Assembly Instructions Caution: You must read this before you proceed Please look in the support bar for hardware packs. Table Caution: This Table is NOT a TOY Keep your child/children at bay during the assembly process. Whenever moving/lifting the Table and to prevent damage to the Table, two adults are needed to execute these actions.
Parts List Label Picture Description QTY A Side Table Top 2 B Center Table Top 1 C End Table Top 2 D Table Top Support Bar 4 E First Leg 2 F Second Leg 2 First Leg Support Bar Second Leg Support Bar G H 2 1 Hardware Label ① ② ③ ④ ⑤ ⑥ Picture Description Bolt (M8x40mm) Bolt (M8x25mm) Screw (M6x45mm) Screw (M6x50mm) Washer (M8.
Assembly Preparation Before Beginning Assembly: x 17 x 17 x5 x 33 x 29 Page 3 of 10
Assembly Steps Overview Side Table Top (A) Center Table Top (B) End Table Top (C) Second Leg (F) First Leg (E) Second Leg Support Bar (H) First Leg Support Bar (G) FRONT FACING This Table has multiple parts and may require up to 45 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 2 A B Place Side Table Tops(A) and Center Table Top(B) facedown onto a clean, non-marring surface. Then align them as pictured. Step 3 C 6 A 4 A C Place the End Table Tops(C) as pictured above. Attach End Table Top(C) to Side Table Tops(A) using Screws(④) with Allen Key(⑥) as pictured above. Do not fully tighten the Screws.
Step 4 C 6 A 3 5 A C Attach End Table Top(C) to Side Table Tops(A) using Screws(③), and Washers(⑤) with Allen Key(⑥) as pictured above. Do not fully tighten the Screws. Step 5 C 6 A 1 A C B Attach End Table Tops(C) to Side Table Tops(A) and Center Table Top(B) using Bolts(①) with Allen Key(⑥) as pictured above.
Step 6 6 D A 4 A B Attach Table Support Bars(D) to Side Table Tops(A) and Center Table Top(B) using Screws(④) with Allen Key(⑥) as pictured above. Do not fully tighten Screws. Step 7 C 6 E 2 5 Attach First Leg(E) to End Table Top(C) using Bolts(②), and Washers(⑤) with Allen Key(⑥) as shown in the picture above. Repeat the same process with the remaining First Leg(E) and Second Legs(F). Do not fully tighten the Bolts.
Step 8 G F E E F 1 6 5 Attach the First Leg Support Bar(G) to First Leg(E) and Second Leg(F) using Bolts(①), and Washers(⑤) with Allen Key(⑥) as shown above. Repeat the same process with the remaining First Leg Support Bar(G). Do not fully tighten the Bolts. Step 9 G H 6 2 5 Attach Second Leg Support Bar(H) to First Leg Support Bar(G) using Bolts(②), and Washers(⑤) with Allen Key(⑥) as pictured above. Do not fully tighten the Bolts.
Step 10 Stand the Table up, with assistance from your adult partner. Exert pressure floorwards, onto the Table with both your hands. This pressure will help the Legs and Table Top reach full alignment status. Check for wobbles on a LEVEL surface. If no wobbles are found proceed to tighten the Bolts and Screws in a sequential manner, until evenly secured. When tightening the Bolts and Screws tighten sequentially. Do not tighten any Bolt or Screw fully and then move on towards the next one.
Page 10 of 10
