Owner's Manual TKP-7000 Network Keypad
TKP-7000 Owner's Manual ©2012-2013 Universal Remote Control, Inc. The information in this owner’s manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this owner’s manual may be subject to change without prior notice.
TABLE OF CONTENTS Introducing the TKP-7000 1 Installing the TKP-7000 3 Installation 4 Main Menu Navigation 5 Rooms Menu 12 Time & Weather Module 16 Shortcuts Pop-Up 17 Adjusting User Settings on the TKP-7000 19 Rebooting Your TKP-7000 28 Specifications 28 Limited Warranty Statement 29 End User Agreement 31 Federal Communication Commission Interference Statement 32 Regulatory Information to the user 33
TKP-7000 Introducing the TKP-7000 Thanks for purchasing URC's TKP-7000 in-wall touch-screen. Its easy, intuitive use will help simplify your life while adding control of more things than you thought possible. Enjoy some key features like: Rooms Menu With the touch of a single button, take control of your domain.
TKP-7000 Capacitive Touch screen Navigation just became easier; it's as simple as a “swipe” or “flick”. By incorporating gesture control, every screen can be explored by simple finger swipes while the on-board accelerometer supports flicking. Time & Weather Module A simple button press opens the Time & Weather Module; a full screen display keeping you “up to date” with today's time, date and weather conditions.
TKP-7000 Installing the TKP-7000 The TKP-7000 is wall-mountable and fits easily into a dual-gang opening. Prior to installation, make sure power is available at the preferred location.
TKP-7000 Installation Follow the diagram below for installation: 1. Make sure the dual-gang opening is fitted with a standard twogang trim box (available from the local electrical supplier/store) 2. Connect the Ethernet cable to the rear of the supplied TKP-7000 wall-plate. 3. Mount the wall-plate to the two-gang retro-box 4. The TKP-7000 easily snaps into place to the wall-plate.
TKP-7000 Main Menu Navigation Although specific screen design and certain options will be dictated by the custom integrator that programmed the Total Control System, the general layout will remain the same. Actual navigation is performed through screen swipes (Up/Down, Left/Right) while selecting any item is as simple as pressing the icon/text to be selected.
TKP-7000 Title Bar The Title Bar will be present on all TKP-7000 screens and contains valuable information during normal use. Easily find out the time, weather, now playing information and the room that the keypad is controlling. Time & Weather This data, found on the left-hand side of the Title Bar will show the current time, date and weather information. Pressing this area of the Title Bar will open the Time & Weather Module.
TKP-7000 Now Playing Appearing on the right-hand side of the Title Bar, this displays the source that is currently being used in the room that the keypad is controlling. • The Now Playing display will show the device that is being used (in this case, William's iPod), associated artwork, and metadata information is displayed since it is a URC media device. The metadata will change, every 5 seconds, rotating between song, artist and album.
TKP-7000 Categories/Devices Ribbon This ribbon will show the various categories of control that are available to the selected room. The quantity of categories is determined by the system setup and can vary from one to however many categories were programmed by the system designer. Although only seven categories can fit on the screen at any moment, navigate to other categories, if available, by swiping left or right.
TKP-7000 Status Bar The Status Bar, located directly above the Core Buttons, provides valuable status and feedback of the Total Control system. The four sections of the Status Bar are determined by the system programmer, and are customizable per keypad,so it is not possible to explain how your keypad looks; however, after reviewing the following possibilities, there should be no need for further explanation. Sunrise Time: Updated at midnight every day, this will show the sunrise time for the next day.
TKP-7000 Core Buttons These key system navigation buttons will always be present at the bottom of the screen. Vol-, Vol+ & Mute These audio controls will affect the volume for the room to which the TKP-7000 is assigned. See the Rooms Menu section of this manual for more details. Main Selecting this button will always return the user to the Main screen Shortcuts These user-configurable shortcuts allow the end-user to store up to 6 favorite activities.
TKP-7000 Power When pressed, this performs the Room Off function programmedby the custom integrator. If this button is pressed for greater than 3 seconds, the Power Menu appears. In this menu, it is possible to: • Turn Off the ROOM (this is the same as tapping the Power button). • Issue the House Off command, as programmed by the custom integrator. • Custom commands, programmed by the custom integrator, may also appear in this menu.
TKP-7000 Rooms Menu The Rooms Menu is the “landing” screen for a TKP-7000. This menu (see picture below) will be displayed whenever the keypad reboots, loses/regains power or is reset. The most common choice would be to select the room where the TKP-7000 is physically located, however, as we will discover, this is up to the user. The Rooms Menu is used to: • Temporarily Link rooms in a Total Control DMS system.
TKP-7000 Initial View (Room Monitoring) When the Rooms Menu opens up, the room list populates with all of the rooms in the Total Control project. Each room displays its status so the user can visually see what is “going on” in that room. The Exit button will return the user to the previous screen. Selecting a Room (Room Control) Selecting any room from the room list will allow the TKP-7000 to control that room, as if it were physically in that room.
TKP-7000 Linking Rooms (DMS Audio only) Selecting the Link Rooms button will open up the Link Rooms screen with the current room already selected. Only rooms/areas that are part of the DMS family of products will appear. Select, using the check boxes, the rooms that you would like to LINK. Pressing the check box will alternately “check” and “uncheck” it. = The Go Back button will cause the screen to revert to the Room Menu without making any changes.
TKP-7000 Using Linked Rooms Once a room is linked, pressing the volume or mute buttons for that room will cause the Linked Rooms Volume Pop-Up to display All Linked Rooms This menu will display the volume levels for all rooms in the temporary group. Selecting All Linked Rooms results in the volume and mute commands to operate ALL rooms (e.g. Volume Up will cause the volume in all linked rooms to rise simultaneously, and at the same rate).
TKP-7000 Time & Weather Module This module displays information about the time, date and local weather. Pressing on the Time, Date & Weather display in the Title Bar of the TKP-7000 opens the Time & Weather Module. = Selecting Exit will return to the previous screen = Selecting Night Mode will place the TKP-7000 into a low light mode to prevent it from overpowering a dark room. This mode will disable any photo slideshow or screen time-out time andremain in this mode until touched again.
TKP-7000 Shortcuts Pop-Up The Shortcuts Pop-Up menu is designed to give the user the ability to select their most frequently used devices/activities and place them within an easy to reach menu. There are a maximum of six (6) shortcuts per room location. Remember, regardless of the physical location of the TKP-7000, it may still access, via the Rooms menu, any of the other rooms in the Total Control system (dependent upon programming). Each room can be assigned up to 6 shortcuts in this menu.
TKP-7000 Select up to 6 devices/activities by selecting the check box shown for each possibility. Once all 6 are chosen, the remaining devices/activities will be grayed out to show there are no more choices to be made. Reorder devices by selecting the reorder icon at the top of the Add/Edit window; this opens the reorder Items list. If you would like to change the order in which the activities/devices appear, drag the items, using the “grabber” on the right side of the boxes to rearrange them.
TKP-7000 Adjusting User Settings on the TKP-7000 By pressing and holding the Main and Mute buttons for 5 seconds (found in the Core Menu) simultaneously the TKP-7000 Settings Menu will appear. Simultaneously press both the Main and Mute buttons to activate the Settings Menu. Settings Menu The Settings Menu allows you to adjust some basic parameters of the TKP-7000 keypad. Select these options by pressing the appropriate icon.
TKP-7000 Sleep Settings Decide upon the option that best fits the current needs. LCD Screen is always ON: This option keeps the LCD screen illuminated at all times LCD Screen will turn OFF: This option allows the user to decide on the amount of time that the LCD screen will remain illuminated after it is last used. The + and – buttons will adjust the time frame up or down accordingly.
TKP-7000 General The General settings screen allows for setting the Time, Date and decide on the scale used to display the temperature(Fahrenheit/Celsius). To view the rest of the General settings menu, be sure to scroll up/down. Using the arrow found at the left and right sides of each property (hour, minutes, month, etc.) adjusts the value up, or down, respectively.
TKP-7000 Sound By default, the TKP-7000 emits a low volume beep as a confirmation tone for screen presses. Use this menu to adjust thesound to your liking. Use the + or – buttons to raise or lower the volume of the confirmation beep. Selecting OK will accept any changes made and return to the Main menu, as well as selecting Cancel will return the user to the Main menu, without incorporating any changes.
TKP-7000 Brightness Determine the overall brightness of the TKP-7000's display, or incorporate a light sensor that will adjust the brightness of the unit based upon ambient room lighting. Use the + or – buttons to raise or lower the level of brightness. Selecting Enable Light Sensor disables the Brightness Level selection and dynamically adjust the LCD brightness based upon the ambient room lighting detected by the light sensor.
TKP-7000 Vibration Use this menu to adjust the TKP-7000’s touch screen sensitivity level. Use the + or – buttons to raise or lower the sensitivity level. Selecting OK will accept any changes made and return to the Main menu, as well as selecting Cancel will return the user to the Main menu, without incorporating any changes.
TKP-7000 System Although none of the information can be modified, these System Pages will show important information about your TKP-7000. These pages should only be needed by a custom install professional, or technical support.
TKP-7000 Network This option will show important information about the current network, its settings and give the ability to edit the IP address of the TKP-7000. Be careful, these settings should only be edited by a professional. Entering values without specific information or instruction could easily result in the TKP-7000 failing to function correctly.
TKP-7000 Factory Default This should only be attempted by a custom install professional that is familiar with Total Control, or under instruction from the manufacturer.
TKP-7000 Rebooting Your TKP-7000 Using the physical RESET button found on the silver keypad bezel (bottom right-hand corner) will power-cycle the unit. This is the first option to try, if the screen freezes or the unit becomes unresponsive.
TKP-7000 Limited Warranty Statement 1. Limited Warranty and Disclaimers Universal Remote Control, Inc. (“URC”) warrants that the URC equipment shall be free from defects in material and workmanship under normal usage for one (1) year from purchase when such is purchased from URC. This limited warranty is valid only in the United States of America. URC warrants that the software will substantially conform in any material respect to its functional specifications at the time of delivery.
TKP-7000 WITHOUT IN ANY WAY LIMITING THE GENERALITY OF THE OTHER PROVISIONS HEREIN, WARRANTY DOES NOT COVER: (I) DAMAGE FROM MISUSE, NEGLECT OR ACTS OR NATURE, (II) MODIFICATIONS, (III) INTEGRATION WITH THIRD PARTY CONTENT (IV) BEYOND THE WARRANTY PERIOD AND/ OR FAILURE TO FOLLOW URC WARRANTY CLAIM PROCEDURE.
TKP-7000 URC’s PC programmable remotes or any of our Total Control® whole-house equipment are authorized for online internet sales. Buying URC’s PC programmable remotes or any of our Total Control® whole-house equipment online means buying equipment that does not have a URC’s limited warranty. Such equipment is not eligible for URC tech support or software support, either. 2.
TKP-7000 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
TKP-7000 Regulatory Information to the user n CE conformity Notice Products with “CE” marking comply EMC Directive 2004/108/EC, issued by the commission of the European Community. 1) EMC Directive lEmission : EN 55022 lImmunity : EN 55024 lPower : EN-61000-3-2, 3 n Declaration of Conformity “Hereby, Universal Remote Control Inc. declares that this TKP-2000 is in compliance with the Essential requirements and other relevant provisions of EMC Directive 2004/108/EC.” Certification Type No.(Model No.
TKP-7000 Declaration of Conformity Company Name : Universal Remote Control Inc. Company Address : Contact Information : 500 Mamaroneck Avenue, Harrison, NY 10528, U.S.A www.universalremote.
NOTE Page 35
500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 www.universalremote.
