Wireless Pocket 2D Imager Scanner - MS920 - User's Manual Version 2.0 © 2014 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
Table of Contents Chapter 1 Overview............................................................................................................ 1 Package Contents...................................................................................................1 Scanner Detail........................................................................................................2 Getting Start............................................................................................................
HID Keyborad Character Delay............................................................................ 11 HID Keyborad Block Delay...................................................................................12 HID Keyborad Case..............................................................................................12 HID Keyborad Languages.....................................................................................13 Enter BT Pairing Code.................................................
Standard 2 of 5.....................................................................................................71 Telepen.................................................................................................................75 Chapter 4 Operating Settings............................................................................................ 78 Pre-defined trigger modes....................................................................................78 Scanning / Triggering............
Overview Package Contents Please make sure the following contents are in the MS920 carton. If something is missing or damaged, please contact your Unitech representative MS912 scanner Resource CD Quick Guide USB Charging Cable Hand Strap Battery NOTE: 1. The scanner’s default power off (idle mode) time is 3 minutes. 2. Please charge scanner for at least 2 hours prior to initial use.
Scanner Detail Getting Started To scan a barcode, make sure the aiming beam crosses every bar and space of the barcode.
BATTERY CHARGING 1. Flip up the rubber cover to expose the mini USB port on the scanner. 2. Insert the mini USB connector into the port on the scanner and the standard USB connector of the USB cable into a USB port on the host PC.
Specifications Light source Illumination: Highly visible white LED Aiming : 617 nm red LED Scan rate 240 scans/sec Sensor Linear CMOS sensor Resolution 1D codes 0.1 mm (4 mils) 2D codes 0.167 mm (6.
Chapter 2 Bluetooth Function Setting Pairing With PC/Notebook For The First Time PC (HID mode) Following steps are based on Microsoft Windows 7. 1. Use MS920 to scan barcode “HID”. 2. Open Devices and Printers by clicking the Start button , and then, on the Start menu, clicking Devices and Printers. 3. Click Add a device, and then follow the instructions. 4. Click the Bluetooth enabled device (Unitech BT XXXXXX) you want to add to your computer, and then click Next.
PC (SPP mode) Following steps are based on Microsoft Windows 7. 1. Use MS920 t0 scan barcode “SPP”. 2. Open Devices and Printers by clicking the Start button the Start menu, clicking Devices and Printers. , and then, on 3. Click Add a device, and then click the Unitech AXXXXXX icon. 4. Open HyperTerminal, and select ingoing com part to make connection. 5. After one beep, start the scan then. Buffer Mode Auto Batch* Inventory No Buffer No Buffer saved in the memory.
Switching Between HID and SPP Mode From SPP to HID If your MS920 is on SPP mode: 1. Go to Devices and Printers under Control Panel, remove the MS920. 2. Use MS920 to scan the barcode “HID”. 3. Undertake the procedure of searching new device, and then select device (Unitech BT XXXXXX) and make pairing. From HID to SPP If your MS920 is on SPP mode: 1. Scan the barcode “BT Un-pair”. 2. Scan the barcode “SPP”. 3. Undertake the procedure of searching new device, and then select MS920 and make pairing. 4.
Factory Default Display F/W Version BT Un-pair iOS Keypad Press the trigger once will display the keypad, press twice will be disappeared. Inventory Space Left Beep on Good Road (Toggle) Check the memory size.
Buffer Erasing Inventory Mode Batch Mode 2. Scan (Erase) 2. Scan (Erase) 1. Scan (Erase Inventory Buffer) . 1. Scan (Erase Batch Buffer) For detail information about barcodes, please refers to section 5. Appendix Bar Code Configuration And Commands. Erase Previous Entry Erase the last data.
Power Saving Enabled* (Good for scan with trigger) Disabled (Good for continuous scanning) BT Module Power Saving (Power off BT while no activities) 1 Minute* 3 Minutes 5 Minutes - 10 -
HID Keyborad Character Delay 1 ms 5 ms 10 ms 20 ms 50 ms 100 ms - 11 -
HID Keyborad Block Delay 10 ms 50 ms 100 ms 500 ms 1 Sec. 3 Sec.
HID Keyborad Languages US English UK English Swiss Swedish Norwegian Italian German French Danish Partial ALT Japanese Spanish ALT Mode - 13 -
Enter BT Pairing Code Enter Abort To scan "//7" label to enter code input mode, to scan "digit" as prompted on host, to scan "$M" to finish input and exit input mode. To scan "$P" to abort input and exit input mode.
Chapter 3 Symbologies - Symbology = bar code type or family (e.g. Code 39, UPC, EAN). - Activate the symbologies you need and modify the settings for your symbologies if required. - To optimize performance, only activate symbologies you need !!! (deactivate the Code 39 and EAN/UPC default symbologies if you don't need them. Disable all symbologies - Deactivates all the symbologies activated. - Use the "not active" options to deactivate individual symbologies.
Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters) B7 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission.
A, B, C, D Check digit check digit verification - AIM has a recommended check character for Codabar - Each Codabar data character (including Start/Stop) has a value assigned to it: 0=0 1=1 2=2 3=3 4=4 5=5 6=6 7=7 8=8 9 = 9 - = 10 $ = 11 : = 12 / = 13 , = 14 + = 15 A = 16 B = 17 C = 18 D = 19 - The values are added and the check is calculated: check = [(next multiple of 16) - (sum of assigned AIM values)] Example data characters: A01234B AIM values = 16 + 0 + 1 + 2 + 3 + 4 + 17: next multiple of 16: 43
Enable Barcode length - Use the L1 as minimum length option if you know the minimum length of the codes in your application!!! - To optimize decoding performance and increase security, select the same length as the minimum length in your application (do not select a shorter length!!). Length = [start] + [barcode data] + [check digit] + [stop] - Minimum length possible = 3 characters. - If the codes in your application have fixed lengths, use barcode length mode "L1, L2, and L3 as fixed lengths.
Set lengths 1, 2 and 3 - Set barcode length L1, L2 and L3 according to the barcode length mode used. Compose L1: Compose L2: Compose L3: Codablock - 2-dimensional alphanumerical symbology Codablock A Disable (*) Enable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
K1 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission. - Use the default value or compose your code mark for this symbology (1 character). *(*) Compose: Please refer to SCM (Software Configuration Manager) in CD Codablock F Disable (*) Enable Symbology identifier User defined - User defined symbology identifier.
K1 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission. - Use the default value or compose your code mark for this symbology (1 character). *(*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code 11 - numerical symbology Disable(*) Enable Symbology identifier User defined - User defined symbology identifier.
C1 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission. - Use the default value or compose your code mark for this symbology (1 character).
Barcode Length - Use the L1 as minimum length option if you know the minimum length of the codes in your application!!! - To optimize decoding performance and increase security, select the same length as the minimum length in your application (do not select a shorter length!!). Length mode - L1 = Codes with as many characters as specified by L1 and longer are read (L2 and L3 are not used). - L2 = Only codes that comply with the lengths specified by L1, L2, and L3 will be read.
Compose L2: Compose L3: Code 39 - Alphanumeric symbology. - Letter case not defined - transmitted in upper case. - Format: standard 43 characters (default) or full ASCII (see "format" for lists). Disable Enamle(*) Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission. - Use the default value or compose your code mark for this symbology (1 character).
'$' only '$' only *' Check digit check digi verification Disable (*) Modulo 43 French CIP Italian CPI check digi transmission - You can chose to transmit or not transmitted the check digit.
Enable Barcode length - Use the L1 as minimum length option if you know the minimum length of the codes in your application!!! - To optimize decoding performance and increase security, select the same length as the minimum length in your application (do not select a shorter length!!). Length = [start] + [barcode data] + [check digit] + [stop] - Minimum length possible = 3 Length mode - L1 = Codes with as many characters as specified by L1 and longer are read (L2 and L3 are not used).
Set lengths 1, 2 and 3 - Set barcode length L1, L2 and L3 according to the barcode length mode used. Compose L1: Compose L2: Compose L3: Reading range - Applies a special algorithm for long-distance reading (default setting). - Use the "normal" setting if distance reading is not required. Extended (*) Normal Reading tolerance - Sets the tolerance level for reading hard to read bar codes. - High = most permissive (reads codes of variable quality).
High (*) Medium Low Unconventional Code 39 - Used for decoding unconventional Code 39 such as: - very large inter-character - large ratio between narrow and wide elements Disable (*) Enable Special keys interpretation - Special keyboard keys such as [Enter] and [Tab] (see list below) can be interpreted and transmitted by using dual-character combinations. - This function is also compatible with the Code 39 full ASCII format.
Enable Code 93/ Code 93i - Code 93 Alphanumeric full ASCII symbology - letter case defined. - Code 93i (encompasses and extends Code 93) Alphanumeric, full and extended ASCII, all Unicode characters, etc Disable Enable (*) Symbology indentifier User Defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission.
Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission. - Use the default value or compose your code mark for this symbology (1 character).
L1 as min, L2 as max Set lengths 1, 2 and 3 - Set barcode length L1, L2 and L3 according to the barcode length mode used. Compose L1: Compose L2: Compose L3: Code 128 / GS1-128 - Alphanumeric full ASCII symbology - letter case defined. - "GS1-128" = Code 128 with the FNC1 character in the first position.
GS1 - 128 disable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
GS1 128 D (*) Compose: Please refer to SCM (Software Configuration Manager) in CD GS1 - 128 identifier - The ]C1 AIM identifier for GS1-128 is automatically added by default in front of GS1-128 bar codes. Enable (*) Disable Barcode length - Use the L1 as minimum length option if you know the minimum length of the codes in your application!!! - To optimize decoding performance and increase security, select the same length as the minimum length in your application (do not select a shorter length!!).
L1 as Minimal length (*) L1, L2, L3 as fixed length L1 as min, L2 as max Set lengths 1, 2 and 3 - Set barcode length L1, L2 and L3 according to the barcode length mode used.. Compose L1: Compose L2: Compose L3: Reading tolerance - Sets the tolerance level for reading hard to read bar codes. - High = most permissive (reads codes of variable quality).
High (*) Medium Low Reading range - Applies a special algorithm for long-distance reading (default setting). - Use the "normal" setting if distance reading is not required. Extended (*) Normal ISBT 128 - International Society of Blood Transfusion - Activating ISBT 128 deactivates Code 128 / GS1-128 (to avoid confusion with Code 128 / GS1-128). - You can re-activate Code 128 or GS1-128 by using the corresponding setup command if desired.
Disable (*) Transmit Disable (*) Only transmit concatenated codes Transmit concatenated codes or single codes Concatenate Disable (*) Enable DataMatrix - Two-dimensional symbology. - Only available with models equipped with an area imager. - Can encode up to approximately 2000 characters. - Negative image DataMatrix supported. - Mirror image DataMatrix not supported.
Disable Enamle (*) Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
Mirrored labels activation - When enabled mirrored labels can be read as well as normal labels. - When disabled only normal labels can be read.
EAN / UPC - Numerical symbology.
UPC - E1 - Irregular UPC-E with number system equal to 1 (usually the first printed character). - UPC-E must be active for UPC-E1 to be taken into account. Disable (*) Enable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
EAN-8 FF (*) Compose: Please refer to SCM (Software Configuration Manager) in CD EAN-13 F (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission. - Use the default value or compose your code mark for this symbology (1 character).
Compose: Please refer to SCM (Software Configuration Manager) in CD EAN-13 F (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Add - on digits not required but transmitted if read (*) required and transmitted add-on 2 Disable (*) Enable add-on 5 Disable (*) Enable - 43 -
security level 10 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Check digit transmission [leading character] [number system] [data] [check digit] UPC-A Enable (*) Disable UPC-E Enable (*) Disable EAN-8 Enable (*) Disable - 44 -
EAN-13 Enable (*) Disable UPC number system [leading character] [number system] [data] [check digit] UPC-A Enable (*) Disable UPC-E Enable (*) Disable - 45 -
Re-encoding UPC-A, UPC-E, EAN-8 [leading character] [number system] [data] [check digit] - Converts decoded data to other code formats. - Transmission only takes into account the parameters available for the target bar code format. - Regular UPC-A has a transmitted number system equal to 0. - To transmit the additional leading character (country code), select the "UPC-A transmitted as EAN-13" option.
ISBN - International Standard Book Number - EAN-13 code, the first 3 characters "978" or "979" (except for "9790") are ignored and the checksum (0..9, "X") is calculated on the remaining characters.
Enable Reading range - Applies a special algorithm for long-distance reading (default setting). - Use the "normal" setting if distance reading is not required. Normal Extended (*) GS1 DataBar (RSS) - Also known as Reduced Space Symbology (RSS). Omni-directional - Numerical symbology.
Disable (*) Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters). C3 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission.
Disable (*) Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters). C4 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission.
Enable Disable (*) Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
Interleaved 2 of 5 - Numerical symbology. - For GTIN compatibility set barcode length to one fixed length of 14 characters. Disable (*) Enable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
Compose: Please refer to SCM (Software Configuration Manager) in CD Check digit - Especially recommended for variable length Interleaved 2 of 5 and if "consecutive same read data validation" (data decoding security parameters) is not activated.
- For GTIN compatibility set barcode length to one fixed length of 14 characters - compose 1 or 2 or 3 fixed lengths provides the best performance and security if the codes in your application have fixed lengths Length mode - L1 = Codes with as many characters as specified by L1 and longer are read (L2 and L3 are not used). - L2 = Only codes that comply with the lengths specified by L1, L2, and L3 will be read.
Compose L3: Reading tolerance - Sets the tolerance level for reading hard to read bar codes. - High = most permissive (reads codes of variable quality). - Low = least permissive (only reads high quality codes that meet official Code 39 standards) - Quiet zone verification (space before and after bar code to ensure correct decoding). High (*) Medium Low Matrix 2 of 5 - Numerical symbology.
Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters). B4 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission.
ChinaPost - Specific start/stop characters (not transmitted) and checksum (transmitted). ChinaPost Barcode length - Use the L1 as minimum length option if you know the minimum length of the codes in your application!!! - To optimize decoding performance and increase security, select the same length as the minimum length in your application (do not select a shorter length!!). Length = [barcode data] - Minimum length possible = 3 characters.
Set length L1, L2 and L3 - Set barcode length L1, L2 and L3 according to the barcode length mode used. Compose L1: Compose L2: Compose L3: MaxCode - Two-dimensional alphanumerical symbology used by UPS. - Only available with models equipped with an area imager. Disable (*) Enable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission.
D2 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission. - Use the default value or compose your code mark for this symbology (1 character). * (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Mode 0 - This mode is obsolete. - We do not recommend using this mode.
MicroPDF417 - Two-dimensional symbology. - Alphanumeric full ASCII symbology - letter case defined. - It is highly recommended to select "stacked codes" in sensor optimization (see Operating settings/read optimization). Disable (*) Enable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission.
* (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code 128 emulation - When active and reading a MicroPDF code containing a special flag, the scanner transmits the Code 128 AIM symbology identifier instead of the MicroPDF symbology identifier ( ]C instead of ]L ) Disable (*) Enable MSI Code - Numerical symbology. Disable (*) Enable Symbology identifier User defined - User defined symbology identifier.
- Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters). B8 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission. - Use the default value or compose your code mark for this symbology (1 character).
Disable Barcode length - Use the L1 as minimum length option if you know the minimum length of the codes in your application!!! - To optimize decoding performance and increase security, select the same length as the minimum length in your application (do not select a shorter length!!). Length = [barcode data] + [check digit] - Minimum length possible = 2 characters. Length mode - L1 = Codes with as many characters as specified by L1 and longer are read (L2 and L3 are not used).
Compose L1: Compose L2: Compose L3: PDF 417 - Set barcode length L1, L2 and L3 according to the barcode length mode used. Enable (*) Disable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission. - Use the default value or compose your code mark for this symbology (1 character).
Plessey Code - Numerical symbology. Disable (*) Enable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
Check digit transmission [leading character] [number system] [data] [check digit] Disable (*) Enable Unconventional stop Disable (*) Enable Barcode length - Use the L1 as minimum length option if you know the minimum length of the codes in your application!!! - To optimize decoding performance and increase security, select the same length as the minimum length in your application (do not select a shorter length!!).
- L3 = Codes at least the length specified by L1 and no longer than the maximum length specified by L2 are read (L3 is not used). L1 as Minimal length (*) L1, L2, L3 as fixed length L1 as min, L2 as max Set length L1, L2 and L3 - Set barcode length L1, L2 and L3 according to the barcode length mode used. Compose L1: Compose L2: Compose L3: QR Code - Two-dimensional matrix symbology. - Only available with models equipped with an area imager.
- Offers three levels of error detection. - Activating QR Code activates Model 2. Use the Model 1Control activation if you are using Model 1 (not supported by all scanners). - Negative image QR Code not supported. Disable (*) Enable Model 1 control - Enables the decoding of Model 1 QR codes. Disable (*) Enable Inverse video - Normal = used for decoding black bar codes printed on white background. - Inverse = used for decoding white bar codes printed on black background.
Automatic MicroQR activation - Micro QR is a small QR code with only one pattern. Disable (*) Enable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
* (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Structured append Disable (*) Enable Header transmission Disable (*) Enable Standard 2 of 5 - Numerical symbology. - Default format = Identicon (6 start/stop bars). - Also referred to as "Straight 2 of 5" and "Industrial 2 of 5.
Enable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters). B5 (*) Compose: Please refer to SCM (Software Configuration Manager) in CD Code mark - See "Data transmission settings - symbology identifier - code mark" to activate or deactivate code mark transmission.
Computer Identics Check digit Check digit verification Disable (*) Modulo 10 Check digit transmission - You can chose to transmit or not transmitted the check digit. Disable (*) Enable Barcode length - Use the L1 as minimum length option if you know the minimum length of the codes in your application!!! - To optimize decoding performance and increase security, select the same length as the minimum length in your application (do not select a shorter length!!).
(L2 and L3 are not used). - L2 = Only codes that comply with the lengths specified by L1, L2, and L3 will be read. - L3 = Codes at least the length specified by L1 and no longer than the maximum length specified by L2 are read (L3 is not used). L1 as Minimal length (*) L1, L2, L3 as fixed length L1 as min, L2 as max Set length L1, L2 and L3 - Set barcode length L1, L2 and L3 according to the barcode length mode used.
Telepen - Alphanumeric full ASCII symbology - letter case defined. - Default format = ASCII. Disable (*) Enable Symbology identifier User defined - User defined symbology identifier. - See "Data transmission settings - symbology identifier - UDSI" to activate or deactivate UDSI transmission. - Use the default value or compose your custom symbology identifier for this symbology (1 - 4 characters).
Format ASCII (*) Numeric Barcode length - Use the L1 as minimum length option if you know the minimum length of the codes in your application!!! - To optimize decoding performance and increase security, select the same length as the minimum length in your application (do not select a shorter length!!). Length = [barcode data] - Minimum length possible = 1 characters.s. Length mode - L1 = Codes with as many characters as specified by L1 and longer are read (L2 and L3 are not used).
L1 as min, L2 as max Set length L1, L2 and L3 - Set barcode length L1, L2 and L3 according to the barcode length mode used.
Chapter 4 Operating Settings - Settings that affect the way your product operates (trigger settings, flashing mode, data decoding security settings, beep characteristics, etc.). Pre-defined trigger modes - These are pre-defined trigger settings used to quickly set up your scanner. - If you are using a pre-defined mode, do not set the other Scanning/triggering settings. Toggle - One pull turns on the aimer only. When the trigger is released, illumination and decoding turn on.
Aim Scanning / Triggering Triggering modes Continuous - At power up the lighting and decoding are on all the time. The trigger is not used. Continuous Level (*) - Lighting and decoding are on when the trigger line is activated (trigger pressed) and off when the trigger line is deactivated (trigger released). Level (*) Pulse - Lighting and decoding are on when the trigger line is activated (trigger pressed) and stay on until a period of inactivity lasting the time specified by the trigger timeout.
- When a bar code is detected, the lighting and decoding automatically turn on and stay on until another period of inactivity (timeout), after the timeout the scanner starts flashing again. Flashing Autostand - Autostand triggering mode switches from Level to Flashing (1D models) or Presentation (2D models). - At power up the scanner is in Flashing or Presentation trigger mode (no need to activate the trigger line). You can put a bar code in front of the scanner and it will be scanned.
- The trigger can be used in Presentation mode - when you pull the trigger the scanner functions as if it were in Level mode. - Only available with 2D models. Presentation Presentation threshold - Only available on 2D models. - Use this setting when in Presentation Triggering mode to regulate how sensitive the imager is to movement which automatically wakes up the scanner. - The higher the value = the stronger the movement is needed to wake up the scanner.
Trigger activation - Used to enable or disable hardware or emulated triggers. IMPORTANT: You cannot activate the trigger line if the hardware trigger is disabled. If you are using level or pulse trigger modes, the only way to re-activate the hardware trigger is by using online set up (ISCP terminal) or sending an ISCP command. Disabled - Hardware and emulated triggers are disabled. The only way to turn the imager on is by sending a decode on/decode off control command (20, 40).
Enabled - Start read character default = STX - Stop read character default = ETX - This option is NOT compatible with ISCP. Enable start character [STX] (*) Compose start character - Use different characters for "start read" and "stop read." - This option is NOT compatible with ISCP. Compose start character stop character [ETX] (*) Compose stop character - Use different characters for "start read" and "stop read." - This option is NOT compatible with ISCP.
Turn off after good read - When active, the scan engine stops the reading session after a successful decoding. - Turn off after good read is only used in the following trigger modes: - Level - Pulse - Autostand - Standard Aim NOTE: this parameter is NOT used with conti Enable (*) Disable Retrigger delay - Only valid if "Turn off after good read" is disabled. - This setting is a time delay in which the scanner turns off after a good read.
- Pulse - Autostand - Toggle* NOTE*: In Toggle trigger mode, "one pull aim, one pull read" does not work as stated. Instead one pull turns on the aimer only. When the trigger is released decoding begins. If no decode, second pull turns aimer and decoding off. Typical aimer (*) One pull aim and read - Pull and hold trigger - aiming beam (programmable duration) then reading beam. One pull aim and read One pull aim, second pull read - First pull aiming beam, second pull reading beam.
- If you wait longer than the duration before the second pull, the cycle starts over with the aiming beam.
Ignore stand detect - Enable ignore stand detect when you want to use Autostand triggering mode with and you are not using a detectable stand (charge base or Bluetooth base station). Disable (*) Enable Double scan prevention - When enabled pulling the trigger a second time does not start a new reading session unless the timeout has expired. This prevents the user from accidentally scanning the same bar code twice.
Data decoding security - Ensures correct transmission of data for difficult reading conditions and varying levels of barcode quality (poorly printed labels, variable lengths and no check digit, "fragile" symbologies). - Increasing the security level reduces the reading speed !!! Predefined security levels - Predefined security level settings can be modified individually - Use medium and high security levels for poor-quality bar codes or critical applications.
Timeout between identical consecutive codes (ms) - Prevents reading the same bar code more than once. - Value is milliseconds. Compose (ms): Timeout between different consecutive codes (ms) - Prevents unwanted reading of other bar codes on the same label. 0 (*) Compose (ms): Center decoding - When enabled the scanner reads only the bar code that the laser aimer is aimed at. - This is helpful when reading bar codes that are positioned close together.
Tolerance - The tolerance level for center decoding allows you to aim the laser close to the bar code to be read rather than be positioned on the bar code. - 0 = No tolerance (laser aimer must be positioned on the bar code to be read), 100 = most permissive (laser aimer can be positioned beside the bar code to be read). No tolerance (*) Compose (%): Bar code sequence - Bar code sequence allows you to read up to 10 bar codes with one trigger pull.
Beeps / LEDs Note (tone frequency) High (*) Medium Low Power-up beeps 2 beeps = successful power-up 3 long beeps = EEPROM integrity error (contact your Intermec representative !). Disable (*) Enable Good read beeps Number - "Normal" bar codes: 1 beep (default) = good read - Configuration codes: 2 beeps = good read, 6 beeps = setup error, 3 long beeps = EEPROM integrity error (contact your Intermec representative !).
1 beep (*) 2 beeps None Duration 60 80 (*) 200 300 Timing - IBM and OCIA cash registers: do not send this parameter online to the scan engine through RS-232 cable 0-364032-10!!! Send it to the setup sheet and read the configuration code with your normal IBM / OCIA product cable connected.
During transmission (*) Before transmission After transmission Good read LED duration - "Read" LED green = "good read" - Setting a duration of 0 ms = "no good read LED" - Value is in milliseconds.
5000 Disable/enable all good read signals - This setting can be used to disable all good read signals: Beep, LED and vibrate.
Multicode beeps - By default the scanner does not beep when reading several bar codes when using the Multicode function (see Symbologies). Use this setting to activate beeps when reading bar codes that are part of a Multicode.
Chapter 5 Data Transmission Settings - Modify data transmission settings to optimize performance. ISCP - MS920 Scanner Control Protocol parameters. ISCP (*) None Data format Raw format - Barcode data is sent without a frame and no acknowledgement is necessary. Raw format Packet format - Data is sent to the host in an ISCP frame. Packet format Extended barcode data format BCD - "Packet" data format must be activated to enable BCD transmission.
- Precedes barcode data with "[BCD]" indicator. BCD BCDEX (*) - "Packet" data format must be activated to enable BCDEX transmission. - Precedes barcode data with "[BCDEX]" indicator and extended BCDEX (*) DPS Transmission frame size (TFS) - Length of the longest frame that can be received by the host. - Value from 32 up to the maximum transmission frame size (MTFS) of the scanner.
- Error (if any) - Type of ISCP bar code (setup, status, etc.) - GID - FID - Parameter - For information on the event frame received by the host see the ISCP online help available in the help menu in Easyset.
Unsuccessful decoding - This event is sent whenever a decode session is deactivated (trigger released) and no decode has taken place.
Enable Trigger pulled Disable(*) Enable Trigger released Disable(*) Enable Wake-up Disable(*) Enable Structured append Disable(*) - 100 -
Enable Symbology identifier [symbology id] [data] Not transmitted(*) AIM format [AIM symbology id] [data] - Activates for all symbologies the 3-character symbology identifier standardized by the AIM Committee. - Example: "] A 0" identifies standard Code 39 without check digit[[[ If the data in a bar code is modified (ISBN, . . .), the standard AIM identifier for the symbology will be replaced by "]X0"]]].
Code Mark [preamble] [code mark symbology id] [data] [postamble] - Activates code mark symbology identifier transmission for all symbologies. NOTE: To change the default values go to "Symbology/select symbology/ symbology identifier/code mark" and use the compose option.
Inter-Character / message delay - Avoids dropping characters if transmitting decoded data too fast for the host system. Inter-Character delay - Do not use for IBM 46xx cash registers or laser/wand emulation!!! - Value is in milliseconds.
Inter-message delay - Value is in milliseconds. 0 (*) 10 30 50 80 100 Data editing - IMPORTANT [[[[ The data editing function is only available with STCDecode version 1.1.5.0 or later ]]]] - Your product can edit the data it receives before it transmits it to the host system. - Define up to 7 input scenarios to intercept the data you want to edit.
- The order in which you define the scenarios is important (the product compares incoming data with each scenario in turn and edits the data for the first matching scenario it finds). 1.Activate the scenario(s) you want the product to detect. 2.Define the input data you want to intercept for editing (any combination of input type, input length, input mask). 3.
Compose barcode length: Compose mask: Scenario 2 Disable (*) Enable Select barcode Type: Compose barcode length: Compose mask: Scenario 3 Disable (*) - 106 -
Enable Select barcode Type: Compose barcode length: Compose mask: Scenario 4 Disable (*) Enable Select barcode Type: Compose barcode length: - 107 -
Compose mask: Scenario 5 Disable (*) Enable Select barcode Type: Compose barcode length: Compose mask: Scenario 6 Disable (*) Enable - 108 -
Select barcode Type: Compose barcode length: Compose mask: Scenario 7 Disable (*) Enable Select barcode Type: Compose barcode length: Compose mask: - 109 -
Chapter 6 Configuration Modes and Utilities Get firmware version - Get version info. Get firmware version Get decode version - Get decode version info. Get decode version Get asub-system versions - Get all component versions. Get asub-system versions Optical setup (using configuration bar codes) - Use configuration bar codes to set up the product. Always enabled - Configuration with bar codes possible all the time.
Always enabled Inhibit after 1 mn - Protects the product against unwanted configuration by bar code. - Configuration with bar codes only possible before end of 1 minute timeout (cycle repeated until no config code read within 1 minute). Inhibit after 1 mn Transparent configuration mode - Allows you to use your scanner to set up other products (setup commands are transmitted to the other product but do not affect your scanner).
Appendix I Worldwide Support Unitech’s professional support team is available to quickly answer questions or technical-related issues. Should an equipment problem occur, please contact the nearest Unitech regional service representative. For complete contact information please visit the Web sites listed below: Region Web Site Global Operation Center http://www.ute.com Unitech Taiwan http://tw.ute.com Unitech Asia Pacific & Middle East http://apac.ute.com http://india.ute.
