PA690 Rugged Mobile Computer - PA690 - User’s Manual 400854G Version 1.0 Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Preface About This Manual This manual explains how to install, operate and maintain the PA690 Rugged Mobile Computer. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice. © Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved.
Regulatory Compliance Statements FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications.
RF Radiation Exposure Statement For body contact during operation, this phone has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of 1.5 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Canadian Compliance Statement This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Laser Information The Unitech PA690 series is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The PA690 series contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
If the main battery is removed, the backup battery ensures the data on SDRAM is safe for up to 2 hours. To prevent data loss, do not leave the PA690 uncharged with the main battery removed for an extended period. See the Charging the Battery unit on for more details. Note: To guarantee optimal performance, it is advised that rechargeable batteries be replaced every year, or when 500 charge/discharge cycles are achieved.
Storage and safety notice Although charged Lithium-Ion batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens they will require recharging prior to use. Lithium-Ion batteries may be stored at temperatures between -20°C to 60°C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature.
Table of Contents Preface About This Manual..........................................................................................i Regulatory Compliance Statements ............................................................. ii FCC Warning Statement ........................................................................... ii FCC Label Statement ............................................................................... ii RF Radiation Exposure Statement............................................
Turning ON the PA690 for the First Time......................................................5 Installing the Battery .....................................................................................6 Charging the Battery ....................................................................................7 Keypads and Function Buttons.....................................................................9 Using Function keys ...............................................................................
Chapter 4 Barcode Scanner Programs........................................................................25 Scanner Setting..........................................................................................25 Scan2Key ...................................................................................................25 Barcode Symbologies.............................................................................26 Barcode Symbologies 2D ..............................................................
x Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 1 Getting Started Introducing the PA690 Thank you for purchasing the PA690 Rugged Mobile Computer. The Unitech PA690 is a rugged handheld computer designed to empower your mobile workforce in today’s aggressive business environment. As productivity and efficiency define the benchmark for success, the PA690 provides field-based workers with a host of data collection tools and a comprehensive wireless communication platform, all in a compact, durable and ergonomic form factor.
Features Powerful system z Microsoft Windows Mobile 6.5 operating system z Marvell PXA320 processor with speed of up to 806 MHz System memory z 256MB Mobile DDR z 512MB NaNDFlash Audio z MIC z Speaker z Receiver (Headphone) Expansion slot z MicroSD memory card slot, supporting up to 32GB Display z 3.8” TFT LCD touch screen Wireless connectivity z WLAN, 802.11a/b/g z WWAN, GSM : HSDPA z 480 (W) x 800 (H) resolution z WPAN, Class II, Bluetooth (WVGA) z Supports display rotation 2.
PA690 Product Introduction & Accessory Kit PA690 Terminal Manual CD Stylus Battery Elastic Stylus String Hand Strap Power Adaptor Plugs 3 Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Tour of the PA690 The following sections describe the main components and features of the PA690. PA690 Front and Right View 1 4 9 10 2 11 12 5 3A 6 3B 7 8 1 LED indicators 7 Power button 2 LCD touch screen 8 Universal connector 3A Microphone 9 Scanner trigger button 3B Reset button 4 Receiver 10 Mute / vibration button* 5 Scan button 11 Camera button 6 Keypad 12 Memory card slot *Note: If you just want Mute, hit the “+ -“ button on the left side of the unit, and then select “OFF”.
PA690 Rear and Left View 1 5 6 2 3 7 8 11 9 12 4 10 1 Barcode scanner window 7 Speaker 2 Earphone jack 8 5M/AF camera 3 Microphone 9 LED flash light 4 Battery compartment 10 Battery compartment tab 5 Antenna 11 Scanner trigger button 6 Stylus 12 Volume up/down Turning ON the PA690 for the First Time After you have initially charged your device for about 16 hours, the device is ready to be used. You can now start up your device.
Installing the Battery WARNING! There is a risk of fire and burns if the battery pack is handled improperly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water. DO NOT attempt to open or service the battery pack. Dispose of used batteries according to local recycling guidelines in your area. A backup battery cell is embedded into your device to prevent data loss when the main battery pack is removed or completely discharged.
5. Replace the battery compartment cover by pushing down on the tabs and sliding them back into place as shown. NOTE: Make sure the battery compartment cover is securely closed, or you may be unable to turn ON the terminal. Charging the Battery Before using the terminal for the first time, you need to charge it for about 16 hours. After that, you can charge the terminal for 4 hours to recharge the battery to full capacity. Charge the terminal using the USB charging cable or the docking station.
3. Plug the AC adapter cord into an electrical outlet (3). Checking the LED status Terminal LED indicators from left to right: -- GPRS/Bluetooth Communication -- Scan -- Power LED Status Description Flashing Yellow GPRS module is enabled. GPRS/Bluetooth Terminal Scan Power Flashing Blue Bluetooth module is enabled.
Keypads and Function Buttons Numeric Keypad Key ~ Description Qwerty Keypad Key Description Power key Escape key Enter key Backspace key Tab key Function key Alpha key, toggle between numeric and alphabetic entry modes Windows key Alphanumeric keys Hang-off key Answer key Left cursor key Right cursor key Up cursor key Down cursor key When the PA690 turns on, the numeric mode is on by default. When you toggle to alpha mode, the CAPS mode is off by default.
Using Function keys For Qwerty Keypad Key Description Key Description + Keypad backlight toggling + Screen backlight toggling + Decrease screen backlight brightness + Increase screen backlight brightness + Softkey 2 + Softkey 1 + END TALK + TALK + Scanner setting + Task manager execution + Device information + Power management For Numeric Keypad Key Description Key Description + Calibration + Screen backlight toggling + Keypad backlight toggling + Power management +
Using Alpha keys Key Alpha Off Alpha On CAPS Off CAPS On 0 Space, @, $, “, 0 Space, @, $, “, 0 1 +, -, \, %, 1 +, -, \, %, 1 2 a, b, c, 2 A, B, C, 2 3 d, e, f, 3 D, E, F, 3 4 g, h, i, 4 G, H, I, 4 5 j, k, l, 5 J, K, L, 5 6 m, n, o, 6 M, N, O, 6 7 p, q, r, 7 P, Q, R, 7 8 t, u, v, 8 T, U, V, 8 9 w, x, y, z, 9 W, X, Y, Z, 9 # ,;!./ ,;!./ 11 Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
12 Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 2 Using the Hardware Using the MicroSD Memory Card PA690 has an expansion slot compatible with a range of MicroSD memory cards, which are primarily used to back up or transfer files and data. Inserting a Memory Card 1. Remove the two screws on the MicroSD slot shield and remove the shield. 2. Insert the MicroSD card with the notched corner as shown. 3. 4. Push the card into the slot until you feel the MicroSD card click into place. Screw the MicroSD compartment cover back into place.
Inserting the SIM card 1. 2. Remove the battery compartment cover and the main battery. Slide the cover of the SIM card slot to the right to release the latch. 3. Pull open the cover with thumb. 4. Insert the SIM card into the cover with the notched corner up, the contact side of the SIM card facing down. 5. Close the cover over the slot, and then slide the cover to the left to lock the SIM card. 6. Put the battery back into the battery compartment and replace the battery compartment cover.
1. Tap Start Settings System 2. Tap the Scanner icon. The Scanner Control Panel appears. NOTE: Or press Func key and “7” simultaneously to bring up the Scanner Control Panel screen. In the Scanner Control Panel screen, you can configure barcode scanner parameters such as enabling or disabling barcode symbologies, setting data transmission options, configuring magnetic and proximity reading options, and setting power management options. See the section of Barcode Symbologies.
16 Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 3 Getting Connected The PA690 enables users to link to a host computer using an RS-232 cable, or Bluetooth, WiFi, or GPRS connection for data communication. This chapter provides an overview of the PA690 communication options. Establishing Device-PC Connection Installing Microsoft ActiveSync In order to exchange data between your computer and the PA690, Microsoft Active-Sync must be installed on your computer.
Connecting the Device to Your Computer 1. After ActiveSync has been installed, connect the PA690 to your PC as described in Connecting the terminal to a host (PC/Notebook). 2. Turn the PA690 on. 3. ActiveSync starts automatically and configures the USB port to work with the PA690. The New Partnership setup wizard automatically starts. NOTE: If ActiveSync doesn’t start automatically, click Start Programs Microsoft ActiveSync.
WiFi Connection A wireless network can be added either when the network is detected or by manually entering network settings. Before following these instructions, make sure if authentication information is needed. Using the Summit Utilities You can use the Summit Client Utility tool to setup or change the WiFi settings. Admin Login 1. Tap Start Setting System Wi-Fi. The Summit Client Utility window appears. 2. To login as an administrator, tap Admin Login. 3. Enter the Admin Password.
4. Tap Profile to scan available APs Scan Available AP 1. Under Profile tab, tap Scan for available AP. 2. You may select a desired AP to create a new profile. Tap Configure. 3. Tap Yes to create the new profile. 20 Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
4. Enter the WEP key or network key. Tap OK. Commit and Activate 1. Tap Commit to activate the setting. 2. Under the Main tab, select the profile you want to activate from the drop-down menu of the Active Profile. 3. Under the Status tab, you can see the IP address, signal strength and quality. 21 Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
4. 5. Tap OK to exit the Summit Client Utility. If you want to disconnect the AP, tap Disable Radio. u-CenterMobile for Quick GPS Connection Before you start to use your device for GPS navigation, use the u-CenterMobile program first to download ephemeris data (current satellite position and timing information) onto your device. This data is needed to accelerate GPS positioning.
2. The u-CenterMobile program appears. To Download Data Please follow the following steps to download the ephemeris data. 1. Tap Rx Autobauding. 2. Tap Rx Port. 23 Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
3. Select COM4. 4. The tool starts to download the ephemeris data (current satellite position and timing information). 5. When the download is finished, you will see the data shown in the upper right corner. 24 Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 4 Barcode Scanner Programs The PA690 provides an option for the barcode scanner, allowing you to scan and decode various types of 1D/2D barcodes. Scanner Setting When it is necessary for the user to change the default barcode symbology for a different application, the Scanner Control Panel provides the ability to change default symbology, place delimiter characters behind scanned data, and save the settings. Tap Start Settings System Scanner. The Scanner Control Panel appears.
Barcode Symbologies Enable / Symbology Disable Barcode Australian Char Check Transmit / Digit Check Others verification Char/digit YES Send bar width data Post British Post YES Canadian YES Post Codabar YES YES Code 11 YES YES Code YES YES Transmit start & stop char, *data length *data length *data length 128/EAN 128 Code 39 YES YES YES For ASCII, Transmit start & stop char, Append mode, *data length Code 93 YES *data length Dutch (KIX) YES Post EAN 13 YES YES 2 digit addenda,
Enable / Symbology Disable Barcode RSS Char Check Transmit / Digit Check Others verification Char/digit YES *data length (Databar) UPC A YES YES 2 digit addenda, 5 digit addenda, Addenda required, Include addenda separator, Send number system UPC E YES YES 2 digit addenda, 5 digit addenda, Addenda required, Include addenda separator, Send number system, Expanded UPC-E UPC E1 YES YES 2 digit addenda, 5 digit addenda, Addenda required, Include addenda separator, Send number system, Expanded
28 Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 5 Advanced Settings Performing a Hardware Reset You may have to perform a reset if the device freezes (i.e., the device no longer responds to the buttons or tapping on the screen). A soft reset allows your device to get a fresh start, similar to rebooting a computer. This will restart your device and adjust memory allocation. All records and entries are retained after a soft reset. Unsaved data in open programs may be lost. Performing a Warm Boot 1. 2. Remove the stylus from its holder.
Method 1: From Windows Mobile 1. Tap Start BootMode. The BootMode Screen appears. 2. Tap Cold Boot. The system is reset and you will lose all data including all files in the RAM memory. Method 2: From Hardware To start the cold boot for the PA690, press and hold the left trigger button and then press the reset button with a stylus. NOTE: When you perform hard reset, the data and time settings will not be retained. Formats, preferences and other settings are restored to their default factory settings.
Appendix I System Specification CPU Memory OS Keypad Marvell PXA320 806MHz Mobile DDR: 256MB NaNDFlash: 512MB Phone version -Windows Embedded Handheld 6.5 professional version Without phone version -Windows Embedded Handheld 6.5 classic version Numeric keypad -- Total 26 keys (including power key) QWERTY keypad -- Total 44 keys (including power Key) Display WVGA, 3.
Environmental Models Regulatory Approvals Software Accessories Dimension Approximately 177.66mm (L) x 40.41mm (H) x 74.58mm (W) (Antenna length included) Operating temperature -10 °C ~ 50 °C Charging temperature 0 °C ~ 40 °C Storage temperature -20 °C ~ 60 °C Relative humidity 5% ~ 95% (non-condensing) Drop test to concrete 1.5 Meter Environmental sealing IP65 BT + WIFI + Camera BT + WIFI + Camera + GPS + 3.5G CE, FCC, VCCI, CCC, NCC Microsoft Visual Studio 2005 Microsoft Windows Mobile 6.
Appendix II Worldwide Support Unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest Unitech regional service representative. For complete contact information please visit the Web sites listed below: Region Web Site Global Operation Center http://www.ute.com Unitech Taiwan http://tw.ute.com Unitech Asia Pacific & Middle East http://apac.ute.com http://india.ute.
