Datasheet

181818
Vehicle
Car alarm simulation with on/off
switch.
contents: flashing LED 12Vdc and
2 stickers
K/NEP
Detects objects using ultrasonic waves
When the preset minimum distance is crossed, an audible signal is generated
detection range: 5cm - 1.5m (adjustable)
• detection angle: 5°
• supply voltage: 10 - 15VDC / 16mA
• PCB dimensions:
• sensor: 28 x 95mm / 1.1 x 3.7”
• base: 48 x 125mm / 1.9 x 4.9”
K3502
For cars or motorcycles with a petrol engine.
• May be used as a general purpose revolution counter.
• range: 100 - 9900 revolutions/minute
• 2 digit display
• easy calibration
• power supply: 10 - 15VDC / 200mA
• PCB dimensions:
• PCB 1: 80 x 45mm / 3.2 x 1.8”
• PCB 2: 80 x 60mm / 3.2 x 2.4”
• front panel dimensions: 70 x 90mm / 2.8 x 3.5”
K2625
The alarm detects sudden voltage drops of the battery when the
interior, trunk, or hood lights are switched on.
• To ensure correct operation, a number of control indications
have been included, such as : flashing LED to indicate that
the alarm is in standby mode after a set time (after you have
left the car).
• Pre-alarm (built-in buzzer) to indicate that the alarm is
activated, so that you will not forget to switch it off.
• The alarm is easy to switch on and off, either automatically or
by means of the ignition switch or a remote control unit, such
as the K8059/K8057 or MK161/MK162
• detects voltage drops of the battery
• entry delay time: 2 to 30 seconds with buzzer indication
• exit delay time: 2 to 180 seconds with LED indication
• alarm period: 60 seconds with automatic reset
• power supply: 12V
• standby current: 25mA
• relay output: 5A
• PCB dimensions: 62 x 100mm / 2.4 x 3.9”
K3504
Up to 3 different time intervals (2 - 10 - 15 seconds) can
be selected for the windshield wipers of your car.
• It can also be used for automatic slide projection.
• relays on PCB: 2 inverters
• power supply: 12 - 15VDC
• PCB dimensions: 82 x 56mm / 3.2 x 2.2”
K2599
Gives your car the feel of an expensive luxury car.
• Better starting and smoother running, particularly
at very high and very low RPM.
• Lower fuel consumption, less pollution, lower
servicing costs.
• Drive economically, drive electronically.
• Only for petrol/gasoline engines.
• Only for cars with negative ground.
• Tested on 2, 4, 6 and 8 cylinder cars
• max. current: 4A
• connection speed: up to 500kHz
• PCB dimensions: 70 x 35mm / 2.8 x 1.4”
K2543
If, like most of us, you do not have infrared
eyesight, then at times you have probably found
yourself fumbling for the ignition switch or seat belt
in the dark.
• For people like you we have developed this
solution.
• With extra push button and battery protection.
• switch-off delay: adjustable for 0 to 60 seconds
• power supply: 12-15Vdc
• power consumption: 13mA
• PCB dimensions: 45 x 70mm (1.8” x 2.8”)
K3500
This head light indicator may be set for one or two functions.
• To indicate that the headlights (or the sidelights) should be switched off
after switching off the ignition contact (battery protection).
• Or to indicate that the head lights should be on once ignition contact is
switched on (obligatory in some countries).
• continuously repeated alarm tone for lights ON (may be disabled)
• repeated alarm tone for lights OUT
• only 3 wires are required for hook-up
• supply voltage: 12V battery
• PCB dimensions: 48 x 57mm / 1.9 x 2.2”
K3505
Drive more safely in freezing weather.
• This kit uses a flashing LED to indicate a
road temperature close to freezing point ;
below that point the LED is on continuously.
• A reliable temperature sensor with
mounting stud is included.
• power supply: 10 - 15VDC / 25mA
• PCB dimensions: 56 x 42mm / 2.2 x 1.7”
K2644
K3505
Car light warning alarm
K3504
Car alarm
K3502
Ultrasone radar
K3500
Multifunction car courtesy light
K2599
Windshield wiper robot or interval
timer
K2625
Digital tachometer
K/NEP
Imitation car alarm
K25 43
Electronic transistor ignition for cars
K2644
Frost indicator