Owner’s Manual MRX-2 Network Base Station
MRX-2 Owner’s Manual ©2013 Universal Remote Control, Inc. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this manual may be subject to change without prior notice.
TABLE OF CONTENTS Introduction 1 Features and Benefits 2 Parts Guide 3 Front and Rear Panel Descriptions 4 Network Installation 6 Specifications 7 Limited Warranty Statement 8 End User Agreement 10 Federal Communication Commission Interference Statement 11 Declaration of Conformity 12
MRX-2 NETWORK BASE STATION Introduction The MRX-2 Network Base Station allows for control of your components by sending infrared and serial commands to your system. This base station can be used with either a Total Control or a Complete Control system. When used in a Total Control System: Expand zones throughout the home or commercial space by installing multiple MRX-2’s. Control equipment such as shades and TV lifts using the base stations sensors, relays and RS-232 ports.
MRX-2 NETWORK BASE STATION Features and Benefits When used in a Total Control System: Expand Control: Add an MRX-2 to a Total Control system to expand control to other rooms/areas in the home or office. Components located out of reach from the MRX Advanced Network System Controller may be controlled via IR, RS-232 or Relays by using an MRX-2 to expand the scope of a Total Control system. Lighting Control: By connecting an optional RFTX-1 RF Transmitter, take control of your URC lighting (within range).
MRX-2 NETWORK BASE STATION Parts Guide The MRX-2 Network Base Station includes: 1 - MRX-2 Network Base Station 1 - 12V-1000mA Power Supply 6 - Visible Emitters with 10 foot plug in cables including 1 pink sleeved emitter for the RFTX-1 port 1 - Two Meter 3.5mm Stereo to 3.
MRX-2 NETWORK BASE STATION Front and Rear Panel Descriptions Front The front panel consists of 4 indicator lights which will illuminate when in use. Power Status Sensor Ethernet Reset: Bottom Power: Illuminates when the power supply is connected to an outlet. Status: Flashes blue when an RF or Network signal is received. Sensor: Illuminates to indicate when the sensor is activated. Ethernet: Illuminates when connected to an active network.
MRX-2 NETWORK BASE STATION Rear The rear panel ports are: Power Relay:NO, NC, COM IR Outputs: #1-6 RFTX Port: #6 Sensor Ethernet RS-232 Ports IR IN RF IN RF ID RF Out Power: Uses the included 12V/1Amp power supply. LAN: Plug an ethernet cable (RJ45) to the LAN(Local Area network). Relay NO, NC, COM: Configurable switch closure control. RS-232 Ports: Two RS232 ports provide direct control. Sensor: Connect with one of URC’s or compatible third party, sensors.
MRX-2 NETWORK BASE STATION Network Installation The MRX-2 can be installed in either a Total Control or a Complete Control System. Connect the Ethernet cable (RJ45) to the rear of the MRX-2 and the other end to the active network.
MRX-2 NETWORK BASE STATION Specifications Network: One 10/100 Ethernet port Relay: One relay configurable to be NO, NC or Momentary Sensor: One sensor supports Video or Voltage sensing via URC sensors. RS-232: Two RS-232 ports support TX, RX and GND two way communication via URC cables.
MRX-2 NETWORK BASE STATION Limited Warranty Statement 1. Limited Warranty and Disclaimers Universal Remote Control, Inc. (“URC”) warrants that the URC equipment shall be free from defects in material and workmanship under normal usage for one (1) year from purchase when such is purchased from URC. This limited warranty is valid only in the United States of America. URC warrants that the software will substantially conform in any material respect to its functional specifications at the time of delivery.
MRX-2 NETWORK BASE STATION SKILL AND CARE, OR OUTCOME OR RESULTS. WITHOUT IN ANY WAY LIMITING THE GENERALITY OF THE OTHER PROVISIONS HEREIN, WARRANTY DOES NOT COVER: (I) DAMAGE FROM MISUSE, NEGLECT OR ACTS OR NATURE, (II) MODIFICATIONS, (III) INTEGRATION WITH THIRD PARTY CONTENT (IV) BEYOND THE WARRANTY PERIOD AND/ OR FAILURE TO FOLLOW URC WARRANTY CLAIM PROCEDURE.
MRX-2 NETWORK BASE STATION equipment are authorized for online internet sales. Buying URC’s PC programmable remotes or any of our Total Control® whole-house equipment online means buying equipment that does not have a URC’s limited warranty. Such equipment is not eligible for URC tech support or software support, either. 2.
MRX-2 NETWORK BASE STATION Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MRX-2 NETWORK BASE STATION Declaration of Conformity Company Name : OH SUNG ELECTRONICS CO., LTD.
NOTE Page 13
NOTE Page 14
NOTE Page 15
500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 www.universalremote.