Wearable 2D Ring Scanner - MS652Plus - User's Manual Version 1.0 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. All product and company names are trademarks, service marks, or registered trademarks of their respective owners.
Change Log Date Change Description Version 2019/3/21 first published version 1.0 © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. All product and company names are trademarks, service marks, or registered trademarks of their respective owners.
MS652Plus User’s Manual Preface About This Manual Thank you for purchasing the unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice.
MS652Plus User’s Manual 1. 2. 3. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting.
MS652Plus User’s Manual European Conformity Statement unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive, the EMC 2014/30/EU directive and the Low Voltage 2014/35/EU directive. The declaration of conformity is available for download at : https://portal.unitech.
MS652Plus User’s Manual Waste electrical and electronic equipment (WEEE) unitech has set up a policy and process to meet the EU directive 2002/96/EC and update 2003/108/EC concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitech’s resellers, you shall either contact your local supplier or visit us at : https://portal.unitech.eu/public/WEEE iv © 2019 unitech Electronics Co., Ltd.
MS652Plus User’s Manual Taiwan NCC Warning Statement 低功率電波輻射性電機管理辦法 第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者 均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有 干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備 之干擾。 注意事項: 1. 使用過度恐傷害視力。 2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過 1小時。 3. 減少電磁波影響，請妥適使用。 v © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
MS652Plus User’s Manual Laser Information The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
MS652Plus User’s Manual Battery Notice 1. To guarantee optimal performance, it is recommended that rechargeable batteries be replaced every year, or after 500 charging cycles are completed. It is normal for the battery to balloon or expand after one year or 500 cycles. Although it does not cause damage, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures. 2.
MS652Plus User’s Manual CAUTION! RISK OF EXPLOSION IF BATTERY IS REPLACED INCORRECTLY. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 如果更換不正確之電池行事會有爆炸的風險 請依製造商說明書處理用過之電池 如果更换不正确之电池行事会有爆炸的风险 请依制造商说明书处理用过之电池 Battery charge notice It is important to consider temperature when the battery pack is charging. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 0°C to 40°C.
MS652Plus User’s Manual Storage and safety notice Although charged batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Batteries may be stored at temperatures between -20°C to 60°C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature. * The message above only applies to the usage of the removable batteries.
MS652Plus User’s Manual Adapter Notice 1. 2. 3. 4. Please do not leave the power adapter in the socket when it is not connected to your unitech product for charging. Please remove the power adapter when the battery is fully recharged. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product.
MS652Plus User’s Manual Worldwide Support unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan – Headquarters Europe Tel: +886-2-89121122 Tel: +31-13-4609292 E-mail: info@hq.ute.com E-mail: info@eu.ute.com Address: 5F, No.
MS652Plus User’s Manual Warranty Policy The items covered under the unitech Limited Warranty are free from defects during normal use. The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.
MS652Plus User’s Manual Table of Contents Preface...........................................................................................................i About This Manual ........................................................................................ i Regulatory Compliance Statements .............................................................. i Laser Information ........................................................................................ vi LED Information ....................
MS652Plus User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the MS652Plus gift box. If something is missing or damaged, please contact your unitech representative.
MS652Plus User’s Manual 1.2 Product Detail ￭ Scanner Detail Battery Latch Velcro strap Scan Window Trigger Key ( can be rotated ) LED indicator Buzzer Hole Micro USB port Hand Strap Hole (with Protective Cover ) Charging Contact PIN - 2 - © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. All product and company names are trademarks, service marks, or registered trademarks of their respective owners.
MS652Plus User’s Manual 1.3 Specifications System Connection Connect to host with Windows, Android, or iOS Memory 7.
MS652Plus User’s Manual Protocol HID / SPP Mechanical Scanner Dimension 50 x 71 x 21 mm Scanner Weight 95g Trigger Switch Life 1 million times Functionality Symbologies 1D: All major symbologies and PDF417 2D: QR Code, Data Matrix, Aztec Code, PDF417, Macro PDF417, Micro PDF417, MaxiCode, Codablock A, Codablock F, GS1Composite, Han Xin Code, Australian Post, British Post, Canadian Pos, InfoMail, Intelligent Mail Bar Code, Japanese Post, KIX (Netherlands) Post, GS1 Composite, Korea Post, Planet Code
MS652Plus User’s Manual Storage Temperature -20°C to 60°C ( -4°F to 140°F ) Relative Humidity 95% non-condensing Charging Temperature 40°C ( 104°F ) Regulatory Approvals CE, FCC, BSMI, VCCI, TELEC, NCC, BQB - 5 - © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. All product and company names are trademarks, service marks, or registered trademarks of their respective owners.
MS652Plus User’s Manual 1.4 Getting Started 1.4.1 How to disassemble the trigger module Simply use your finger to press down the release button and rotate it counterclockwise to remove the trigger module. 1.4.2 How to assemble the trigger module Step .1 Find the release button on MS652Plus Step 2. Align the four grooves from the trigger module with MS652Plus, also make sure arrows from both sides are close together. Please adjust the arrow alignment as shown in the photo below.
MS652Plus User’s Manual Then use the trigger module to press down the release button and rotate it clockwise until you hear a clicking sound and the button stays in between the gap of the trigger module. And MS652Plus is ready to go. For hand preference, there are two gaps for users to swap the trigger key location for left click or right click. Right handed users Left handed users (trigger key is on the left ) (trigger key is on the right ) - 7 - © 2019 unitech Electronics Co., Ltd.
MS652Plus User’s Manual 1.4.3 How to change finger rubber pad There are two finger pads for users to choose in order to adjust fingers in a comfortable way. Step 1 : Untighten the velcro band on trigger module. Step 2 : Choose one of the finger pads, put it on the trigger module and stick into the groove on four edges to fix the finger pad. - 8 - © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
MS652Plus User’s Manual 1.4.3.1 How to use double sided tapes on rubber pads To make the rubber pad firmly fix on the on trigger module, we provide a double sided tape for users to use. Please choose the rubber pad that you will use the most frequently. Once you attach this double sided tape onto the rubber pad, it cannot be removed easily due to its strong adhesion. Step 1: Slightly hold the tip of the release paper and peel off the brown protective film and attach it to the trigger module.
MS652Plus User’s Manual Step 2 : Grab the tip of the release paper and to peel it off from the trigger module. Step 3 : Put the finger pad on the trigger module and stick into the groove from four edges to fix the finger pad. Notice : We also provide another double sided tapes for users to practice beforehand. These types of tapes are easily removed. - 10 - © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
MS652Plus User’s Manual 1.4.4 How to change the battery Step 1 : Use your thumb to press down the latch, the battery will automatically jump out, and then you can remove the battery. Step 2 : To install the battery, slide the battery and press down the battery to secure it until you hear the clicking sound. - 11 - © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
MS652Plus User’s Manual 1.4.5 How to put on MS652Plus Step 1. Pull open the velcro band and insert your index finger and middle finger through the loop. Step 2. Adjust and tighten the velcro band for a comfortable fit. Step 3. Clench your fist and use your thumb to tap the trigger key. Step 4. Aim at the barcode you wish to scan. - 12 - © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
MS652Plus User’s Manual 1.5 Battery Charging 1. Flip open the micro USB port on the scanner. 2. Insert the micro USB connector into the port on the scanner and USB A connector into a USB port on the host PC. 3. Keep charging until the red LED indicator turns off. 1.6 Trigger Key Functions 1. Power On: Press & Hold > 1 second 2. Power On & Enter BT Pairing Mode: Press & Hold > 5 seconds 3. Power Off: Press & Hold for 5 seconds until you hear a beep. 4.
MS652Plus User’s Manual 1.
MS652Plus User’s Manual Action/Status Beep / Sound Auto Operation Mode Power On with 1 Beep Wedge Operation Mode Power On with 2 Beeps Batch Operation Mode Power On with 3 Beeps Auto Power Off Alarm 3 short beeps at 15 seconds before power off Power Off Short beep Good Read with BT Connected Beep with medium sound USB Drive Connection Beep with low-medium-high sound USB Drive Disconnection Beep with high-medium-low sound System Setting with Shorter Processing Time Beep with high-low sound
MS652Plus User’s Manual Chapter 2 - Installation 2.1 Pairing For The First Time Use 2.1.1 NFC Pairing with Mobile Devices ( only applicable in BLE Mode) Step 1. Ensure your mobile device supports NFC and that it is enabled. Step 2. MS652Plus will automatically enter BT pairing mode. Step 3. Turn both NFC & Bluetooth on your mobile device. Step 4. Touch near the unitech logo area of the MS652Plus scanner to your mobile phone, until the device prompts to accept pairing. Step 5.
MS652Plus User’s Manual 2.1.2 Pairing with Mobile Devices (w/o NFC) Step 1. Go to your host device settings and turn the Bluetooth function on. Step 2. MS652Plus will automatically enter BT pairing mode. Step 3. The MS652Plus will appear on your device as “MS652Plus-XXXX.” Step 4. Select “MS652Plus-XXXX.” Step 5. Open a word processing program such as Microsoft Word or Notepad and scan the following barcode. If the word “unitech” appears on the screen you have successfully installed your scanner. 2.1.
MS652Plus User’s Manual 2.2 How To Unpair Scan below bar code to unpair MS652Plus with one device before pairing with another new device. 1. If MS652Plus is connected to a host, un-pair will not work. Please remove pairing or turn bluetooth® off from the host side first & try again. 2. If there is trouble to remove pairing on host device, turn off MS652Plus & try again. After pairing on host is removed, scan ‘BLE Un-Pair/Pair’ for new pairing.
2.3 Connection MS652Plus User’s Manual 2.3.1 To Synchronize Date & Time with Host Step 1. Connect MS652Plus as USB drive to host Step 2. Open file 'Config.txt' Step 3. Use 'Save As' to save file 'Config.txt' without name change to USB Drive Step 4. Eject/Disconnect USB drive from host 2.3.2 Rename device Step 1. Connect MS652Plus as USB drive to host Step 2. Open file 'Config.txt' Step 3. Change default device name = "MS652Plus_XXXX" to = "New_Device_Name" Step 4. Max.
