AC-1000 .User Guide Version Eng-1.01 Copyright 2007 By Union Community Co., LTD.
VIRDI AC 1000 User Guide 2 < Glossary > z Admin, Administrator - As a user who can enter into the terminal menu mode, he/she can register/modify/delete terminal users and change the operating environment by changing settings. - If there is no administrator for a terminal, anyone can change the settings, so it is recommended to register at least one administrator.
VIRDI AC 1000 User Guide Table of Contents < Glossary > .................................................................................................2 Table of Contents ..........................................................................................3 1. Before use.................................................................................................6 1.1. Safety precautions .......................................................................6 1.2. Terminal description ........
VIRDI AC 1000 User Guide 4 3.4.8. Server port settings....................................................................27 3.5. Option settings................................................................................27 3.5.1. Application mode settings ..........................................................27 3.5.1.1. [0]: Access Control.............................................................27 3.5.1.2. [1] Time Attendance control ...............................................28 3.5.1.3.
VIRDI AC 1000 User Guide 5 4.3. Meal control ....................................................................................48 4.3.1. Meal classification......................................................................48 4.3.2. Card authentication ....................................................................48 4.3.3. Password authentication ............................................................48 UNION COMMUNITY CO.,LTd. 3Fl.
VIRDI AC 1000 User Guide 1. Before use 1.1. Safety precautions z Warning Handling with wet hands or allowing liquid to flow into it is not advised. -> It may cause an electric shock or damage Do not place a fire source near the unit. -> It may cause a fire. Do not disassemble, repair, or modify the unit. -> It may cause an electric shock, fire or damage. Keep out of reach of children. -> It may cause an accident or damage.
VIRDI AC 1000 User Guide 1.2. Terminal description LCD icon: Terminal operation state - LAN: Server connection status - DOOR: Door open/close status - CARD: Card data is read Card Reading Area LCD display window : Display character message for all the Function Key Ten-key Speaker 1.3. Button description Function key Access mode T&A mode Cafeteria mode Å F1 Start Menu 1 Å F2 Leave Menu 2 Å F3 Outside Menu 3 Å F4 Return Menu 4 Enter menu after pressing over 2sec.
VIRDI AC 1000 User Guide 1.4.
VIRDI AC 1000 User Guide 07/08/25 PM 4:58 - There is no response from the server during the authentication process. - Network to server is disconnected during the authentication process. - There is no user registered on the terminal or no connection to the server, so it is trying to connect. 07/08/25 PM 4:58 - Ready status for card data input 07/08/25 PM 4:58 - A registered user tried authentication when entry/exit is not allowed. 07/08/25 PM 4:58 - Waiting for server authentication.
VIRDI AC 1000 User Guide 1.6. Voice information during operation “You are authorized” Authentication is successful “Please try again” Authentication is failed 1.7.
VIRDI AC 1000 User Guide 2. Introduction 2.1. Features z Access control system using LAN - Communication between the terminal and authentication server is done through d TCP/IP protocol, so an existing LAN can be used as it is. It guarantees network-based administration and monitoring as well as easy expansion, high reliability, and higher speed. z Simple and fast authentication process.
VIRDI AC 1000 User Guide 2.2. Configuration 2.2.1. Network configuration Network Server (Authentication Server) UTP UTP Switch Hub UTP LET UTP 6410 Tx Rx 641 Tx Rx 1 Tx Rx 1 3 Tx Rx 2 Tx Rx 1 2 4 Tx Rx 1 Tx Rx 2 2 3 4 5 6 7 8 9 10 11 12 2 2 641 1 2 3 2 1 643 UTP UTP Tx Rx 1 2 64231 2 3 4 5 6 643 2 Tx Rx 1 1 2 3 Tx Rx 2 4 5 7 6 8 9 10 11 12 1 3 4 WAN TCP/IP UTP 2.2.2. Standalone configuration Door Lock AC-1000 UNION COMMUNITY CO.,LTd. 3Fl.
VIRDI AC 1000 User Guide 2.3. Specifications Item Spec CPU 32Bit RISC CPU Remark 8M SDRAM Memory Authentication speed Communication Port 2M FLASH (Default) User: 10,000 Log: 20,000 4M FLASH (Option) User: 20,000 Log: 98,000 <0.2 sec.
VIRDI AC 1000 User Guide 3. Environment settings 3.1. Check items before setting the environment 3.1.1. Entering menu The following screen appears when the [ENT] button is pressed for over 2 sec. 1. User 2. Network 3. Option 4. Terminal Info 5. Ext Function 6. Device Press [0] to view menus not shown in the LCD window. If a number corresponding to the menu required is pressed (ex.
VIRDI AC 1000 User Guide 3.1.3. Save environment settings Press the [DEL] button in the main menu to save environment settings and the following screen appears: Save? [Y=1/N=2]: Press [1] to save changes. If not, press [2]. ¾ If there are no changes made to the settings, “Save?” does not appear, and the initial screen appears. ¾ If there is no input for a certain period of time while setting the environment, the settings process will finish. If there are changes made to the settings, “Save?” appears.
VIRDI AC 1000 User Guide 3.2. Menu configuration 1. User 1) Add 2) Delete 3) Modify 4) Add Admin 5) Delete All 2. Network 1) Terminal ID 2) Mode [NS/SN/NO] 3) Network Type [Static IP/DHCP] 4) IP Address 5) Subnet Mask 6) Gateway 7) Server IP 8) Server port 3. Option 1. Application - 0 = Access - 1 = Time Attendance - 2 = Cafeteria 1. T&A mode 2.
VIRDI AC 1000 User Guide 4. Terminal Info Terminal ID =0001 Version =10.01.00 Application=Access Language=ENG Mode=NS Network Type=Static(1) Mac-Address=000265101111 I IP Address =192.168.0.3 Gateway =192.168.0.1 Subnet Mask =255.255.255.0 Server IP =192.168.0.2 SVR Port =2201 Card Reader =RF Max User =10416 All User =0 All Admin =0 All Log =0 Max Log =20479 Dip Switch=000000 5. Ext function 1. Lock Terminal 2. Read Card No. 6. Device setting 1. System Config 2.
VIRDI AC 1000 User Guide 3.3. User account 3.3.1. User registration Press the [1] button in the main menu to select “1.User,” and the following screen appears:. 1. Add 2. Delete 3. Modify 4. Add Admin 5. Delete All Press [1] to register a new user. User ID [NEW] ID : _ _ _ _ Enter a new user ID, and press [ENT]. If the entered ID is already used, you will hear an error tone and the screen will go to the previous menu. If not, the following authentication method selection screen appears: 1.RF 2.
VIRDI AC 1000 User Guide 3.3.1.2. “2. ID&PW” registration Password registration and password authentication for a user . ◆ [ENT] Æ [1] Æ [1] Æ User ID + [ENT] Æ [2] Æ Input password + [ENT] Æ Input same password + [ENT] ◆ < Input PW > PW : _ _ _ _ _ _ _ _ Input password. Password should be 1~8 characters in length. Press [ENT] to input the password. < Confirm PW > PW : _ _ _ _ _ _ _ _ Input the same password once more for verification. If you hear three short beeps, registration is successful.
VIRDI AC 1000 User Guide 3.3.1.5. “5. ID&PW|RF&PW” registration RF-Card and password registration, ID input and password authentication or card and password authentication ◆ [ENT] Æ [1] Æ [1] Æ User ID [ENT] Æ [9][3] Æ Place the card Æ Input password + [ENT] Æ Input same password + [ENT] ◆ In this case, a card is used instead of ID for authentication. This is helpful to users who have difficulty inputting their ID. After Card registration (refer to “1.
VIRDI AC 1000 User Guide 3.3.3. Modify User ◆ [ENT] Æ [1] Æ [3] Æ User ID + [ENT] Æ Select changing menu Æ Change value ◆ In the main menu, press [1] to select “1. User” to see the following screen: 1. Add 2. Delete 3. Modify 4. Add Admin 5. Delete All To Modify a user, press [3]. Input ID [MOD] ID: _ _ _ _ Enter the user’s ID to Modify, and press [ENT]. When changing an ID, there is no difference between a user and an administrator.
VIRDI AC 1000 User Guide 3.3.3.2. “2. ID&PW” user 1. Modify PW To change passwords, press [1]. To cancel it, press [DEL]. Press the [1] button to change the passwords PW:_ _ _ _ _ _ _ _ Input new password. Password should be 1~8 characters in length. Press [ENT] to input the password. < Confirm PW > PW:_ _ _ _ _ _ _ _ Input the same password once more for verification. Press [ENT] to confirm the password.
VIRDI AC 1000 User Guide 3.3.4. Administrator registration ◆ [ENT] Æ [1] Æ [4] Æ Admin ID + [ENT] ◆ In the main menu, press [1] to select “1.User” and press [0] to view menus not shown in the LCD window. And the following screen appears: 1. Add 2. Delete 3. Modify 4. Add Admin 5. Delete All For administrator registration, press [4]. ID : _ _ _ _ Enter the administrator ID to register and press [ENT].
VIRDI AC 1000 User Guide 3.4. Network settings In the main menu, press [2] to select “2.Network” to see the following screen. When the setting is chosen, press [ENT] to move to the next setting. 3.4.1. Terminal ID settings ◆ [ENT] Æ [2] ◆ < Terminal ID > ID : 00000001 This ID is unique for each terminal and used by an authentication server to distinguish each terminal. The default is ‘00000001’. It should be identical to the door ID set in the server program, and its length should be 1~8 characters.
VIRDI AC 1000 User Guide - NO mode: select [2]. Even though a user is registered in the terminal, authentication is done through the server in any event. Depending on the number of terminals, the number of users, or network conditions, each different mode can be used flexibly, but if there are more than 10 terminals connected to the server for simultaneous authentication or there are frequent network problems, it is recommended to use SN authentication (setting ‘1’).
VIRDI AC 1000 User Guide 3.4.5. Subnet mask settings < Subnet Mask > 255.255.255. 0 Press [DEL] to delete an old value and enter the new value. If the subnet mask is ‘255.255.255.0’, enter as below: [2] [5] [5] [2] [5] [5] [2] [5] [5] [0] Press [ENT] to move to the next setting. 3.4.6. Gateway settings < Gateway > 192.168. 0. 1 Press [DEL] to delete an old value and enter the new value. If the gateway IP address is ‘210.98.100.
VIRDI AC 1000 User Guide 3.4.8. Server port settings < Server port > Num : 2201 Press [DEL] to delete an old value and enter the new value. As the port number of the authentication server, the default is ‘2201’. Special care is required when changing this number because the corresponding number in the server should also be changed. If the server port is ‘2201’, enter as below: [2] [2] [0] [1] Once the network setting is complete, press [ENT] to return to the main menu. 3.5. Option settings 3.5.1.
VIRDI AC 1000 User Guide 3.5.1.2. [1] Time Attendance control Default time can be set to Start/Leave/Out/Back. After authentication, the terminal display mode can be automatically changed to programmed operation mode. If is set as the operation mode, over 40 sub modes can be defined. < Start Time > 00:00-00:00 If time setting is not necessary, Set as ‘00:00-00:00’.
VIRDI AC 1000 User Guide 3.5.1.3. [2] Meal (Cafeteria) Service control 00:00-00:00 If time setting is not necessary, Set as ‘00:00-00:00’. If time is set from 07:00 to 09:00, all authentication data is recorded as . After setting time, continue to set , , and with same manner. If some menu is not necessary, set as ’00:00-00:00. Each menu time shall not be overlapped.
VIRDI AC 1000 User Guide 3.5.2. Authentication method settings In the main menu, press [3] to select “3. Option” and the following screen appear: 1. Application 2. Verify Option 3. Set Door lock 4. Sound Control 5. Time Setting 6. Other Setting To set the default authentication method, press [2]. 3.5.2.1.
VIRDI AC 1000 User Guide 3.5.2.3. Settings for card only authentication ◆ [ENT] Æ [3] Æ [2] Æ [ENT] ◆ < Only Card > (N=0/Y=1):0 Default setting : ‘0’ Even for a user who is registered to be authenticated with a card & PW / card & fingerprint, he/she only needs to use a card if this option is set to ‘1’. This option is usually used when there are may terminals installed at the building entrance door where user entry/exit is frequent and the security level is relatively low.
VIRDI AC 1000 User Guide 3.5.3.2. Door status monitor ◆ [ENT] Æ [3] Æ [3] Æ [ENT] ◆ < Door Monitor > [0/1=NO/2=NC]:0 Default setting : ‘0’ - ‘0’: NW – no check - ‘1’: NO – dead bolt type or auto door (Lock monitoring is on when the door is locked) - ‘2’: NC - strike type (Lock monitoring is off when the door is locked) ‘0’ is for no check, ‘1’ is for dead bolt type or auto door; ‘2’ is for strike type.
VIRDI AC 1000 User Guide 3.5.4. Volume settings In the main menu, press [3] to select “3. Option” and the following screen appear: 1. Application 2. Verify Option 3. Set Door lock 4. Sound Control 5. Time Setting 6. Other Setting Press [4] for volume settings. 3.5.4.1. Voice settings ◆ [ENT] Æ [3] Æ [4] ◆ < Use Voice > (N=0/Y=1):1 Default setting : ‘1’ To make voice information available, set it to ‘1’. If not, set it to ‘0’. Press [ENT] to move to the next setting. 3.5.4.2.
VIRDI AC 1000 User Guide 3.5.5. Current time settings ◆ [ENT] Æ [3] Æ [5] ◆ In the main menu, press [3] to select “3. Option”. Press [5] to see the following screen: < Time Setting > 20060401211806 This is for the terminal current time. The above example represents the year 2006, month 04, date 01, hour 21, min. 18, and sec. 06. To change it, delete the old numbers with the [DEL] button before adding the new numbers. Press [ENT] to check that the current time is updated and move to the upper menu. 3.
VIRDI AC 1000 User Guide 3.5.6.2. LCD Brightness settings ◆ [Ent-] Æ [3] Æ [6] Æ [Ent] ◆ (0-2):1 Default : ‘1’ This is for LCD brightness level setting menu. The higher setting value is for high brightness. Press [ENT] to move to the next setting . 3.5.6.3. Display Time settings ◆ [Ent-] Æ [3] Æ [6] Æ [Ent] Æ [Ent] ◆ < Display Time > 0=20:30 1=PM 8:30 Default : ‘1’ This is for current time display mode setting menu.
VIRDI AC 1000 User Guide 3.6. Terminal information view ◆ [Ent-] Æ [4] ◆ In the main menu, press [4] to select “4.Terminal info” and the following screen appears where all the environmental settings are displayed: Terminal ID=0001 Ver=10.00.01 Application =Access Language=ENG Mode=SN Press [0] to scroll up and down the screen.
VIRDI AC 1000 User Guide 3.7. Extended functions In the main menu, press [5] to select “5.Ext functions” and the following screen appears: 1. Lock Terminal 2. Read Card No. 3.7.1. erminal lock settings ◆ [ENT] Æ [5] Æ [1] ◆ < Lock?> (N=0/Y=1):0 Default setting ‘0’: terminal lock clear ‘1’: terminal lock set Instead of a server program, an administrator can directly set up a terminal lock for a terminal.
VIRDI AC 1000 User Guide 3.8. Device settings In the main menu, press [6] to select “6. Device” and the following screen asking for the setting password appear: A device setting is an option that is not necessary to change after installation, so it is recommended not to change it except when it is really required. < Input PW > PW:_ _ _ _ _ _ _ _ This setting password is just for information, so it cannot be changed.
VIRDI AC 1000 User Guide 3.8.1.2. Language settings ◆ [ENT] Æ [6] Æ ‘084265’ + [ENT] Æ [5] Æ [ENT] ◆ < Language >:1 0=KOR 1=ENG 2=JPN 3=CHN 4=SPN 5=UAE 6=ITLY 7=VIET 8=OTH Default setting: ‘1’ (English) Voice information languages follow these settings: ‘0’: Korean, ‘1’: English, ‘2’: Japanese, ‘3’: Spanish, ‘4’: Chinese, ‘5’: Arabic, ‘6’:Italian, ‘7’:Vietnam ‘8’: Other language. ‘0’, ‘1’, ‘2’, ‘4’: LCD characters also correspond to the language.
VIRDI AC 1000 User Guide 3.8.3. Card reader settings ◆ [Ent-] Æ [6] Æ “084265” [Ent] Æ [3] ◆ :0 0=RF/SC 1=Wiegand Default setting: ‘0’ This is the setting for the card reader connected to a terminal. This shall be set to 0 except in the following cases:. - ‘0’: 125KHz card or 13.56MHz card - ‘1’: Additional card reader is connected through wiegand interface. (EX: HID reader) If it is set to the default setting ‘0’, it is possible to set to change card number display format.
VIRDI AC 1000 User Guide 3.8.4. Wiegand output settings ◆ [Ent-] Æ [6] Æ ‘084265’ [Ent] Æ [4] ◆ Wiegand Out:0 0=None 1=26bit 2=34bit Default setting: ‘0’ When this is set to [1], “Site code + user ID” is sent to the Wiegand port of the terminal when authentication is done. It can be used only for systems where there is a lock controller and the controller is operated by a Wiegand input. This is usually set to [0].
VIRDI AC 1000 User Guide 3.8.5.1. Settings initialization ◆ [ENT] Æ [6] Æ ‘084265’ + [ENT] Æ [6] Æ [1] ◆ < Init Config > [ Y=1 / N=2 ] : To initialize settings, press [1]. If not, press [2]. All the settings except Mac (physical) address are initialized, but the user and authentication records are not deleted. ※ if the settings are initialized, the language of the voice and menus becomes English. If you need to set other language (“6. Set Device”Æ “5.
VIRDI AC 1000 User Guide . 4. How to use the terminal 4.1. Access control - Menu “3.Option” Æ “1.Application” Æ [0] Access control settings 4.1.1.
VIRDI AC 1000 User Guide 4.1.2. Card authentication For a user who is registered as [RF], [RF|FP], or [RF|PW], when placing the card close to the default screen, a beep sound will be heard and the authentication result appears on the LCD. If you place your card close to the unit, you will hear a beep. 07/08/25 PM 4:58 07/08/25 PM 4:58 ▼ If authentication is successful, you will see a success message on the LCD together with the voice message “You are authorized”.
VIRDI AC 1000 User Guide 4.1.3. Password authentication If the user ID is “0001”, enter “0001” and press the function key. You will hear a beeping sound and the terminal waits for the user password to be input. Enter the password and press [ENT], and the authentication result appears on the LCD. If the user ID is ‘0001’, enter ‘0001’ and press the function key.
VIRDI AC 1000 User Guide 4.2. Time Attendance control - Menu “3.Option” Æ “1.Application” Æ [1] T&A (Time Attendance) settings - If the start/leave time is fixed, set , , and to reduce user input errors. 4.2.1.
VIRDI AC 1000 User Guide Working mode after authentication depends on , , and settings. The previous authentication mode is maintained if no mode is set for a specific time period. 4.2.4. Working mode expansion using multi-key authentication - If more than 5 working modes such as start, leave, outside work, return, and general are required, it can be expanded up to 41 modes. - After setting Menu Æ 3.Option Æ 1.
VIRDI AC 1000 User Guide 4.3. Meal control - Menu Æ “3. Option” Æ “1.Application” Æ [2] Meal settings - If the terminal is set for meal control, as the terminal is in “lock setting!’’ status during other time frames except for the meal times previously set, at least more than one time frame as meal time should be set for meal control usage. - Basically, a single authentication is allowed for each meal per user but double authentication is also possible “3. Option” Æ “1.
