owners manual Range Hood ULT2820, ULT2824, ULT2830, ULT2836

ManualsBrandsUniversal Metal Industries ManualsVentilation HoodULT2836

INSTALLATION INSTRUCTIONS &

USE & CARE GUIDE

Trade-Wind

Ultra Series Range Hoods

410 CFM

Ultra Series Models:

ULT2820

ULT2824

ULT2830

ULT2836

CONTENTS:

Part 1 - Planning The

Installation

Part 2 - Electrical Connection

Part 3 - Direction of Vent and

Securing The Hood

Part 4 - Use & Care

READ AND SAVE THESE INSTRUCTIONS

Before beginning installation, please thoroughly read and become familiar with these instructions. Installation and

service must be completed by a qualified installer. Failure to properly install this product may void the warranty.

Installer:

Please leave these installation instructions with the range hood.

Owner:

Please keep these installation instructions for local electrical inspector’s use and for future reference.

WARNINGS: Must be followed carefully to avoid personal injury

IMPORTANT: Must be followed carefully to avoid damage

TIPS: Contain helpful information

WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the

manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag to the service panel.

3. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction.

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS & USE & CARE GUIDE Trade-Wind® Ultra Series Range Hoods 410 CFM Ultra Series Models: ULT2820 ULT2824 ULT2830 ULT2836 CONTENTS: Part 1 - Planning The Installation Part 2 - Electrical Connection Part 3 - Direction of Vent and Securing The Hood Part 4 - Use & Care READ AND SAVE THESE INSTRUCTIONS Before beginning installation, please thoroughly read and become familiar with these instructions. Installation and service must be completed by a qualified installer.
PAGE 2
WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 4. Sufficient air is needed for proper combustion and exhausting of gasses through the flue (chimney) or fuel burning equipment to prevent back drafting.
PAGE 3
6. The ducting must be air tight. Use a minimum of 2 sheet metal screws at every duct joint. Then, seal the duct joints with high quality duct tape. 7. Only use ductwork constructed of materials deemed acceptable by state, municipal and local codes. 8. Plan the installation so that all minimum clearances are met or exceeded. Dimensions shown provide minimum clearances, unless otherwise specified.
PAGE 4
PART 2 Electrical Connection WARNING! Ensure that the power supply is disconnected before proceeding. Verify that the power supply matches the ratings found on the appliance data label before proceeding. The complete appliance must be properly grounded at all times when electrical power is applied. Do not ground the appliance with the neutral (white) house supply wire. A separate ground wire must be utilized.
PAGE 5
PART 3 Determining Direction of Vent and Securing the Hood MOUNTING HOLES: Because the Trade-Wind® Ultra Series rangehood was designed for all applications, no mounting holes have been pre-drilled. This allows the hood (or liner) to be attached in the areas of the cabinet or wood hood canopy that have proper wood frame support. The hood should be attached to the wood framing through the top. Remove the filters. Mark and drill screw holes through the hood as required.
PAGE 6
PART 4 Use and Care OPERATING CONTROLS: Always activate the ventilator when using cooking appliances. Activate the ventilator a few minutes before starting to cook to establish an airflow pattern within the room. Adjust the fan speed as needed. Adjust the dimmable halogen lights as desired. Eliminate air currents in the hood vicinity by shutting nearby windows and doors, turning off ceiling fans and adjusting the adjacent heating and air conditioning outlets if necessary.