Doc. Title Originator User Guide for UNA Module and Socket EVB (V23) Max Shu Date 2012/09/07 Version DVT V23 The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
Revision Record Version 1.0 1.1 Revise content New release 1.Add EVB test point pin define 2. Identification of PCB version Date 2012-08-10 2012-09-07 The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
Content 1. FCC Regulations............................................................................................ 3 2. RF Exposure Information.............................................................................. 4 3. Information of Installed Module.................................................................... 5 4. Guide to Use ..................................................................................................
1. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
2. RF Exposure Information This Modular Approval is limited to OEM installation for mobile and fixed applications only. The antenna installation and operating configurations of this transmitter, including any applicable source-based time-averaging duty factor, antenna gain and cable loss must satisfy MPE categorical Exclusion Requirements of §2.1091.
3. Information of Installed Module Module Name UNA_850 FCC ID IXM-UNA850 HW Version V2.3 SW Version V3.1a GSM Band GSM 850, E-GSM 900, DCS 1800, PCS 1900 UMTS Band FDD I, FDD V GSM Feature Release 99 GPRS Release 6, Multi-slot class 12 EDGE Release 6, Multi-slot class 12 UMTS Feature HSDPA, HSUPA (UMTS Release 6) AT Command 3GPP TS 27.007, 27.005 SIM/USIM Support 3V and 1.8V Interface USB 2.
4. Guide to Use 1) Function of Socket EVB V23 and Identification of PCB version The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
Function Description Available USB PORT Connect to Host PC and Download Firmware V Power supply IN Optional Connect to external Power supply input V UART1 Download Firmware V RF SMA connector Connect to external Antenna V SIM card Connect to SIM card V LINE IN Connect to Line in V LINE OUT Connect to Line out V J51 MP test connector V J52 MP test connector V Unavailable The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd.
2) Configure the Socket EVB Default JUMP Setting : Component reference Function Jump 1-2 J40 Enable VBAT_M. (Default) R808 short. No, Note1 J41 Enable VBAT_M1.(Default) R809 short. No, Note2 Note1 :For current measurement of VBAT_M: de-solder R808. Close J40 Note2 :For current measurement of VBAT_M1: de-solder R809. Close J41 Component reference J42 Component reference Function Jump 1-2 (Default) Output +3.3V for module No Output +4.
Download Key : Component reference J31 Function Enable Download through USB Jump 1-2 No, Note3 Note 3: To enable download mode, Please close J31 and refer to “ Use Data Card Tool To Update Image File Steps-V1.1-2012.07.18.pdf” Jump setting for normal mode . Component reference JUMP 1-2 J40 NO J41 NO J42 NO J31 NO J45 NO The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd.
J53 NO Jump setting for Download mode : Component reference JUMP 1-2 J40 NO J41 NO J42 NO J31 YES J45 NO J53 NO The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
3) Insert the SIM card To use a UNA module, you need to install: a. A live SIM card (with an active account), or b. A test SIM card for use with call box (for example ,an Agilent 8960 ..) To install the SIM card: a. Place the Socket EVB face-up(as shown) – the SIM slot is on right side. b. Note the location of the notched corner of the card in the following image. c. Inset the SIM card into the slot. The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd.
4) Place the Module After inserting the SIM card, insert the module: a. Place the Socket EVB face-up(as shown) – the socket is in the center. b. Notice the pin 1 location on the socket. The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
5) Connect the antenna After installing the Module ,connect the supplied antenna to the EVB a. Place the Socket EVB face-up. The antenna connector on the bottom side. b. Connect the antenna to the adapter. The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
6) Download setting a. Plug in the Jump. b.Connect the USB cable between EVB & PC. The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
7) Manual control module sleep mode: Component reference J45 Function USB_EN input for sleep / normal mode a. Follow UNA IO application design notes b. Plug in the Jump from J45 before use manual control. c. Connect J51,16pin to control module . J51,16pin: Hi(3.3~5.0V): Normal mode ; Low(0~0.3V): Sleep mode The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd.
8) Apply External power to module To use external power for module, please follow the steps to setting. a. b. c. d. Red line VCC connect to J38. Black line GND connect to J39. De-solder the open pad R808.(yellow circle) USB cable connect to Host PC. The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
9) Measure current of module setting a. De-solder the open pad R809.(yellow circle) b. Please follow the photo to setup the current meter. The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
10) Connect extend cable for line in & line out : The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
11) EVB test point pin define 1. J52 Pin define Pin number Pin name 1 GND 3 DAICLK 5 7 9 11 13 15 DAIPCMOUT SCL SDA Reserve Pin URXD2 URXD1 Pin number Pin name 2 VBAT_M1 4 DAISYNC 6 8 10 12 14 16 DAIPCMIN DAIRST Reserve Pin Reserve Pin UTXD2 UTXD1 The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
2.J51 Pin define Pin number Pin name 1 GND 3 Wake 5 7 9 11 13 15 #EINT9 GPIO2 GPIO0 Reserve Pin KROW0 Reserve Pin Pin number Pin name 2 AP_Ready 4 #W_Disable 6 8 10 12 14 16 ID GPIO1 #Sys_config Reserve Pin KCOL6 Reserve Pin (Note4) (Note5) Note4: Default- open (900 module);If use 850 module, this pin to pull low(1kΩ Ω). Note5: enable "USB+UART "mode- Default- open (USB only);If use”USB+UART” mode, this pin to pull low(1kΩ Ω).
