for factory reset. 3.8.5.1.
AC-2100 User Guide the system moves to the upper menu. 3.8.5.3. Factory Reset ◆ At default screen [F2~] Æ [6.Device] Æ [5.Initialize] Æ [3. Init Terminal] ◆ 1.Yes 2.No [ESC][↑][↓][ENT] Select [1] to initialize, and [2] to cancel. All data are deleted and the terminal enters into a factory reset state. If initialization is completed successfully, the buzzer sound for success is heard and the terminal is rebooted. UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topix Bldg.
AC-2100 User Guide 4. How to Use Terminal 4.1. In Case of Operating as [0.Access Ctrl] - Set as Menu Æ 3.Option Æ 1. Application Æ [0.Access Ctrl] 4.1.1. Authentication Mode - Authentication is done after changing to a desired authentication mode such as F1, F2, F3 and F4 by pressing the function keys. In case of authenticating without pressing any function key, authentication with access mode is done automatically.
AC-2100 User Guide F1 2009/08/25 16:58 When you place the finger on the fingerprint sensor, the fingerprint input window is lighted in red along with ppik” sound. Leave the finger until the light is switched off. ▼ 2009/08/25 16:58 Upon authentication success, the voice message “You are authorized” is heard and the success message is displayed on the LCD screen. ※ Error message: The following message along with the voice message “Try it again” is displayed.
AC-2100 User Guide 2009/08/25 16:58 In case of trying to authenticate during a time not allowed for access even though the registration is valid ▶ If a user registered with [Card and FP] places the card on the default screen, “ppik” sound is heard and the following additional fingerprint input procedure is required for authentication. 2009/08/25 16:58 The fingerprint input window is lighted along with the voice message “Please enter your fingerprint”.
AC-2100 User Guide by pressing [F1] key or authentication is done without mode change for hours not set as office start/leave time. 4.2.2. Fingerprint Authentication - Change time & attendance mode by pressing the function keys. - Enter fingerprint. 4.2.3. Authentication Using Card - Change time & attendance mode by pressing the function keys. - Place card. 4.3. In Case of Operating as [2.Meal Ctrl] - Set as Menu Æ 3.Option Æ 1. Application setting Æ [2.
AC-2100 User Guide 59 - In case of attempting authentication without pressing the menu selection key, authentication is done automatically with [Menu 1]. UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topix Bldg. 44-3 Bangi-dong Songpa-gu Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.
