Operating Your System With the MX-810 ™ COMPLETE CONTROL Universal Remote Control®
This remote control was Custom Programmed for you by: For questions about your Custom Programming call: Custom Programming of a complex home theater and/or a multi-room system is one of the most challenging tasks within an audio/video installation. It involves an intimate knowledge of how the components interact and exact details on the proper sequences of control.
TABLE OF CONTENTS Introduction to the MX-810 1 Optional RF “No Rules” Operation 2 Installing and Charging the Battery 3 Programming the MX-810 4 Using the MX-810 to Manually Control a “Device” 5 Using the MX-810 to Automate an “Activity” 6 Using the Help System for Automated Activities 7 Accessing the MX-810’s Setup Menus 7 Selecting from the Setup Menus 8 Setting the Color Screen 8 Setting the Button Lighting 9 System Menu 10 Setting the Button Beep Volume 11 Date and Time Menus
MX-810 OWNERS MANUAL Congratulations! You’ve purchased a unique synthesis of hardware and software engineering, the Complete Control MX-810. The MX-810 achieves a magnificent combination of power and flexibility, simplifying and automating operation of even the most complex system. User Configurable Screen and Button Lighting A built in pick up sensor can be set to light the screen and/or the buttons automatically.
MX-810 OWNERS MANUAL Optional RF “No Rules” Operation In combination with a Complete Control RF Base Station, the MX-810 can control your system without being in line-of-sight of the equipment. Either the MRF-350 or the MRF-40 RF base station is compatible with the MX-810. Both incorporate RF Addressing. RF Addressing gives you the ability to control equipment locations throughout your home, even if they are concealed in other rooms or are behind closed doors. 1.
MX-810 OWNERS MANUAL Installing and Charging the Battery Open the battery cover by pressing on the release clip and removing the cover. Note that the three contacts on the battery must connect to the three spring-loaded contacts in the MX810. Angle the battery into the battery compartment, contacts first, then gently fit the rear of the battery into the compartment as well. Replace the battery cover by inserting the hinged end in first, then snapping the cover back into place.
MX-810 OWNERS MANUAL Programming the MX-810 The MX-810 is programmed via a Windows PC equipped with a USB port (programming cable included), using our proprietary software, MX-810 Setup. You can download this software from our website: www.universalremote.com Basic setup takes only a few minutes with this software. However, to fully automate an audio/video system the programmer must have a detailed knowledge of each component and how the system is connected and operated.
MX-810 OWNERS MANUAL Using the MX-810 to Manually Control a “Device” Press the MX-810’s DEVICES button to display all the devices you can control with your MX810. Your MX-810 can control up to 24 devices. If you have more than six devices, press either of the page buttons to display the other devices in your system. When you find the device you want to control, press the corresponding button beside the screen.
MX-810 OWNERS MANUAL Using the MX-810 to Automate an “Activity” You select Activities in the same way that you select Devices. Simply press the MX-810’s ACTIVITIES button to display all the Activities you can automate with your MX-810. However, when you select an activity, the MX-810 is going to automatically reconfigure your entire Audio Video system. 1. The TV turns ON. 2. The Audio system turns ON. 3. The DVD player turns ON. 4. The TV changes to the DVD input. 5.
MX-810 OWNERS MANUAL Using the Help System for Automated Activities After selecting an activity, if any of the devices or components don’t seem to be on or are set incorrectly, use the Help button. There may be several help screens to help you with your activity as shown here: Once the help screens appear, look at your system. If anything is off, use the buttons on the first screen to power them on, then press NEXT (the PAGE button). The second and third screens enable you to correct an input.
MX-810 OWNERS MANUAL Selecting from the Setup Menus There are two pages of settings on the Setup Menu. Use the page buttons to view them. To select, simply press the corresponding button. Select the setting you’d like to adjust by pressing the button beside the screen. Use the Page button to see other pages. Exit the Setup Menus by pressing the Activities or Devices button, or simply waiting (the setup menus time out in 30 seconds).
MX-810 OWNERS MANUAL Setting the Screen Pick Up Sensor Use the buttons next to YES and NO. If you say YES, the color screen will light as long as you are moving the MX-810. If you say NO, the screen will light when you press any button. Use the YES and NO buttons to set the Pick Up sensor. Press the SAVE button to save your setting.
MX-810 OWNERS MANUAL Setting Button Lighting Automatic On Use the buttons next to YES and NO. If you say YES, the buttons will light whenever the LCD screen is on. If you say NO, the buttons will only light when you press the LIGHT button. Use the YES and NO buttons to set the button back lighting to automatically turn on or not. Press the SAVE button to save your setting.
MX-810 OWNERS MANUAL Power Remaining and Battery Warning Settings On this screen, you can see how much battery charge remains and you can reset the “Low Battery” warning to either 10, 20 or 30 percent. The battery indicator at the top left of the MX-810 screen will flash when your low battery warning level is reached. Note the current remaining battery charge here. Use the LESS and MORE buttons to set the battery warning. Press the SAVE button to save your setting.
MX-810 OWNERS MANUAL Date and Time Menus Via the three menus for Date and Time you can set the date, set the time and opt to display either the date or the time. Setting Time Tap the button beside hour or minutes then use the number keys to enter the correct time. Set the AM/PM by toggling the button. When the time is correct, press the SAVE button. Select the field you’d like to change, then use the Number buttons on the MX-810 to enter hours or minutes. Press this button to change AM to PM or PM to AM.
MX-810 OWNERS MANUAL Erasing and Resetting You can erase your MX-810 (all of your work, all devices, all activities will be lost) and reset it to the factory default configuration. Use the CANCEL button to exit without erasing. Press the ERASE button to erase all your work. USA Limited Warranty Statement Your Universal Remote Control, when delivered to you in new condition, is warranted against defects in materials or workmanship as follows: UNIVERSAL REMOTE CONTROL, INC.
MX-810 OWNERS MANUAL applied serial number has been altered or removed from the product. This Limited Warranty is valid only in the United States of America. This Limited Warranty specifically excludes products sold by unauthorized resellers. UNIVERSAL REMOTE CONTROL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR CONDITION ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, THERE IS NO OTHER WARRANTY EXPRESSED OR IMPLIED.
MX-810 SETUP NOTES Your Devices List any component or device you’d like to control with your MX-810: Type of Device (TV, DVD, VCR etc.
MX-810 SETUP NOTES Your Activities Describe the inputs you must set to watch or listen to TV, DVD, CD, Radio etc. in your home entertainment system. Activity (Watch TV, Watch DVD etc.
™ COMPLETE CONTROL Universal Remote Control® 500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 www.universalremote.
