Owner’s Manual CAM-DC-I Indoor Network Camera
CAM-DC-I Indoor IP Camera Owners Manual ©2014 Universal Remote Control, Inc. The information in this Owner’s Manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc. Universal Remote Control, INC. shall not be liable for operational, technical or editorial errors/omissions made in this manual. The information in this Owner’s Manual may be subject to change without prior notice.
TABLE OF CONTENTS Introduction 1 Features and Benefits 1 Parts Guide 1 CAM-DC-I Description 2 Basic Installation 3 Communicating with the Camera 4 Navigating the Web Interface - Live View 5 Navigating the Web Interface - Admin 6 Specifications 7 Limited Warranty Statement 8 End User Agreement 11 Federal Communication Commission Interference Statement 12 Regulatory Information to the user 13 Declaration of Conformity 14
CAM-DC-I INDOOR NETWORK CAMERA Introduction Congratulations on your purchase of the CAM-DC-I Indoor Surveillance Dome IP Camera! The CAM-DC-I is an indoor IP camera that allows for seamless viewing over the network with Total Control interfaces such as the TRC-1280, TKP-2000, TKP-7000 and future Total Control graphical interfaces. Once networked, it relays video to these devices or your PC.
CAM-DC-I INDOOR NETWORK CAMERA CAM-DC-I Description Front View Dome Cover OPEN LAN connection CLOSE Dome Cover: Mini dome cover twists to open and close. Open the dome cover to reveal the lens and position it to the correct viewing angle. Note: If you need to focus the lens, turn it until the image is clear. LAN: Plug an Ethernet cable from the camera’s LAN connection to a PoE router or switch like URC's MFS-POE8. (If a PoE switch is not used, you must use a PoE injector to supply power to the camera.
CAM-DC-I INDOOR NETWORK CAMERA Basic Installation Follow these basic steps to install the Indoor Network Camera CAM-DC-I. 1. Fasten the camera to your planned location. 2. Plug an ethernet cable to the LAN port of the camera. Note: No separate power supply is needed as the camera receives power via a PoE supply or a MFSPOE-8 router.
CAM-DC-I INDOOR NETWORK CAMERA Communicating with the Camera An IP address is required to view the camera and modify surveillance options. Once installed, locate the IP address assigned by your router (which will differ from the default address below). Your router contains a DHCP table which displays each connected device and its IP address. IP addresses normally resemble 10.20.30.40 or 192.168.1.xx. For further information, refer to the router’s documentation.
CAM-DC-I INDOOR NETWORK CAMERA Navigating the Web Interface - Live View Select from the options below to modify the Live View. Control Bar Channel Control Displays multiple camera streams. It modifies the primary and secondary streams (frame rate, image size, encoding, camera name, rate control mode, image quality and group of pictures structure) from the Admin page (Device Configuration> Camera & Motion). Show Full/Normal Screen View live video in either full or normal screen.
CAM-DC-I INDOOR NETWORK CAMERA Navigating the Web Interface - Admin Use the Admin interface to modify advanced features for the camera. To gain acccess to the Admin site, enter the default username and password(root and root). Quick Configuration: A guided step-by-step walkthrough to setup your camera’s configuration settings. Setup your Server Name Setup, Date & Time, Network Configuration and IP-CCTV DNS Setup.
CAM-DC-I INDOOR NETWORK CAMERA Specifications Camera Type Image Sensor Indoor / Outdoor Use Lens Min. illumination Video Compression Video Resolution Image quality Control Max Streaming Speed Motion Detection Network Bandwdth Control Network Protocol Viewer Remote Admin.
CAM-DC-I INDOOR NETWORK CAMERA Limited Warranty Statement 1. Limited Warranty and Disclaimers Universal Remote Control, Inc. (“URC”) warrants that the URC equipment shall be free from defects in material and workmanship under normal usage for two (2) years from purchase when such is purchased from URC. This limited warranty is valid only in the United States of America.
CAM-DC-I INDOOR NETWORK CAMERA OF CORRECTNESS, ACCURACY, RELIABILITY OR OTHERWISE. EXCEPT AS EXPRESSLY PROVIDED FOR HEREIN, TECHNICAL SERVICES ARE SUPPLIED “AS IS”, WITHOUT ANY WARRANTY, EXPRESS, STATUTORY OR IMPLIED, OF ANY KIND. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, URC EXPRESSLY DISCLAIMS ALL WARRANTIES, EXPRESS, STATUTORY OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF QUALITY OR REASONABLE SKILL AND CARE, OR OUTCOME OR RESULTS.
CAM-DC-I INDOOR NETWORK CAMERA website available at www.universalremote.com or call the Customer Service Center at (914) 835-4484. This limited warranty only covers the URC equipment issues caused by defects in material or workmanship during ordinary consumer use.
CAM-DC-I INDOOR NETWORK CAMERA THE LIMITATIONS OF LIABILITY MAY NOT APPLY TO END USER IN WHOLE OR IN PART, WHERE SUCH ARE RESTRICTED LIMITED OR EXCLUDED BY APPLICABLE LAW AND SUCH SHALL APPLY TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW. URC SHALL NOT BE HELD RESPONSIBLE FOR THE STATEMENTS MADE BY OTHERS.
CAM-DC-I INDOOR NETWORK CAMERA Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CAM-DC-I INDOOR NETWORK CAMERA Regulatory Information to the user n CE conformity Notice Products with “CE” marking comply EMC Directive 2004/108/EC, issued by the commission of the European Community. 1) EMC Directive lEmission : EN 55022 lImmunity : EN 50130-4 lPower : EN-61000-3-2, 3 n Declaration of Conformity “Hereby, Universal Remote Control Inc. declares that this CAM-DC-I is in compliance with the Essential requirements and other relevant provisions of EMC Directive 2004/108/EC.
CAM-DC-I INDOOR NETWORK CAMERA Declaration of Conformity Company Name : Universal Remote Control Inc. Company Address : Contact Information : Brand Name : 500 Mamaroneck Avenue, Harrison, NY 10528, U.S.A www.universalremote.
NOTE Page 15
500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 www.universalremote.
