User's Manual

Button map
MUG9700-SDDS-01
URC9700 Manual Bluetooth Pairing Mode Volume Lock To Unlock Volume
(IR assisted pairing)
User Manual
Hold Play/Pause + Digit 0 until
Feedback LED starts blinking
Feedback LED will stop blinking to
confirm pairing
a. If Pairing is unsuccessful, hold
OK/SELECT and MENU until
LED blinks and press digits 9 - 6 - 6
b. Repeat Steps 1 and 2
x2 Blinks
1 2
Audio Device Brand Setup
Turn ON the device that you wish
to setup
Press the OK/SELECT key once,
feedback LED blinks once
1
4
Press and hold OK/SELECT and
Exit until the feedback LED blinks
twice
3
Find your device brand in the
Brand Set / Simple Set table
below.
Note the number that corresponds
to your device brand
2
x2 Blinks
x2 Blinks
x1 Blink
While pointing the remote at the
Audio Device, press and hold the
number key for your brand that
you noted in step 2.
Release the key as soon as the
device turns OFF.
LED will go OFF and will blink
(ON-OFF) during every code
transmitted.
6
Press the Power key on the
remote control to turn your device
back ON.
Done.
If this does not work for your
device, Proceed to Direct Code
Entry steps.
Industry Canada Statement
For Industry Canada Industry Canada Statement
This device complies with RSS-210 of the
Industry Canada Rules. Operation is subject to
the following two conditions: (1) this device
may not cause harmful interference, and (2) this
device must accept any interference received,
including interference that may cause undesired
operation.
Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le
fonctionnement.
7
Press digit key 2.
5
TV Brand Setup
Direct Code Entry for Audio Devices Getting StartedDirect Code Entry for TVs
Turn ON the TV that you wish
to setup
Press the OK/SELECT key once,
feedback LED blinks once
1
4
Press and hold OK/SELECT and
MENU until the feedback LED
blinks twice
3
Find your device brand in the Brand
Set / Simple Set table below.
Note the number that corresponds
to your device brand
2
x2 Blinks
x1 Blink
x2 Blinks
While pointing the remote at the
TV, press and hold the number
key for your brand that you noted
in step 2.
Release the key as soon as the
device turns OFF.
LED will go OFF and will blink
(ON-OFF) during every code
transmitted.
6
Press the Power key on the
remote control to turn your device
back ON.
If this does not work for your
device, Proceed to Direct Code
Entry steps.
7
Press digit key 1.
5
TV Brand Digit
LG 1
Panasonic 2
Philips, Magnavox 3
RCA 4
Samsung 5
Sanyo 6
Sharp 7
Sony 8
Toshiba 9
VIZIO 0
Audio Brand Digit
Bose 1
Denon 2
LG 3
Onkyo 4
Panasonic 5
Philips 6
Pioneer 7
Samsung 8
Sony 9
Yamaha 0
Press and hold OK/SELECT and
MENU until the feedback LED
blinks twice.
1
Press Volume Up key
2
Enter Corresponding Device Digit
to lock Volume to
3
The feedback LED will blink twice
4
Complete
5
Turn ON the TV
Enter the 4 digit device code. The
feedback LED will blink twice to
indicate successful programming
1
5
Refer to Code List for the brand
setup code for the device you would
like to control
(SEE REVERSE SIDE
OF THIS MANUAL)
2
Press and hold OK/SELECT and
Exit until the feedback LED blinks
twice
3
x2 Blinks
Press the Power key on the
remote control
7
If your TV turns off process is
complete, if TV does not turn off
repeat steps 2 - 7 using the next
code in the Chart
8
Press digit key 1.
4
x2 Blinks
Turn ON the Audio Device
Enter the 4 digit device code. The
feedback LED will blink twice to
indicate successful programming
1
5
Refer to Code List for the brand
setup code for the device you would
like to control
(SEE REVERSE SIDE
OF THIS MANUAL)
2
Press and hold OK/SELECT and
MENU until the feedback LED
blinks twice
3
x2 Blinks
Press the Power key on the
remote control
7
If your Audio Device turns off
process is complete, if TV does
not turn off repeat steps 2 - 7
using the next code in the Chart
8
Press digit key 2.
4
Device Digit
STB 0
TV 1
Audio 2
x4 Blinks
x2 Blinks
Press and hold OK/SELECT and
MENU until the feedback LED
blinks twice.
1
Press Volume Up key
2
The feedback LED will display four
blinks to indicate that the volume
has now been unlocked
3
Complete
4
TV:
Powers ON and
Off your TV
INFO:
Displays info for
currently
selected program
VOLUME:
Controls and
mutes TV volume
STB:
Powers ON and
OFF your Set Top
Box
APPS:
Takes you to your
OTT/Apps
homescreen
LAST:
Returns to last
channel you were
watching
TRANSPORT:
Controls DVR
Programming
SEARCH:
Activates Voice
Search
Functionality using
Microphone at top
of Remote
MENU:
Displays main
cable menu
GUIDE:
Displays
program guide
EXIT:
Exits current
menu and
returns to
current program
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate
radio
frequency energy and if not used in accordance
with the instructions, may cause harmful
interference
to radio communications.
However, there is no guarantee that interfer ence
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, the user is
encouraged or
try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase or decrease the separation between
the equipment and receiver.
• Connect the equipment into an outlet on a
circuit di�erent from that to which the receiver is
connected
• Consult the dealer or an experienced remote
control/ TV technician for help.
• It is strongly recommended that the TV be
plugged into a seperate wall outlet.
This equipment has been veri�ed to comply with
the limits for a Class B computing device,
pursuant to
FCC Rules. The user is cautioned that changes
and modi�cations made to the equipment
without the
FCC Statement