Datasheet

21 21
VM101: p36
This kit allows you to control a lamp or group of lamps through a DMX
signal.
• The DMX protocol was developed by USITT in 1986 with the
purpose of controlling dimmers, scanners, moving heads and
other lighting devices with simple wiring.
• It is mainly being used in theatres and discos, but you can
use it in any place where a central or automated lighting is
needed.
• Use our “USB controlled DMX interface” K8062 (kit version),
VM116 (built version) or any other control console compliant
with the DMX-512 protocol as a controller
• suitable for resistive loads like incandescent lamps and mains
voltage halogen lighting. system addressability: 512 unique
addresses, selectable with DIP switch. status LED for power
and error detection. toroidal filtering for low noise (according
to EN55015). stand alone “test” mode. control source: DMX-
512, 3 pin XLR socket included
• load capacity: max. 1000 W @ 230V (5A) or 500W @ 115V
• power Input: 115/230 VAC
• size: 150 x 60 x 45mm / 5.9 x 2.36 x 1.8”
powerful high-quality dimmer, suitable for incandescent lamps, mains
voltage halogen lighting and low voltage halogen lighting in combination
with a conventional (wire wound) transformer. easy push-button operation
for dimming of light sources.. phase control can be disabled. non-volatile
memory for last set light intensity. lots of safety features to make lamps
last as long as possible, such as “oftstart” and automatic turn-off after
12h or after 20min at too low intensity. transformer protection in case of
defective light sources. LED status indication
suppression of radio & TV interference according to EN55015
• operating voltages: 110-125V or 220-240V AC (50/60Hz)
• max. load: 1000W/230V or 500W/115V (5A)
• max. phase shift with inductive load: 30°
• dimming speed: ± 5 sec.
• PCB dimensions: 90 x 75 x 40mm
• ambient temperature: 10°C to 40°C
With this device wires can be very easily checked for
mains voltage. It can be used to search for wires installed
in or behind walls or to trace interruptions in wiring.
A flashing LED indicates whether or not voltage is present.
• The flashing speed indicates how close by the wire is.
• If an audible signal is also desired, space has been
provided on the PCB for buzzer SV4/12-S to be
connected.
• The PCB has been specially constructed to fit entirely
into the separately available box type G407.
• detection of mains conducting cables
• LED indication (buzzer optional)
• adjustable detection distance: max. 10cm, 3.9”
• distance indication
• supply voltage: 9V battery (not incl.)
• dimensions: 56 x 64mm / 2.2 x 2.5”
Home
K8039
K8064
Geschikt voor het aansturen van gloeilampen, halogeenverlichting
op netspanning of laagspanningshalogeenverlichting in combina-
tie met een conventionele transformator.
• simple brightness adjustment by means of a DC voltage. optically
isolated adjustment input. pre-set adjustment for full brightness. suitable
for incandescent lamps, mains voltage halogen lighting and low voltage
halogen lighting in combination with a conventional transformer. “Soft
start” feature to ensure lamp longevity. transformer protection in case
of defective light sources. LED status indication. compatible with our
computer interface cards: K8000, K8055
• adjustment voltage: 0 to 12Vdc max.
• max. adjustment current: 2.25mA at adjustment voltage of 12V
• suppression of radio & TV interference according to EN55015
• operating voltage:
• 110-125V or 230-240V AC (50/60Hz)
• max. load: 750W/230V or 375W/110V, 0-98% adjustable
• max. phase shift with inductive load: 30°
• PCB dimensions: 90 x 75 x 40mm / 3.5 x 3 x 1.6”
K8038
K8026
Due to its small size, this small dimmer easily replaces an existing
switch, permitting you to vary the brightness of a light or group of
lights.
• The dimmer may also be used to adjust the speed of a
motor, vacuum cleaner, or any other motor with carbon
brushes.
• A mains suppresser is provided eliminating undesirable
RFI.
• It is not suitable for halogen lamps.
• protected against induction voltage peaks
• load: 3.5A (750W at 230V and 380W at 110V)
• suppressed according to EN55015
• PCB dimensions: 60 x 60mm / 2.4 x 2.4”
K8028
microcontroller technology. 13 different functions: impulse switch, staircase
light control, slow ON/OFF dimmer, interval timer, speed adjustment for
fans, etc…. suitable for both resistive and inductive loads (light bulbs, high-
voltage halogen lighting and low-voltage halogen lighting with ferromagnetic
transformer). “Soft Start” prolongs the life of the bulbs. an advanced security
system with fault indication automatically deactivates the mounted if the load
or no-load behaves too inductively. can be operated from several locations,
simply by the parallel connection of push buttons. 2 delay times (anywhere
between 5 sec. to 2 hours each) can be programmed through the learning
mode. memory is protected against power failures. equipped with fuse and
key for function selection. equipped with a mains suppressor according to
EN55015 norms
supply voltage: 110-125V or 220-240Vac, 50 or 60Hz
• automatic detection of mains frequency: 50 or 60Hz
• max. load: 2.5A (300W / 120V - 600W / 230V)
• dimensions: 100 x 82 x 36mm / 3.9 x 3.2 x 1.4”
K6712
This one channel IR receiver/dimmer works together with the 15
channel IR transmitter (K6710 & K8049).
• The receiver code can be set to 1 of the 15 transmitter
codes so that 15 receivers can be operated (K6712
and/or K6713) independently of each other.
• Thanks to its compact design this kit fits into a standard
light switch housing.
• max. load: 2A (4A with heat sink)
• supply voltage: 220VAC 50/60Hz (110VAC possible)
• transmitter / receiver distance: max. 7m (23’)
• not suitable for halogen lights
*Beschikbaar zolang de voorraad strekt
mounted version
K7101
K7102
To come up against an electric cable
while drilling a hole in a wall can have
catastrophic consequences.
• Likewise, drilling into gas, water pipes or central
heating pipes can be extremely hazardous.
• With a handy metal detector it can now be determined
beforehand whether there are metal objects to be found
in a wall, ceiling or floor.
• An LED indicates if a metal object is in the vicinity.
• avoid disasters when drilling holes in walls. locate
pipes, cables, metal studs, …. great project for
novices. your own unique application. push button
operation
• metal detecting distance adjustable: up to 8cm (3.15”)
• power supply: 9V battery (not incl.)
• LED indication
• 12VDC-buzzer connection (buzzer not included)
• dimensions: 56 x 64mm (2.2” x 2.5”)
K6600
This device is a simple and economic way of generating
electronic tones.
• This kit is primarily intended for use as a replacement for
the traditional mechanical doorbell.
• Of course, it can also be used for many other types of
applications.
• The number of tones may be selected up to a maximum
of three, each of which is output one after the other.
• This can be used to help locate the place being called.
• Volume and tone can also be set.
• The existing bell transformer can be used as a power
supply.
• adjustable tone and volume control
• 1, 2 or 3 tones selectable
• loudspeaker output: 0.3W / 8ohm
• power supply: 6 to 9VAC / 0.2A or 4.5V battery (3 x 1.5V
AA batteries (not incl.)
• idle current: less than 10µA
• dimensions: 53 x 59mm / 2.1 x 2.3”
K6600
Multitone chime
K7102
Metal detector
K8026
3.5a dimmer with potentiometer
K7101
Mains voltage detector
K8039
1 channel dmx controlled power dimmer
K6712
IR remote controlled dimmer
K8028
Multifunctional dimmer
K8038
Power dimmer, push-button controlled • 1kw@230v
K8064
Dc controlled dimmer