2D Imager Scanner - MS852P - User's Manual Version 1.
Revision History Date Change Description Version 20221011 First Version 1.
Preface About This Manual Thank you for purchasing the Unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice.
1. 2. 3. which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting.
CE RF Exposure Compliance For body-worn operation, this device has been tested and meets the ICNIRP guidelines and the European Standard EN 62209-2, for use with dedicated accessories, SAR is measured with this device at a separation of 0.5 cm to the body, while transmitting at the highest certified output power level in all frequency bands of this device. Use of other accessories which contain metals may not ensure compliance with ICNIRP exposure guidelines.
RoHS Statement This device conforms to RoHS (Restriction Of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. Waste electrical and electronic equipment (WEEE) Unitech has set up a policy and process to meet the 2012/19/EU concerning electronic waste disposal.
Taiwan NCC Warning Statement NCC 警語 取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變 更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響 飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾 時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通信。低功 率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 注意事項: 1. 使用過度恐傷害視力。 2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過 1小時。 3. 減少電磁波影響，請妥適使用。 v © 2022 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Laser Information The Unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1. Class II and Class 2 products are not considered to be hazardous. The Unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
Battery Notice 1. To guarantee optimal performance, it is recommended that rechargeable batteries be replaced every year, or after 500 charging cycles are completed. It is normal for the battery to balloon or expand after one year or 500 cycles. Although it does not cause damage, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures. 2. If a battery performance decreases more than 20%, the battery is at the end of its life cycle.
CAUTION! RISK OF EXPLOSION IF BATTERY IS REPLACED INCORRECTLY. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 電池若未正確更換，可能會爆炸。請原廠建議之同款 電池或同等級的電池來更換。請依原廠指示處理廢電 池。 如果更换不正确之电池行事会有爆炸的风险 请依制造商说明书处理用过之电池 Battery charge notice It is important to consider temperature when the battery pack is charging. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 0°C to 40°C.
Storage and safety notice Although charged batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Batteries may be stored at temperatures between -20°C to 60°C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature. * The message above only applies to the usage of the removable batteries.
Hearing Damage Warning To prevent possible hearing damage, do not listen at high volume levels for long periods. xi © 2022 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Worldwide Support Unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest Unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan – Headquarters Europe Tel: +886-2-89121122 Tel: +31-13-4609292 E-mail: info@hq.ute.com E-mail: info@eu.ute.com Address: 5F, No.
Warranty Policy The following items covered under the Unitech Limited Warranty are free from defects during normal use: The warranty period is varied from each country. Please consult with your supplier or Unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user. xiii © 2022 Unitech Electronics Co., Ltd.
Table of Contents Preface........................................................................................................... i Regulatory Compliance Statements .............................................................. i Laser Information ........................................................................................ vi LED Information .......................................................................................... vi Battery Notice ............................................
MS852P User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the MS852P gift box. If something is missing or damaged, please contact your Unitech representative. The Package Contents Dongle MS852P with battery USB Cable Quick Start Guide Cradle Power Adaptor Optional Accessories Dongle Battery pack 1 © 2022 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
MS852P User’s Manual 1.2 Product Detail 1.2.1 MS852P Product View 2 © 2022 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
MS852P User’s Manual 1.2.2 Cradle details Pairing Barcode Cradle Drain hole Station Mount Screw Holes Interface Port Cable Management Slot 3 © 2022 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
MS852P User’s Manual 1.3 Specifications Optical & Performance Sensor CMOS Sensor, 1280 x 800 pixels Aiming Element 655 nm Laser Illumination One (1) Hyper Red 660 nm LED Skew Angle ± 60° Pitch Angle Sensor ± 60° Roll Angle 360° Optical Resolution 3 mil (code 39), 5 mil (code128), 5 mil (PDF417) Depth of Field Symbology/Resolution Near/Far Code 39: 3 mil 7.6 cm to / 14.7 cm Code 128: 5 mil / 5.8 cm to / 24.9 cm PDF417: 5 mil / 7.6 cm to / 20.1 cm PDF 417: 6.67 mil / 6.3 cm to/ 25.
MS852P User’s Manual Prefix, Suffix, Code ID, Reformatting Date Data Formatting Regulatory Approvals CE, FCC, BSMI, VCCI Communication Radio Unlicensed 2.4GHz Wireless Coverage 10M( line of sight) Interface/ Profile Wireless,SPP & HID profiles Host Interface Supported USB (HID; CDC) Mechanical Dimensions 87.8 L x 71.6 W x 177.7 H (mm) Weight 213g Trigger Switch Life 10 million times Cradle Dimension 120.6 L x 88.7 W x 86.
MS852P User’s Manual 1.4 Getting Started Scanner Turn on : Long press the trigger key for 2 seconds until you hear a long beep sound. Scanner Turn off : Long press the trigger key for about 7 seconds until you hear a short beep sound. 1.4.1 How to pair the scanner with the receiver 1. Long press the trigger key for 2 seconds until you hear a long beep sound to turn on the MS852P. 2. Scan the MAC address on the dongle with MS852P. 3. Insert a dongle into a USB port of the computer or laptop PC. 4.
MS852P User’s Manual 1.4.3 Cradle Function & Operation 1. Charging 2. Update scanner firmware - Cradle button is for updating MS852P firmware - Connect cradle to PC or an adaptor and plug in the socket. - Place the MS852P scanner into the cradle under power off condition. Press and hold the cradle button and MS852P trigger key for around 2 seconds, release after you hear beeper sound. It means MS852P scanner has enter firmware update process. 7 © 2022 Unitech Electronics Co., Ltd. All rights reserved.
MS852P User’s Manual 1.4.4 Test Open a word processing program such as Microsoft Word or Notepad, and scan the following barcode: If the word “Unitech” appears on the screen, you have successfully installed your scanner. Note: To scan a barcode, make sure the aiming beam crosses every bar and space of the barcode. 8 © 2022 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
MS852P User’s Manual 1.5 Battery Charging Before you use the MS852B for the first time, we strongly recommend charging the battery. It takes approximately 5 hours to fully charge the battery. To charge the scanner with / without a cradle, please follow the instructions below. Please only use the USB type C cable which came with the package. ￭ Charging through USB type C cable To charge MS852B, please connect scanner with host PC through USB type C cable.
MS852P User’s Manual 1.6 How to Replace Battery Please follow the below instruction to replace the scanner battery. with a screwdriver, and take the screw out. 10 © 2022 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
MS852P User’s Manual 4.Place the new battery into the scanner. 5. Lock the battery cap with a screw using screwdriver tightly. 11 © 2022 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
MS852P User’s Manual 1.7 LED / Beeper Indicator 1.7.
MS852P User’s Manual 1.7.2 Scanner Beeper indicator Beeper Description Indication Scanner in Auto Operation Mode Power On with 1 Beep Scanner in Wedge Operation Mode Power On with 2 Beeps Scanner in Batch Operation Mode Power On with 3 Beeps Auto Power Off Alarm 3 short beeps at 15 seconds before power off Power Off Short beep Good Read with BT Connected Beep with medium sound Good Read with BT Disconnected Beep with short medium-high sound BT Connection Beep with low-medium-high sound 1.
