User's Manual
Table Of Contents
- 1.0 INTRODUCTION
- 2.0 FEATURES & OPTIONS
- 3.0 SAFETY WARNINGS
- 4.0 WARRANTY (summary)
- 5.0 UNPACKING AND INSPECTION
- 6.0 GENERAL SPECIFICATIONS
- 7.0 PRINCIPAL OF OPERATION
- 8.0 FRONT PANEL DESCRIPTION
- 9.0 REAR PANEL DESCRIPTION
- 10.0 LED Indicators
- 11.0 MAKING CONNECTIONS TO THE X75
- 12.0 INSTALLATION
- 13.0 USING THE CONTROLLER WEB BROWSER INTERFACE
- Appendix 1 – SNMP MIB Information
- Appendix 2 – Load LVD Configuration (model X75-12-A-GHHIL-S-578 only)
- Appendix 3 – Revision History
- Figure 1 - X75 Compact Integrated DC Power System
- Figure 2 - Block Schematic
- Figure 3a - Front View with Breakers (configuration A)
- Figure 3b - Front View with GMT Fuses (configuration B)
- Figure 4 - Rear Views of Base and Expansion Units
- Figure 5 - LED Indicators
- Figure 6 - Recommended Load Circuit Wire Sizes
- Figure 7 - Battery Temp. Probe & Alarm Relay Connector Pin-Out
- Figure 8 - Ethernet Connector Pin-Out
- Figure 9 - Auxiliary Connector Pin-Out
- Figure 10 - Input Current Ratings
- Figure 11 - Controller Status WEB Page (typical)
- Figure 12 - Rectifier Status WEB Page (typical)
- Figure 13 - Rectifier I²C Addressing
- Figure 14 - Controller Factory Calibration WEB Page (typical)
- Figure 15 - Controller Site Installation WEB Page (typical)
- Figure 16 - Alarm Configuration WEB Page (typical)
- Figure 17 - Controller Network Settings (typical)
- Figure 18 - Controller Alarm Log WEB Page (typical)
- Figure 19 - Controller Control Panel WEB Page (typical)
- Figure 20 - Controller System Settings WEB Page (typical)
- Figure 21 - SNMP Configuration WEB Page (typical)
- Figure 22 - Controller Help WEB Page (typical)
- Figure 23 - About UNIPOWER Telecom WEB Page (typical)
Page 17
X75 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x75-10b
x75-man-Rev10b-0514.indd
11.2 AlarmRelayandBatteryTemperatureProbeConnections–J4
Connection to the Form-C alarm relay outputs is made through a 15-way spring
clamp terminal connector. There are a total of 4 relay outputs with Normally Open,
Normally Closed and Common Contacts available for connection. The individual
relays contact sets are fully isolated and may be oated from GROUND by up to 100V.
Maximum contact current and voltage are 1A and 30V (DC or AC) respectively.
This connector accommodates wire sizes in the range #28 to #20AWG.
The alarm relays are designated K1 to K4. K1 and K2 are pre-programmed for
MAJOR and MINOR alarm conditions by default. K3 and K4 are not programmed
for any alarm function.
The function of each alarm may be programmed using the Alarm Conguration
WEB page described later in section 13.
Connection of the supplied battery temperature probe, if required, is made using
terminals 1 and 3 of this same spring clamp terminal connector.
J4 CONNECTIONS
TERMINAL FUNCTION
1 BATT. TEMP. PROBE -
2 Not Used
3 BATT. TEMP. PROBE +
4 K1 - MAJ ALARM – N/C
5 K1 - MAJ ALARM – COM
6 K1 - MAJ ALARM – N/O
7 K2 - MIN ALARM – N/C
8 K2 - MIN ALARM – COM
9 K2 - MIN ALARM – N/O
10 K3 – FREE ALARM – N/C
11 K3 – FREE ALARM – COM
12 K3 – FREE ALARM – N/O
13 K4 – FREE ALARM – N/C
14 K4 – FREE ALARM – COM
15 K4 – FREE ALARM – N/O
Note that terminal 1 is to the left when viewed from the rear of the system.
Figure7-BatteryTemp.Probe&AlarmRelayConnectorPin-Out