Atlas OCAP M1056L.
Atlas OCAP M1056L.fm Page 2 Friday, December 22, 2006 6:10 PM TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Key Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Device Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Installing Batteries . . . . . . . . . . . . .
Atlas OCAP M1056L.fm Page 3 Friday, December 22, 2006 6:10 PM Setup Codes for DVR/PVR Systems . . . . . . . . . . . . . . . . . . . . 43 Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Setup Codes for TVs (DLP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Setup Codes for TVs (HDTV) . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Setup Codes for TVs (LCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Setup Codes for TVs (Plasma) . . . . .
Atlas OCAP M1056L.fm Page 4 Friday, December 22, 2006 6:10 PM INTRODUCTION The Atlas OCAP 5-Device Remote Control with Learning by Universal Electronics is our latest generation universal remote control. Its sophisticated technology allows you to consolidate up to five of your original home entertainment remote controls into one easy-touse product.
Atlas OCAP M1056L.fm Page 5 Friday, December 22, 2006 6:10 PM FEATURES AND FUNCTIONS Use the illustration below to locate features on the Atlas OCAP 5-Device Remote Control with Learning and then study the Key Charts (on the next three pages) to learn how they function. To find out what type of devices can be controlled by each device key after programming, see “Device Table” on page 8 . www.urcsupport.
Atlas OCAP M1056L.fm Page 6 Friday, December 22, 2006 6:10 PM Key Charts Key Function Use SETUP for all programming sequences. Also use to turn backlighting on and off, if applicable. Press PWR once to turn on or off a home entertainment device. For MASTER POWER control, see “Using the Master Power Key” on page 22. Press VCR, DVD, AUD, TV, or CBL once to select a home entertainment device to control. Also see “Device Table” on page 8.
Atlas OCAP M1056L.fm Page 7 Friday, December 22, 2006 6:10 PM Key Function Use VOL+ (or VOL-) to raise (or lower) the audio volume. Use FAV to cycle through your favorite channels stored in your cable converter. Use CH+ (or CH-) to select the next higher (or lower) channel. For DVD players, use these keys to skip forward (or reverse) through chapters. For amplifiers/receivers, use these keys to select the next higher (or lower) preset station. Press MUTE once to turn the sound off or on.
Atlas OCAP M1056L.fm Page 8 Friday, December 22, 2006 6:10 PM Key Function Press ASPECT once to change the aspect ratio of the show you are watching. (Not available on all set-top boxes). Press SHIFT to access additional cable features (see your cable converter’s manual). Use PIP ON-OFF to switch the PictureIn-Picture feature on or off (if available on your TV or cable service). Use PIP SWAP to switch images and sound between the main and window pictures (if available on your TV or cable service).
Atlas OCAP M1056L.fm Page 9 Friday, December 22, 2006 6:10 PM Device Key Controls these types of devices Television Cable Box (Converter) or Satellite Receiver INSTALLING BATTERIES ❶ ❷ ❸ 1. 2. 3. 4. NOTE: On the back of the remote control, push the tab and lift off the battery cover. Locate the two (2) enclosed AA batteries. Match the + and - marks with those in the battery case, then insert them. Align the covers keys with the cases holes and press the cover back into place.
Atlas OCAP M1056L.fm Page 10 Friday, December 22, 2006 6:10 PM PROGRAMMING DEVICE CONTROL The Atlas OCAP 5-Device Remote Control with Learning is preprogrammed to operate the cable box (converter) provided by your cable system, an RCA TV, a Toshiba DVD player, an RCA VCR, and a Pioneer audio receiver. To control devices other than the default brands, perform the following steps; otherwise skip this section.
Atlas OCAP M1056L.fm Page 11 Friday, December 22, 2006 6:10 PM 5. Repeat steps 1 through 4 for each device you want the remote control to operate. For future reference, write down each working device code in the boxes on the following page.
Atlas OCAP M1056L.fm Page 12 Friday, December 22, 2006 6:10 PM NOTE: (for example, TV/VCR). If you perform this procedure correctly, the VCR key will blink twice. If the VCR key did not blink twice after entering the codes last digit, repeat steps 2 through 3 and try entering the same code again.
Atlas OCAP M1056L.fm Page 13 Friday, December 22, 2006 6:10 PM 3. Enter 9 9 1. The TV key will blink twice. 4. Aim the remote control at the TV and press PWR once. 5. Press and release the CH+ key continuously, then stop when the TV turns off. NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. Press PWR. The TV should turn on, then press SETUP to lock in the code. 6.
Atlas OCAP M1056L.fm Page 14 Friday, December 22, 2006 6:10 PM CHECKING THE CODES If you have set up the Atlas OCAP 5-Device Remote Control with Learning by searching for your device code (on the previous page), you may need to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV: 1. On the remote control, press TV once; it will blink once. Then press and hold SETUP until the TV key blinks twice. 2. Enter 9 9 0. The TV key will blink twice.
Atlas OCAP M1056L.fm Page 15 Friday, December 22, 2006 6:10 PM • Learning capacity is approximately 16 to 25 keys, depending on the code being learned. • Certain device functions are not learnable including multi-frequency types, some high frequency ones, and other unusual formats. • For optimum learning, avoid high levels of ambient light such as natural sunlight or energy-efficient fluorescent lights. NOTE: Please have your original remote controls handy before programming learning.
Atlas OCAP M1056L.fm Page 16 Friday, December 22, 2006 6:10 PM NOTE: 6. the key on the original remote until the Atlas OCAP 5-Device Remote Control with Learning’s LED blinks twice. If the LED displays one long blink, a learning error has occurred. Try repeating this step again until a successful capture occurs. If the function is still not captured, press and hold SETUP to exit programming and review the “Learning Precautions” on the previous page. If needed, also see “Troubleshooting” on page 25.
Atlas OCAP M1056L.fm Page 17 Friday, December 22, 2006 6:10 PM Deleting All Learned Keys in a Specific Mode NOTE: If more than 15 seconds pass between key presses, the remote exits programming. 1. Press and hold SETUP until the last-selected mode key blinks twice, then press 9 7 5. 2. 3. Press a mode key twice (i.e., VCR, DVD, AUD, TV, or CBL) to clear all the learned keys for that mode. The LED blinks twice. Repeat step 2 for another mode or press and hold SETUP to exit programming.
Atlas OCAP M1056L.fm Page 18 Friday, December 22, 2006 6:10 PM Locking Channel Control to CBL 1. On the remote control, press CBL once; it will blink once. Press and hold SETUP until the CBL key blinks twice. 2. Enter 9 7 3.The CBL key will blink twice. 3. Press CH+ once. The CBL key will blink twice. Now, regardless of what mode you select (except AUD), the channel keys will only change channels on your cable converter.
Atlas OCAP M1056L.fm Page 19 Friday, December 22, 2006 6:10 PM 3. Press VOL- once. The last-selected device key will blink four times. 4. Repeat steps 1 through 3 for each device you want volume to be unlocked. Now, after you select a device that has volume unlocked (e.g., CBL), pressing VOL+, VOL-,or MUTE, will control only that device’s volume. Unlocking All Volume Control (Global Volume Unlock) NOTE: Performing these instructions will set independent volume control for all programmed devices. 1.
Atlas OCAP M1056L.fm Page 20 Friday, December 22, 2006 6:10 PM PROGRAMMING CABLE ID LOCK The Atlas OCAP 5-Device Remote Control with Learning is locked at the factory to operate your cable provider’s set top box. However, if you have another brand or model of cable converter or satellite service that you would like to control, then you’ll need to perform the following steps to unlock the ID Lock, enter a new manufacturer’s code, and lock the ID Lock again. 1. Turn on the cable converter. 2.
Atlas OCAP M1056L.fm Page 21 Friday, December 22, 2006 6:10 PM Programming a Macro Key 1. On the remote control, press and hold SETUP until it blinks twice. 2. Enter 9 9 5. The SETUP key blinks twice. 3. Select a macro key (for example, F1) and press it once. Press the key sequence you want to program into the macro. For example, to turn on your TV and raise its volume, press TV followed by VOL+. 4. NOTE: 5. 6. NOTE: You can program up to 15 key presses into one macro.
Atlas OCAP M1056L.fm Page 22 Friday, December 22, 2006 6:10 PM USING THE MASTER POWER KEY The Atlas OCAP 5-Device Remote Control with Learning has a unique feature that allows you to sequentially turn up to five of your home entertainment devices on or off with a single key press. NOTE: MASTER POWER (PWR) only works in the CBL mode. If it is not programmed, only the cable converter will turn on or off. In any other mode, pressing MASTER POWER (PWR) once will turn the selected device on or off.
Atlas OCAP M1056L.fm Page 23 Friday, December 22, 2006 6:10 PM Using the Master Power Key 1. After programming, point the remote control at the devices. Press CBL once. 2. Press PWR once to sequentially turn the programmed home entertainment devices on or off. You will see the devices turn on or off according to the programmed sequence. Clearing the Master Power Key 1. On the remote control, press and hold SETUP until the last-selected device key blinks twice. 2. Enter 9 9 5.
Atlas OCAP M1056L.fm Page 24 Friday, December 22, 2006 6:10 PM 3. Press AUD once, then press VCR once. The VCR key will blink twice. The VCR key is now ready to be programmed for your second audio device. See “Programming Device Control” on page 10. To re-assign other device keys, repeat these and substitute the key sequence using the following chart: NOTE: Only one device can be assigned to an unused device key at a time.
Atlas OCAP M1056L.fm Page 25 Friday, December 22, 2006 6:10 PM 2. Enter 9 8 0. The last-selected device key blinks twice, pauses, and blinks twice again to confirm that all custom programming is cleared. ACTIVATING BACKLIGHTING (OPTIONAL) On some models of your Atlas OCAP 5-Device Remote Control with Learning, you can activate backlighting. Backlighting enables your remote’s keypad to remain lit for five seconds after you press any key.
Atlas OCAP M1056L.fm Page 26 Friday, December 22, 2006 6:10 PM PROBLEM: PLAY and STOP keys do not work on a Motorola DCT-2000 cable converter. SOLUTION: Re-program the CBL key for cable code 0476 (see “Programming Device Control” on page 10). PROBLEM: Tried Search Method and still could not find a working code. SOLUTION: Try the Search Method again after clearing out the device key as follows: a. Press and hold SETUP until device key blinks twice. b. Enter 9 9 2. c.
Atlas OCAP M1056L.fm Page 27 Friday, December 22, 2006 6:10 PM radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment. ADDITIONAL INFORMATION This product does not have any user-serviceable parts. Opening the case, except for the battery cover, may cause permanent damage to your Atlas OCAP 5-Device Remote Control with Learning.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.fm Page 39 Friday, December 22, 2006 6:10 PM Venturer Vialta Vizio Vocopro Xbox Xwave Yamaha Yamakawa Zenith Zoece 0790 1509 1064, 1226 1027 0522, 1708 1001 0490, 0539, 0545 0872 0503, 0591, 0741, 0869 1265 www.urcsupport.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.fm Page 56 Friday, December 22, 2006 6:10 PM Hitachi iLo Initial Jensen KLH Konka LG Magnavox Mintek Panasonic Philips Polaroid Prima RCA Samsung Sansui Sova Sylvania Toshiba 1247 1472 1472 1016 1261 0719, 0720 1526 1268 1472 1490 0854, 1260 1480 1016 1022, 1193 0899 0695 1122 0675, 1268 0695 www.urcsupport.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.
Atlas OCAP M1056L.fm Page 66 Friday, December 22, 2006 6:10 PM NOTES www.urcsupport.
Atlas OCAP M1056L.fm Page 67 Friday, December 22, 2006 6:10 PM NOTES www.urcsupport.
Atlas OCAP M1056L.fm Page 68 Friday, December 22, 2006 6:10 PM M1056L Revision 1.