Ad va n ce d S c re e n Sys te m s Surface Mount Ad va n ce d S c re e n Sys te m s Premium Security Screen Door Installation Instructions Ad va n ce d S c re e n Sys te m s Ad va n ce d S c re e n Sys te m s • • • • • Read completely through the installation instructions before proceeding with installation Ad va n ce d S c re e n Sys te m s Installation requires two people Use appropriate protective equipment, including safety glasses Children should not be allowed in work area Failure to install do
DOOR PARTS HARDWARE & FASTENERS A) Top header jamb A1) Top header jamb snap cover B) Hinge-side jamb B1) Hinge-side snap cover C) Security screen door D) Lock-side jamb D1) Lock-side snap cover E) Bottom bar F) Bug sweep G) Threshold plate H) Hinges (3) & fasteners (18) I) Latch guard J) #10x2-1/2" flat-head screws (12 pcs.
1 Determining Identify and prepare Your Build mounting Out Area surface (continued) Inspect Your Entryway for Obstructions Check for any obstructions above and around your entryway that may prevent the outward swing of your new security door, and/or its installation, such as: Light fixtures Low overhang Door bell Trees, bushes, or hanging plants Determine Type and Readiness of Mounting Surface Your security door will require a minimum mounting surface of 1" on the trim above, and on both sides
2 Determining Determine your Your threshold Build Out configuration Area (continued) Look at your existing entry door threshold and use the diagrams below to determine which threshold configuration best applies to your entryway. This will determine whether a bottom bar is or is not required for your security door. Bottom Bar Required 3 Bottom Bar NOT Required The concrete is set back and lacks space to mount to the threshold plate. The concrete extends at least 7/8" further than your trim.
4 Determining Install the bottom Your Build bar if Out applicable Area (continued) If there is NOT a 2-3/4" space below both jambs it is necessary to install the bottom bar assembly. It is okay to move the jambs up within the doorway to ensure this space, as long as the top of the jambs do not go beyond the top-edge of your mounting surface. The bottom bar (E) will need to be installed 1/8" to 1/4" lower than the existing doorway so that there is a slope to the threshold.
1 7 Determining Install handleYour and Build lockset Out Area (continued) 1) Start on the interior side of the door. With the handle (O) facing toward the screen, insert the spindle and mounting screws through the mortise gear in the door panel. 2) On the exterior of the door with the handle pointing toward the screen, align the openings on the inside of the handle with the spindle and mounting screws. Position the handle against door frame.
11 1 Install Determining latch guard Your Build Out Area (continued) 1. Remove top and bottom screws from the one-piece gear. 2. Attach the latch guard provided in the hardware box using two #8x1" painted flat-head screws (M) in the pre-drilled holes. 12 1 Adjust Determining and align Yourdoor Build& Out install Area permanent (continued)screws CAUTION: The door must be close enough to the lockside jamb (D) to engage the 3-point locking system trigger. If not, the hardware will not operate properly.
14 1 Install Determining threshold Yourplate Build Out Area (continued) 2 1 Existing door contour 3 Make cardboard template 4 Fit template to contour 5 Cut template to contour Mark threshold plate 6 Cut threshold plate to fit 1 The contour of door framing varies, making it necessary to cut the threshold plate (G) to fit. We recommend cutting a cardboard template (Q) to fit the opening first, to avoid cutting the threshold plate incorrectly.
Final touch-up suggestions 1 Caulk (not included) Caulk around the outside of the security door jamb frame, using paintable caulk, and paint to the desired color. 2 White Grease Lubricant (not included) Use white grease to lubricate the hinges of your new security door. Care and maintenance Over time, airborne dust, dirt, and impurities can accumulate, which will cause visual defects to your Meshtec screen and, if not regularly and properly removed, can lead to further damage, staining, and corrosion.
Ad va n ce d S c re e n Sys te m s Ad va n ce d S c re e n Sys te m s Instalación sobre superficie Instrucciones de instalación de puerta con malla de seguridad premium Ad va n ce d S c re e n Sys te m s Ad va n ce d S c re e n Sys te m s • • • • • Lee todas las instrucciones de instalación del kit antes de la instalación Ad va n ce d S c re e n Sys te m s La instalación requiere de dos personas Usa el equipo de protección apropiado, incluyendo gafas de seguridad Mantén los niños alejados del área de
PIEZAS DE LA PUERTA HERRAJES Y SUJETADORES: A) Jamba del travesaño superior A1) Cubierta a presión de la jamba del travesaño superior B) Jamba del lado de las bisagras B1) Cubiertas a presión del lado de las bisagras C) Puerta con malla de seguridad D) Jamba del lado de la cerradura D1) Cubierta a presión del lado de la cerradura E) Barra inferior F) Guardapolvo inferior contra insectos G) Umbral H) Bisagras (3) y sujetadores (18) I) Protector del pestillo J) Tornillos de cabeza plana núm.
1 Determining Determina y prepara Your Build la superficie Out Area (continued) de montaje Revisa si hay obstáculos en la entrada Comprueba si arriba o alrededor de la entrada hay obstáculos que puedan impedir la instalación de la nueva puerta de seguridad o su abertura hacia afuera; obstáculos como: Lámparas Salientes bajos Timbre de puerta Árboles, arbustos o plantas colgantes Determina el tipo y el estado de la superficie de montaje Tu puerta de seguridad necesita una superficie de montaje de
2 Determining Determina la Your configuración Build Out de Area tu (continued) umbral Observa el umbral de tu puerta de entrada actual y usa los diagramas más abajo para determinar cuál es el umbral adecuado para tu entrada. Esto determinará si necesitarás o no instalar una barra inferior en tu puerta de seguridad. Requiere la barra inferior No hay espacio en la superficie de concreto para montar la placa del umbral.
4 Determining Instala la barra Your inferior BuildsiOut es Area necesario (continued) Si NO cuentas con un espacio de 7 cm debajo de ambas jambas, debes instalar el ensamblaje de la barra inferior. Se pueden mover las jambas hacia arriba dentro de la entrada para dejar este espacio, siempre que la parte superior de las jambas no pase del borde superior de la superficie de montaje. CASA La barra inferior (E) debe instalarse de 3.2 a 6.
1 7 Determining Instala la manija YouryBuild la cerradura Out Area (continued) 1) Comienza desde la parte interior de la puerta. Con la manija (O) de frente a la malla, inserta el eje y los tornillos de montaje a través del mecanismo de mortaja en el panel de la puerta. 2) En el exterior de la puerta con la manija hacia la malla, alinea las aberturas de la parte interior de la manija con el eje y los tornillos de montaje. Ubica la manija contra el marco de la puerta.
10 1 Instala Determining la jamba Yourdel Build travesaño Out Area superior (continued) A Coloca la jamba del travesaño superior (A) en su lugar, alíneala para que quede al ras en ambos extremos con cada jamba lateral. Coloca un tornillo para drywall núm. 6 de 2" (K) incluido en el orificio del lado de la cerradura (lado derecho en este diagrama de ejemplo) y monta provisionalmente la jamba del travesaño superior. C B D Estos tornillos se usan para mantener temporalmente la jamba a plomo.
13 1 Determining Verifica el mecanismo Your Buildde Out cierre Area (continued) Verifica que el mecanismo de cierre abre, cierra y queda bien seguro. Para probarlo, hala hacia abajo la manija y abre la puerta. Hala hacia arriba la manija para enganchar el mecanismo de cierre de 3 puntos y enseguida gira el cerrojo tipo mariposa en el interior de la puerta hacia la derecha, o gira la llave hacia la izquierda para cerrar.
16 1 Instala Determining el tapón Your delBuild pestillo Out Area (continued) Instala el tapón del pestillo (N) en la ranura inferior sin usar. 17 1 Instala Determining las cubiertas Your Build a presión Out Area (continued) Coloca la cubierta a presión (A1) en la primera jamba del lado de las bisagras (Fig. 1, paso 1). Con un mazo de goma, golpea en el lado de la cubierta a presión como se muestra en la (Fig. 2) para colocar adecuadamente la cubierta a presión en su sitio.
Sugerencias de retoques finales 1 Pasta selladora (no se incluye) Aplica pasta selladora para pintar en el exterior del marco de la jamba de la puerta de seguridad y pinta del color deseado. 2 Lubricante de grasa blanca (no se incluye) Cada seis meses, lubrica con grasa blanca las bisagras de la puerta de seguridad nueva.