Portable Data Collection Terminal User Guide
Notice This unit is equipped with a battery pack and backup battery. It is possible that the Unitech PA500 may not power-on due to battery discharge as a result of storage. In the above situation, plug the PA500 to the USB charging cable which is with DC in port or put the unit into the cradle or docking station (with 5V/3A AC-DC adapter), and recharge the unit for 16 hours in order to fully charge its backup battery.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
INFORMATION TO USER To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IMPORTANT NOTE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operation instruction for satisfying RF exposure compliance.
1 PA500 & Accessories PA500 Features Powerful System Display Barcode Scanner Audio Wireless Connectivity Battery Life User-friendly Interface PA500 Tour Front View Rear View Left and Right View Top and Bottom View First Steps with PA500 2 3 3 3 3 3 3 3 3 4 4 6 7 8 9 Chapter 2 Hardware and Command Interface 15 Using the Stylus Using the SDIO/MMC Slot Using the Laser Scanner Using the Software Keyboard Button Command Interface Today Screen Status Icons Navigation Bar Command Bar Pop-up Menus Notification
Chapter 4 Managing Programs 55 Accessing Programs Opening a Program Switching Between Programs Accessory Programs Scan2Key Scanner Settings 55 55 55 56 56 57 Chapter 5 Customizing PA500 61 Adjusting Settings Checking Main and Backup Battery Status How to Save Battery Life Changing the Automatic Power Settings Adjusting Backlight Setting Resetting the Device Warm Boot Clean Boot Cold Boot Viewing Flash ROM Files Adding Programs Adding Programs to Your Device Adding a Program to the Start Menu Removing
1 Chapter 1 Introduction Thank you for purchasing PA500. Your PA500 is a rugged, compact and lightweight palm-size computer. It utilizes the Windows Mobile 5.0 operating system, and incorporates an integral barcode scanning laser device, color LCD with touch screen, keypad, IrDA interface, Bluetooth, and wireless communication capability. It provides the user with a standard Windows-based environment for customizing and operating the device.
2 Chapter 1 Introduction PA500 & Accessories After opening the box, please make sure the following accessories for the PA500 are present: PA500 Main Body Unitech PA500 Quick Reference Guide Battery pack PA500 CD USB charging cable Stylus Earphone AC adapter* * The adapter’s replaceable plug clips availability depends on region.
3 PA500 Features Powerful System • Microsoft Windows Mobile 5.0 operating system • Intel PXA270 processor with speed of up to 520 MHz • System memory: • 64 MB SDRAM • 64 MB Flash ROM Display • 3.5” QVGA LCD touch-sensitive screen • 320 x 240 resolution Barcode Scanner • Symbol SE950 • Integrated Hitachi HD6433657W barcode decoder Audio • Supports Windows Media Player • Voice recording and playback Wireless Connectivity • 802.
4 Chapter 1 Introduction PA500 Tour The following section gives you a tour of the PA500 hardware interface. Front View No. Component Description 1 Power button If the device is off, press this button to turn it on. Alternatively, when the unit is on, this key must be pressed and held down for about two seconds in order to turn the device off. 2 LCD Touch screen Displays the applications and data stored on your device. It is touch-sensitive and responds to the stylus or finger.
5 No. Component Description 5 Today button Customize the look and information that is displayed on the Today screen. 6 Calendar button Press to bring up Calendar. Calendar enables you to conveniently manage your schedules and appointments or any other activities associated with a date and time. 7 Tasks button Keep track of what you have to do and prioritize them based on their importance and urgency. 8 Software keyboard button Press to launch the Windows CE keyboard.
6 Chapter 1 Introduction Rear View No. Component Description 1 Speaker Listen to audio media. When speaker phone is active, sounds are emitted here. 2 Strap holder Eyelet for holding strap. 3 Reset button Press the end of the stylus into the button to reset your device. 4 Main battery Removable and rechargeable 3.7 V, 2200 mAh battery pack. 5 Battery release latch Slide toward the right side of the device and hold firmly, then detach the battery from its bay.
7 Left and Right View No. Component Description 1 Infrared (IR) port Uses infrared technology to transmit and receive data from other IR-enabled devices. 2 Right side scanner trigger button Press to activate the barcode laser scanner. 3 Earphone jack Lift the rubber cover from the earphone jack and connect an audio line-out device (earphone or headphone). 4 Left side scanner trigger button Press to activate the barcode laser scanner.
8 Chapter 1 Introduction Top and Bottom View No. Component Description 1 Barcode laser scanner (optional) Reads and captures information on a barcode label. 2 SDIO/MMC slot Accepts an SD (Secure Digital), MMC (Multimedia Card) or SDIO (Secure Digital Input Output) cards, allowing you to add more memory. Install add-on applications or use audio text files stored in it for use with internal applications. You can also use it to back up data from your device.
9 First Steps with PA500 Perform the following easy installation steps to start using your device: 1 Install the battery pack WARNING! There is a risk of fire and burns if the battery pack is handled improperly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water. DO NOT attempt to open or service the battery pack. Dispose of used batteries according to local recycling guidelines in your area.
10 Chapter 1 Introduction CAUTION: Operating the PA500 for the first time without the AC adapter, and without fully charging the backup battery may result in loss of data stored in RAM memory. NOTE: Data you enter may not be properly stored until the built-in backup battery has been adequately charged. To charge the device using the USB charging cable: (1) Press and hold the connector button on the USB charging cable and connect it to the PA500.
11 To charge the device using the docking station: (1) Plug the AC adapter cable into the power jack on the docking station. (2) Connect the AC adapter into an electrical outlet. (3) Slide the device into the docking station until it clicks into place. The connection is secure when the bottom edge of the device is aligned smoothly with the docking station, and the LED indicator on the device lights up red.
12 Chapter 1 Introduction LED status during charging: • Solid red: Charging • Solid green: Charging complete If the battery level becomes low in the course of normal use, a status icon appears on the device screen indicating low or very low battery status. In both cases, perform an ActiveSync operation to back up your data, then recharge your device as soon as possible.
13 The Unitech PA500 welcome screen appears. The Windows Mobile screen will appear shortly thereafter. (2) Calibrate the PA500 The calibrate screen will automatically appear when the unit is powered-on for the first time or after the system is reset. This screen can also be accessed at any time by tapping Start > Settings > System tab > Screen. The PA500 will prompt you to calibrate the unit by tapping a sequence of screen locations. Tap gently but firmly.
14 Chapter 1 Introduction
15 Chapter 2 Hardware and Command Interface This chapter describes basic hardware procedures in using your PA500. Information on the device’s command interface is also discussed. Using the Stylus CAUTION: Never use anything other than the PA500 stylus on the screen. Using another object as a stylus could cause permanent damage. 1 Remove the stylus from its holder. 2 Hold the stylus as you would a pencil. 3 To make a choice from a menu, lightly tap the tip of the stylus on that choice.
16 Chapter 2 Hardware and Command Interface Using the SDIO/MMC Slot Your device has an expansion slot compatible with a range of SD, SDIO, and MMC storage cards, which are primarily used to back up or transfer files and data. To insert a storage card: 1 Hold the device securely, then lift the rubber cover from the SDIO/ MMC slot. 2 Push the card into the slot until you hear an audible system sound; this will signal that the card is already properly seated within the slot.
17 Using the Laser Scanner PA500 has an integrated laser scanner which reads all major barcode labels with excellent performance. NOTE: The reading software must be enabled in order to operate the scanner. This can be a user-loaded application or a pre-loaded utility such as Scanner Settings. PA500 has a built-in Scanner Settings utility that allows you to test the device’s barcode scan function. To launch Scanner Settings: 1 Tap Start > Settings > System tab.
18 Chapter 2 Hardware and Command Interface 4 Tap Test tab. 5 Activate the laser scanner by pressing either one of the trigger keys located on the left and right side of the unit. 6 Aim the laser scanner at the selected barcode and press both trigger keys to scan. The scanned barcode data appears on the screen. 7 Tap OK.
19 Using the Software Keyboard Button The Windows CE software provides a touch screen keyboard for input of other characters. The Windows based keyboard replicates the layout of a standard PC keyboard. To open the Windows CE keyboard: Do either of the following: • Press the Software keyboard button on the device’s front panel. • Tap the keyboard icon on the command bar. The Windows CE keyboard pops up.
20 Chapter 2 Hardware and Command Interface Command Interface Today Screen When you turn on your device for the first time each day or after a preset period of inactivity, you’ll see the Today screen. You can also display it by doing either of the following: • Tap Start > Today. • Press the Today button on the device’s front panel.
21 To define a preset period of inactivity after which the Today screen is displayed: 1 Tap Start > Settings. 2 On the Personal tab, tap Today.
22 Chapter 2 Hardware and Command Interface 3 On the Items tab, select the Today timeout check box. 4 Tap the pick list beside the check box to set the period of inactivity. 5 Tap OK. Today screen provides an at-a-glance view of the important reminders and details for the day.
23 Status Icons The table below describes some of the status icons you may see on your device. Status icon Description Turns all sounds on and off. Indicates Bluetooth wireless technology is on. Indicates that the main battery is charging. The PA500 is either plugged-in via the AC adapter or docking station. Indicates the main battery is fully charged. Indicates the main battery is low and needs to be charged. Indicates the main battery is very low. Stop device operation and charge the device immediately.
24 Chapter 2 Hardware and Command Interface Navigation Bar The navigation bar is located at the top of the screen. It displays the active program and current time, and allows you to switch to other programs and close screens. Command Bar Use the command bar at the bottom of the screen to perform tasks in programs. The command bar includes menu names, buttons, and the Input Panel button. • To create a new item in the current program, tap New.
25 Pop-up Menus With pop-up menus, you can quickly choose an action for an item. The actions in the pop-up menus vary from program to program. To access a pop-up menu: 1 Tap and hold the stylus on the item that you want to perform the action on. 2 When the menu appears, lift the stylus, then do any of the following: • Tap the action you want to perform.
26 Chapter 2 Hardware and Command Interface Notifications Your device reminds you in a variety of ways when you have something to do or receive a message. For example, if you’ve set up an appointment in Calendar, a task with a due date in Tasks, or an alarm in Clock, you’ll be notified in any of the following ways: • A message box appears on the screen. • A sound, which you can specify, is played. To choose reminder types and sounds for your device: (1) Tap Start > Settings.
27 (3) On the Notifications tab, select the kind of events you want to be notified of and the manner of notification you prefer. The options you choose here are applied globally in your device. (4) Tap OK.
28 Chapter 2 Hardware and Command Interface
29 Chapter 3 Getting Connected This chapter describes the procedures on how to connect the device to your computer. Establishing Device-PC Connection Installing Microsoft ActiveSync In order to exchange data between your computer and PA500, Microsoft ActiveSync must be installed on your computer. The USB charging cable that comes with your device enables you to connect the device to your computer.
30 Chapter 3 Getting Connected After you have installed ActiveSync and restarted your computer, the ActiveSync icon will appear on your computer’s system tray (on the lower right-hand corner of the screen) and the ActiveSync wizard appears. For detailed information on how to use ActiveSync on your computer, start ActiveSync; then click Help > Microsoft ActiveSync Help. Connecting the Device to Your Computer 1 After ActiveSync has been installed, connect the USB charging cable to your device.
31 NOTE: If ActiveSync doesn’t start automatically, click Start > Programs > Microsoft ActiveSync > File > Connection Settings > Connect > OK. If a message appears indicating that it is unable to detect a connection, click the Cancel button and manually configure the communication settings. 5 Follow the onscreen instructions. 6 When the configuration process is complete, the ActiveSync window appears.
32 Chapter 3 Getting Connected Synchronizing with Your Computer Synchronization takes place according to the options you choose while setting up ActiveSync on your computer. If you accept the default (On Connect) synchronization option in the Microsoft ActiveSync Setup Wizard, you’ll be able to simply connect your PA500 to your desktop computer and sychronization will take place.
33 USB Connection To synchronize with your computer using USB connection: 1 Open ActiveSync on your computer. 2 Connect your device to your computer using the USB charging cable. See “Connecting the Device to Your Computer” on page 30. 3 Initiate connection by tapping Start > Programs > ActiveSync. 4 Tap Menu, then Connections. 5 Select Synchronize all PCs using this connection check box. 6 Select a baud rate or cable type connection. 7 Tap OK.
34 Chapter 3 Getting Connected Infrared Connection The infrared (IR) port allows you to synchronize information with an infrared-enabled computer. Simply align the infrared port of your device with that on the computer. This method is ideal for quickly switching between multiple devices since there are no cables or adapters to change. 1 Perform the steps below on your computer. (1) Configure an infrared port on your computer following the manufacturer’s instructions.
35 Bluetooth Connection Your device is equipped with Bluetooth wireless technology that you can use to synchronize information with a computer equipped with a Bluetooth adapter or access point. Bluetooth wireless technology allows you to communicate with the computer whenever it is within range. 1 Perform the steps below on your computer. (1) On the Windows taskbar, click Start > Settings > Control Panel > Bluetooth Devices.
36 Chapter 3 Getting Connected (b) Tap Bluetooth. (c) Tap Done. Using the Bluetooth program (a) Tap Start > Settings. (b) On the Connections tab, tap Bluetooth.
37 (c) On the Mode tab, select all the check boxes. (d) Tap Devices tab and create a Bluetooth partnership. Refer to page 47 for more information. (2) Make sure that the device and computer are within close range. (3) Initiate connection by tapping Start > ActiveSync > Menu > Connect via Bluetooth. (4) Tap Sync.
38 Chapter 3 Getting Connected WiFi Connection With the device’s embedded WLAN module, you can send and receive signals to a computer connected on the WiFi network then synchronize files. NOTE: Before doing these steps, you must do the following: - Make sure your computer have TCP/IP installed. - Make sure the network system and remote access server in your workplace supports TCP/IP. - Make sure you have remote access account.
39 2 Perform the steps below on your device. (1) Enable WiFi access on your device. Using Today screen (a) On the Today screen, tap WiFi. (b) Tap Wi-Fi to enable. (c) Tap Done.
40 Chapter 3 Getting Connected Using the Wireless Manager (a) Tap Start > Settings. (b) On the Connections tab, tap Wireless Manager. (c) Tap Wi-Fi to enable. (d) Tap Done.
41 (2) If there are networks already detected, tap and hold network name, then select Connect. If none, tap Add New and follow all onscreen instructions. (3) Under the Network to access drop-down menu, select Only computer-to-computer. (4) When finished, tap OK. For more information on how to configure the wireless network settings, tap Start > Help .
42 Chapter 3 Getting Connected Synchronizing Information By default, ActiveSync does not enable automatic synchronization of all types of information. To select the types of information you want synchronized, on either your device or your computer, go to Menu, then Options. This section gives you an overview of the types of Outlook information you can synchronize.
43 Synchronizing Contacts • Contacts created on your device are copied to your computer or on a Microsoft Exchange server during synchronization, and vice versa. By default, all of your contacts will be synchronized. • Similarly, contacts that are deleted from your device are deleted from your computer and/or server during synchronization, and vice versa. Synchronizing Tasks • Task synchronization is, by default, automatically selected in ActiveSync.
44 Chapter 3 Getting Connected Using ActiveSync to Exchange Files You can use ActiveSync to exchange information from your device your computer and vice versa. Changes you make to the information on one location will not affect the information on the other one. If you want to automatically update information on both your device and computer, synchronize the information instead. You can copy two types of information to your device: files and Pocket Access Windows CE Store information.
45 Sharing Information You can use your PA500 to exchange information with other mobile devices and connect to your computer, a network, or the Internet. You have the following options: • Infrared connection • Bluetooth connection • WiFi connection • VPN connection • Email server connection Infrared connection Using the infrared (IR) port on your device to beam information, such as contacts and appointments, from another IR-enabled device.
46 Chapter 3 Getting Connected 2 Align the IR port of your device with that of the IR-enabled device so that they are unobstructed and within a close range. 3 Do any one of the following: 4 • Tap and hold the item, then tap Beam Task on the pop-up menu. • Using File Explorer, tap and hold the item (but not folder), then select Beam File on the pop-up menu. • Using Pictures & Videos, tap and hold a thumbnail to display a pop-up menu of available actions, then tap Beam.
47 Bluetooth connection Your device allows you to connect to a Bluetooth-enabled device, such as a handheld, headset, or computer. Once connected you can do the following: • Beam files and information in Calendar, Contacts, Notes, Tasks, Excel Mobile, Word Mobile, PowerPoint Mobile, and Pictures & Videos programs, to other Bluetooth-enabled device. • Wirelessly listen to audio files or locate and use services on a Bluetooth-enabled device. • Locate and use any services available on the device.
48 Chapter 3 Getting Connected Your device will search for other devices with Bluetooth capabilities and displays them in the device list. (4) Tap the name of the device in the list, then tap Next. (5) If you want to use a passkey, enter the alphanumeric passkey, then tap Next. Or, you can leave the passkey blank, then tap Next. The passkey is recommended for enhanced security. Your passkey must be between 1 to 16 alphanumeric characters. (6) In the Display Name box, enter a new name for the device.
49 (7) In the “Select services to use from this device” list, select a service. (8) Tap Finish. Sending and receiving information via Bluetooth To send information via Bluetooth: 1 Switch to the program where you created the item you want to send and locate the item in the list. 2 Do any one of the following: 3 • Tap and hold the item, and then tap Beam Task on the pop-up menu. • Using Pictures & Videos, tap and hold a thumbnail to display a pop-up menu of available actions, then tap Beam.
50 Chapter 3 Getting Connected WiFi connection Windows Mobile can support TCP/IP protocol, so the user can easily connect to the Internet by modem or high-frequency wireless LAN technology. WiFi networks look and operate similarly to Ethernet networks. The only difference is that a radio transmission replaces the hard-wire connection between the various nodes.
51 If there are networks already detected, tap and hold network name, then select Connect. If none, tap Add New and follow all onscreen instructions. 5 6 Under the Network to access drop-down menu, select from the following network connection options: • All available • Only access points • Only computer-to-computer When finished, tap OK. To configure the wireless network connection settings, tap Start> Settings > Connections tab > Network Cards.
52 Chapter 3 Getting Connected • Password • Domain name • TCP/IP settings • Host name or IP address of the VPN server 2 Tap Start > Settings. 3 On the Connections tab, tap Connections. 4 On the Tasks tab, tap Add a new VPN server connection. 5 Follow all onscreen instruction in the New Connection wizard. For more information, tap Start > Help.
53 Connecting to the Internet Your PA500 allows you to connect to your ISP (Internet Service Provider) and use the connection to do the following: • Send and receive email messages • View the Internet and Intranet • Access Web pages • Listen to streaming media To connect to the Internet: 1 Ask your ISP for the following information: • Dial-up access telephone number or access point • User name and password 2 Tap Start > Settings.
54 Chapter 3 Getting Connected
55 Chapter 4 Managing Programs This chapter describes the procedures for launching programs. It also shows how to use the Scan2Key and Scanner Setting accessory programs. Accessing Programs Opening a Program You can open programs in any one of the following ways: • Tap a program name from the Start menu. • You can select which programs are displayed on the Start menu. For instructions, see Adding a program to the Start menu on page 71. • Tap Start, then Programs to see more programs.
56 Chapter 4 Managing Programs Accessory Programs Scan2Key The Scan2Key application can route input from a scanner port to keypad buffer, so that all input from scanner will be treated as they are just input from touch screen keyboard. With this router, scanned data can be directly input into scanner port aware application, like MS Pocket Word. To launch Scan2Key: 1 Tap Start > Programs. 2 Tap Scan2Key. Scan2Key will appear on lower right corner of the Today screen.
57 To exit Scan2Key: 1 Tap and hold the Scan2Key icon then tap Exit on the pop-up menu. The Quit Scan2Key dialog box appears. 2 Tap Yes. Scanner Settings When it is necessary for the user to change the default barcode symbology for a different application, the Scanner Control Panel provides the ability to change default symbology. The Scanner Control Panel also lets you place delimiter characters behind scanned data and save the settings.
58 3 Chapter 4 Managing Programs On the Settings tab, tap the plus sign in front of Barcode Symbologies to expand and display the list of barcode symbologies. Below table lists the standard protocol for a particular type of barcode symbology.
59 Check Char/ Digit Verification Transmit check char/digit Transmit start & stop bits Barcode Symbology Enable/ Disable EAN 128 Yes EAN 13 Yes Yes Transmit leading char/ digit EAN 8 Yes Yes Transmit leading digit Interleaved 2 of 5 Yes Yes Not Suppress start or stop digit Fixed length 10 to 64, data length Label Code IV & V Yes Yes MSI/Plessy Yes Yes Check digital double module 10 1 to 16, data length Standard 2 of 5/Toshiba (China Postal Code) Group Yes Yes Fixed length 4 to
60 Chapter 4 Managing Programs
61 Chapter 5 Customizing PA500 This chapter describes the procedures on how to adjust the settings of your device. Adjusting Settings You can adjust the settings of your device to suit the way you work. Adjusting certain settings, such as backlight, auto power off timer, system volume, and processor speed. To access Settings, tap Start > Settings.
62 Chapter 5 Customizing PA500 Checking Main and Backup Battery Status View power level for both the main and backup battery. To minimize power consumption, you can define settings for the auto-off function and the processor’s operation speed. To check the main and backup battery status: 1 Tap Start > Settings. 2 On the System tab, tap Power. 3 Do either of the following: 4 • If the Plug or Battery icon appears on your device, doubletap the icon to bring the Power settings screen.
63 How to Save Battery Life You can save your device’s battery life by doing either of the following: • Change the automatic power settings • Minimize use of backlight Changing the Automatic Power Settings The PA500 will enter idle mode when there is no task, or all tasks are waiting for input. In default setting, the PA500 will automatically turn itself off if it remains idle for 3 minutes and when there is no external charging power applied.
64 3 Chapter 5 Customizing PA500 Tap the Advanced tab, then tap the “On battery power turn off device if not used for” check box and change the amount of time before the unit turns off the backlight while running in battery power mode. This function can also be activated when the PA500 is plugged into the power adapter or placed in its docking station.
65 2 On the System tab, tap Backlight. 3 On the Battery Power tab, do either of the following: 4 • Tap the “Turn off the backlight if device is not used for” check box and change the amount of time before the unit turns off the backlight while running in battery power mode. • Tap “Turn on backlight when button is pressed or the screen is tapped” check box.
66 Chapter 5 Customizing PA500 • Tap the “Turn on backlight when a button is pressed or the screen is tapped” check box.
67 Resetting the Device There are three kinds of reset that you can perform on your device when the device’s operating system stops responding or the system becomes corrupted. Depending on the situation, a warm boot, clean boot, or cold boot can be performed. Warm Boot You may have to perform a warm boot if the device freezes (i.e., device no longer responds to the buttons on the screen).
68 Chapter 5 Customizing PA500 Clean Boot A clean boot allows your device to load the main operating system and perform diagnostic tests to determine the boot process problems. To perform a clean boot: 1 Hold down the right and left scanner trigger buttons. 2 While holding down the scanner trigger buttons, gently press the tip of the stylus to the reset button located on the rear of the device. Cold Boot A cold boot will cut off power to your device.
69 Viewing Flash ROM Files Flash ROM (read-only memory) is a rewritable storage for programs and data files. The benefit of this feature is that files and programs saved in Flash ROM are unaffected by the PA500 power status. To access the Flash Memory files: 1 Connect the device to your computer. See page 30. 2 On your computer, click My Computer > Mobile Device > Flash Storage. To transfer files to Device’s Flash Memory: 1 Connect the device to your computer. See page 30.
70 Chapter 5 Customizing PA500 Adding Programs Adding Programs to Your Device Programs bundled with your device at the factory are stored in Flash ROM. You cannot remove these programs, and you’ll never accidentally lose Flash ROM contents. Software programs and data files added to your PA500 after factory installation can be stored in RAM (random access memory).
71 • 5 If the file is not an installer, you will see an error message stating the program is valid but is designed for a different type of computer. You will need to move this file to your device. If you cannot find any installation instructions for the program in the Read Me file or documentation, use ActiveSync Explore button to copy the program file to the Program Files folder on your device. For more information on copying files using ActiveSync, see page 44.
72 Chapter 5 Customizing PA500 2 On the Personal tab, tap Menus. 3 Select the check box for the programs you wish to add. If you do not see the program you want, you can either use File Explorer on your device to move the program to the Start Menu folder, or use ActiveSync on your computer to create a shortcut to the program and place the shortcut in the Start Menu folder. 4 Tap OK.
73 3 Open the path: Windows | Start Menu | Programs. 4 Tap and hold the program you want to add to the menu, then tap Cut on the pop-up menu. 5 Open the path: Windows | Start Menu.
74 Chapter 5 Customizing PA500 6 Tap and hold a blank area of the screen, then tap Paste on the pop-up menu. 7 A Confirm File Move dialog box appears, tap Yes. The program will now appear on the Start menu. To add a Start menu program using ActiveSync on your computer: 1 In the ActiveSync on your computer, click Explore to explore your device’s files and locate the program. 2 Right-click the program, and then click Create Shortcut. 3 Open the path: Mobile Devices | Windows | Start Menu.
75 your computer. Removing Programs 1 Tap Start > Settings. 2 On the System tab, tap Remove Programs. 3 Tap the program you wish to remove. 4 Tap the Remove button. If the program does not appear in the list of installed programs, use File Explorer on your device to locate the program: 1 Tap and hold the program. 2 Tap Delete on the pop-up menu.
76 Chapter 5 Customizing PA500
77 Chapter 6 Regulatory and Safety Notices This chapter lists the specifications and regulatory and safety notices of PA500.
78 Chapter 6 Regulatory and Safety Notices Input/Output Scan Engine Connectivity Wireless connectivity • Light Source: Visible Laser Diode(VLD) 650 nm. • Min. print contrast: 25% absolute dark/light reflectance at 650 nm • Power Consumption: 65 mA typical@5 V • USB port • SDIO/MMC slot • Bluetooth • Version: 1.1 and 1.2 with class 2 specification • Peak output power: 2 ±2 dBm • Frequency band: 2400-2483.5 MHz • Operating channels: 79 Channels • Modulation Type: GFSK • WLAN (802.11b) • 802.
79 Power Main battery Standard battery: 3.7 V, 2200 mAh Battery life 6 hours Battery charge • 3.5 hours with external AC adapter • 3.5 hours with docking station Backup battery One hour data retaining time when main battery is removed Power management • Provide all voltage outputs required in this terminal • Retain memory content more than 72 hours after automatic low battery shutdown • Provide 6 hours operating time with a standard battery.
80 Chapter 6 Regulatory and Safety Notices Barcode/Symbology Barcode Scanner Symbol SE950 Symbology • Bookland EAN • Codabar • EAN 8 • Interleaved 2 of 5 • • Code 11 Code 128 • Label Code IV & V • MSI/Plessy • • • Code 32 (Pharmacy Code) Code 39 • • Code 93 Delta Code • Standard 2 of 5/ Toshiba (China Postal Code) group Telpen • UPC A • EAN 128 • UPC E • EAN 13 • UPC/EAN group OS and Software Programming Tools OS Language Support Microsoft Windows Mobile 5.
81 Regulatory Compliance Statements FCC Statement This is a FCC Part 15 Class B product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian Compliance Statement This Class B Digital apparatus meets all requirements of the Canadian Interferance-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.
82 Chapter 6 Regulatory and Safety Notices
83 Index check main battery status reset device 67 save battery life 63 view Flash ROM 69 A accessories 2 accessory program Scan2Key 56 Scanner Settings 57 adding programs from Internet 71 to Start menu 71 using ActiveSync 70 B battery pack installing 9 Bluetooth 47 activate 47 create partnership receive items 49 send items 49 D device charge 9 E European Conformity Statement exchange files using ActiveSync 44 F 47 C Canadian Compliance Statement 81 charge 9 charge device docking station 10 USB ch
84 Index Internet 53 connect 53 introduction 1 L laser information 81 laser scanner 17 LED status 12 M manage programs 55 accessing 55 accessory programs 56 opening a program 55 switching between programs Microsoft ActiveSync installing 29 system requirements 29 55 N notice ii battery charge ii storage and safety ii O options Bluetooth 32 infrared 32 USB 32 WiFi 32 R regulatory compliance statements Canadian Compliance 81 European Conformity 81 FCC 81 laser information 81 regulatory notice 77 remov
85 V W VPN WiFi set up 51 set up 50
86 Index
