User's Manual

CO2ZB1ZigbeeCO2Sensor 
InstallationInstructionsandUserManual

1. Specifications
Frequency:   2.4GHz(IEEE802.15.4)
OperatingTemperature: 14°‐122°F(‐10°‐50°C)
OperatingHumidity: 10%‐90%non‐condensing
CO2SensingRange:  400ppm–5000ppm
CO2SensingAccuracy: ±75ppm+5%MV
Battery:   4xAAAlkalineBattery
BatteryLife:  2Years(withdefaultsetting)
Compatibility:   Zigbee,
WWAH(WorkswithAllHubs)


2. PackageContents
1xSensor
2xScrews&WallAnchor
4xAAAlkalineBattery(uninstalled )
2xBackMounting2‐SidedAdhesiveTape
1xManual


3. ComponentIdentification



4. ZigbeeEnrollment:
ThisCO2Sensorneedstobepairedbeforeinstallation.
1. Insert4batteriestothebatterycompartment
2. TheLEDwillblinkthreetimesinambercolorevery2‐3secondswhile
scanningthenetwork.
3. Ifnetworksuccessfullyjoined,theLEDwillbelitfor1secondinambercolor

followedbyashortblinkingreencolor.
4. Ifnetworkisnotfoundafter1minute,thesensorwillgointosleepmode,
theLEDwillblinkinambercolorevery1minute.Youneedtoresetthe
sensortotriggerapairingprocess,andthensensorwillrepeat
stepsfrom2
to4.

Toresetthesensor:
1. Removethebatteryfor10seconds
2. Pressandholddownthetamperswitchwhilere‐insertthebattery
3. Releasethetemperswitchwithin3secondsafterinsertthebattery

Note:MACaddressoftheSensorcanbefound
ontheQRcodebyscanningit 
withyourmobilephone.


5. Mounting 
MountingbyScrew
 Pressthecasereleasebuttontoseparatethefrontandwallanchorcase.
 Thebackcasegivesaccesstoboththeflushmou ntandcorn ermount
screwknockouts.Drillthroughtheappropriateknockoutsandusethe
includedscrewstomountinthedesiredmounting
location.
 Itisrecommendedtoensurethereisatightsealaroundtheknockoutsto
preventbugsfromenteringthesensorandcausingfalsealarms.
 Replacethefrontsensorcovertosnapshutandscrewinthesensorcase
screwsonthetopandbottomofthewallanchor
case.








MountingbyAdhesiveTap
 Pressthecasereleasebuttontoseparatethefrontsensorcaseandwall
anchor.
 Insertthebatteryintothebatterycomp artment.
 Putbackthewallanchorcasewithfrontsensorcase.
 Placeonesideadhesivetapeoverthe
wallanchorcase,thesidethatwill
facethewall.
 Peelofftheothersideofadhesivetape.
 Placethesensoronthewall.





6. Operation 

TheCO2sensorrequires45secondstowarmupforsignalstabilizingwhen
performingstartuporreset.Duringthewarmupperiod,theLEDwillblinkslowly
inamber.Duringnormaloperation,theLEDwillblinkevery5minutesingreen
colortoindicatethesensorisworkingproperly.However,there
arenoLED
indicationswhenmotionisdetected.Thisisdonetomaximizebatterylife.
Furthermore,whenmotionisdetectedandasignalistransmittedtothepanel,
thesensorwillnottransmitagainforaperiodofthreeminutes.







