Model MIB3050S Model MI3050S Model MI3050SB Conforms to UL Std. 217 MODEL MI3050S Single Station Smoke Alarm UNIVERSAL SMOKE SENSING TECHNOLOGY 2-in-1 SMOKE & FIRE ALARM WITH 10 YEAR PERMANENT POWER SEALED BATTERY READ ALL INSTRUCTIONS THANK YOU for purchasing this smoke and fire alarm. This alarm does not require battery changes. The tamper proof permanent power sealed battery which will last for approximately 10 years.
SMOKE ALARM LIMITATIONS AND FUNCTIONS l l l l l l l l l l l l l l l l There are three basic smoke alarm types: Universal Smoke Sensing Technology®, Ionization and Photoelectric. Universal Smoke Sensing Technology® is an ionization alarm containing patented Smart Alarm Technology. Alarms containing Universal Smoke Sensing Technology are effective at detecting fast flaming fires and slow smoldering fires.
RECOMMENDED LOCATION OF ALARMS • Locate the first smoke alarm in the immediate area of the bedrooms. Try to protect the escape route as the bedrooms are usually farthest from an exit. If more than one sleeping area exists, locate additional smoke alarms in each sleeping area. If a hall is more than 40 feet (12 meters) long, install a smoke alarm at each end. • Locate additional smoke alarms to protect any stairway as stairways act like chimneys for smoke and heat.
AVOID THESE LOCATIONS • • the garage – products of combustion are produced when you start your vehicle. near appliances or areas where normal combustion regularly occurs (kitchens, near furnaces, gas hot water heaters). Use smoke alarms with U.S.S.T.® or photoelectric sensors, or smoke alarms with Silence Feature for these areas. in areas with high humidity, like bathrooms or areas near dishwashers or washing machines. Install at least 3 feet (0.9 meters) away from these areas.
1. Detach the breakaway alarm locking pin from the mounting bracket. 2. Insert the pin into the hole in the side of the alarm after the alarm has been installed on the mounting plate. Refer to the diagram below for correct placement. FIGURE 1 INSERT ALARM LOCKING PIN HERE (optional) TO DEACTIVATE THE LOCKING FEATURES: To remove the smoke alarm for cleaning or servicing, you must first remove the locking pin, if it has been installed. 1. Use long nose pliers to pull the locking pin out of the hole. 2.
IMPORTANT CONSIDERATIONS YOUR ALARM HAS BEEN DESIGNED WITH A PRODUCT END-OF-SERVICE LIFE WARNING WHICH WILL SOUND AFTER APPROXIMATELY 10 YEARS OF OPERATION FROM INITIAL POWER UP. NOTE: MANUFACTURER RECOMMENDS REPLACEMENT OF THIS ALARM 10 YEARS AFTER DATE OF INSTALLATION. NOTE: NUMEROUS ALARMS OR PROLONGED ALARMING IS NOT TYPICAL AND WILL CONSUME THE BATTERY CAPACITY, SHORTENING THE LIFE OF THIS PRODUCT. NEVER use an open flame of any kind to test this smoke alarm.
Deactivation of the alarm is permanent. Do not attempt to open the alarm for any reason. Place this alarm into shut-down mode at the end of its useful service life. Once the smoke alarm has entered end-of-service-life mode, it is necessary to deactivate the alarm operation. This will stop the product end-of-service-life warning signal and also discharge the remaining capacity of the battery to render it safe for disposal. 1.
REPAIRS AND SERVICES This smoke alarms contains less than 1 microcurie (37 kilobecquerel) of Americium 241, a radioactive material. The distribution of these ionization-type smoke alarms is licensed by the U.S. Nuclear Regulatory Commission; the consumer is exempt from any licensing or requirements. If the smoke alarm is defective in any way, do not tamper with the smoke alarm. Return the smoke alarm for servicing. (See warranty for instructions or in-warranty returns.
QUICK REFERENCE GUIDE / OPERATIONAL SUMMARY CONDITION ALARM AUDIBLE & VISUAL SIGNALS HORN RECOMMENDATION RED LED New - Out of Package Silent Off DC Power is Present Silent Blinks On once approx every 2 minutes The alarm is operating properly. Test/Silence Button Has Been Pressed 3 beeps, 2 second pause, Repeat Blinks On in sync with Horn The alarm is operating properly.
MODEL MI3050S TEN-YEAR LIMITED WARRANTY USI Electric, Inc. /Universal Security Instruments, Inc. (“USI”) warrants this product to be free from defects in material and workmanship for a period of 10 (ten) years from the date of purchase. This warranty shall not apply to any damage which may be caused by the sealed batteries used in this product. This warranty applies only to the original consumer purchaser and only to products used in normal residential use and service.
MODEL MDSK300S MODEL MDS300S Conforms to UL Std. 217 MODEL MDS300S Single Station Smoke Alarm UNIVERSAL SMOKE SENSING TECHNOLOGY ® 2-in-1 SMOKE AND FIRE ALARM WITH 10 YEAR PERMANENT POWER SEALED BATTERY READ ALL INSTRUCTIONS THANK YOU for purchasing this smoke and fire alarm. This alarm does not require battery changes. It has a permanent power sealed battery which will last for approximately 10 years.
SMOKE ALARM LIMITATIONS AND FUNCTIONS There are three basic smoke alarm types: Universal Smoke Sensing Technology®, Ionization and Photoelectric. Universal Smoke Sensing T echnology® is an ionization alarm containing patented Smart Alarm Technology. Alarms containing Universal Smoke Sensing Technology are very effective at detecting fast flaming fires, and also respond very quickly to slow smoldering fires.
RECOMMENDED LOCATION OF ALARMS • Locate the first smoke alarm in the immediate area of the bedrooms. Try to protect the escape route as the bedrooms are usually farthest from an exit. If more than one sleeping area exists, locate additional smoke alarms in each sleeping area. If a hall is more than 40 feet (12 meters) long, install a smoke alarm at each end. • Locate additional smoke alarms to protect any stairway as stairways act like chimneys for smoke and heat.
AVOID THESE LOCATIONS • the garage – products of combustion are produced when you start your vehicle. • near appliances or areas where normal combustion regularly occurs (kitchens, near furnaces, gas hot water heaters). Use smoke alarms with IoPHIC ® or photoelectric sensors, or smoke alarms with Silence Feature for these areas. • in areas with high humidity, like bathrooms or areas near dishwashers or washing machines. Install at least 3 feet (0.9 meters) away from these areas.
1. Detach the breakaway alarm locking pin from the mounting bracket. 2. Insert the pin into the hole in the side of the alarm after the alarm has been installed on the mounting plate. Refer to the diagram below for correct placement. FIGURE 1 INSERT ALARM LOCKING PIN HERE (optional) TO DEACTIVATE THE LOCKING FEATURES: To remove the smoke alarm for cleaning or servicing, you must first remove the locking pin, if it has been installed. 1. Use long nose pliers to pull the locking pin out of the hole. 2.
IMPORTANT CONSIDERATIONS YOUR ALARM HAS BEEN DESIGNED WITHA PRODUCT END-OF-SERVICE LIFE WARNING WHICH WILL SOUND AFTER APPROXIMATELY 10 YEARS OF OPERATION FROM INITIAL POWER UP. NOTE: MANUF ACTURER RECOMMENDS REPLACEMENT OF THIS ALARM 10 YEARS AFTER DA TE OF INSTALLATION. NOTE: NUMEROUS ALARMS OR PROLONGED ALARMING IS NOT TYPICALAND WILL CONSUME THE BATTERY CAPACITY, SHORTENING THE LIFE OF THIS PRODUCT. NEVER use an open flame of any kind to test this smoke alarm.
Deactivation of the alarm is permanent. Do not attempt to open the alarm for any reason. Place this alarm into shut-down mode at the end of its useful service life. Once the smoke alarm has entered end-of-service-life mode, it is necessary to deactivate the alarm operation. This will stop the product end-of-service-life warning signal and also discharge the remaining capacity of the battery to render it safe for disposal. 1.
WHAT TO DO WHEN THE ALARM SOUNDS o Leave immediately by your plan of escape. Every second counts, so don't waste time getting dressed or picking up valuables. o In leaving, don't open any inside door without first feeling its surface. If hot, or if you see smoke seeping through cracks, don't open that door! Instead, use your alternate exit. If inside door is cool, place your shoulder against it, open it slightly and be ready to slam it shut if heat and smoke rush in.
QUICK REFERENCE GUIDE / OPERATIONAL SUMMARY CONDITION ALARM AUDIBLE & VISUAL SIGNALS HORN RECOMMENDATION RED LED New - Out of Package Silent Off DC Power is Present Silent Blinks On once approx every 2 minutes The alarm is operating properly. Test/Silence Button Has Been Pressed 3 beeps, 2 second pause, Repeat Blinks On in sync with Horn The alarm is operating properly.
PRODUCT TEN-YEAR LIMITED WARRANTY MODEL MDS300S, MDSK300S UNIVERSAL SECURITY INSTRUMENTS, INC. (“USI”) warrant s your product to be free from defects in material and workmanship for a period of ten (10) years from the date of purchase. This warranty shall not apply to any batteries used in the product or to any damage which may be caused by such batteries. This warranty applies only to the original consumer purchaser and only to products used in normal residential use and service.
WHAT YOU SHOULD KNOW ABOUT CO Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless, tasteless gas. It is a cumulative poison. Even low levels of CO have been shown to cause brain and other vital organ damage in unborn infants with no effect on the mother. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household: MILD EXPOSURE: Slight headache, nausea, vomiting, fatigue (often described as “flu-like” symptoms).
ALARM TECHNOLOGY & FEATURES This is a 3-in-1 combination smoke + fire + carbon monoxide (CO) alarm. The 10 year sealed battery provides continuous protection even in the event of a power outage. • There are three basic smoke alarm types: Universal Smoke Sensing Technology®, Ionization and Photoelectric. • Universal Smoke Sensing Technology® is an ionization alarm containing patented Smart Alarm Technology.
ALARM TECHNOLOGY & FEATURES This is a 3-in-1 combination smoke + fire + carbon monoxide (CO) alarm. The 10 year sealed battery provides continuous protection even in the event of a power outage. • There are three basic smoke alarm types: Universal Smoke Sensing Technology®, Ionization and Photoelectric. • Universal Smoke Sensing Technology® is an ionization alarm containing patented Smart Alarm Technology.
ALARM TECHNOLOGY & FEATURES This is a 3-in-1 combination smoke + fire + carbon monoxide (CO) alarm. The 10 year sealed battery provides continuous protection even in the event of a power outage. • There are three basic smoke alarm types: Universal Smoke Sensing Technology®, Ionization and Photoelectric. • Universal Smoke Sensing Technology® is an ionization alarm containing patented Smart Alarm Technology.
ALARM TECHNOLOGY & FEATURES This is a 3-in-1 combination smoke + fire + carbon monoxide (CO) alarm. The 10 year sealed battery provides continuous protection even in the event of a power outage. • There are three basic smoke alarm types: Universal Smoke Sensing Technology®, Ionization and Photoelectric. • Universal Smoke Sensing Technology® is an ionization alarm containing patented Smart Alarm Technology.
ALARM TECHNOLOGY & FEATURES This is a 3-in-1 combination smoke + fire + carbon monoxide (CO) alarm. The 10 year sealed battery provides continuous protection even in the event of a power outage. • There are three basic smoke alarm types: Universal Smoke Sensing Technology®, Ionization and Photoelectric. • Universal Smoke Sensing Technology® is an ionization alarm containing patented Smart Alarm Technology.
ALARM TECHNOLOGY & FEATURES This is a 3-in-1 combination smoke + fire + carbon monoxide (CO) alarm. The 10 year sealed battery provides continuous protection even in the event of a power outage. • There are three basic smoke alarm types: Universal Smoke Sensing Technology®, Ionization and Photoelectric. • Universal Smoke Sensing Technology® is an ionization alarm containing patented Smart Alarm Technology.
ALARM TECHNOLOGY & FEATURES This is a 3-in-1 combination smoke + fire + carbon monoxide (CO) alarm. The 10 year sealed battery provides continuous protection even in the event of a power outage. • There are three basic smoke alarm types: Universal Smoke Sensing Technology®, Ionization and Photoelectric. • Universal Smoke Sensing Technology® is an ionization alarm containing patented Smart Alarm Technology.
ALARM TECHNOLOGY & FEATURES This is a 3-in-1 combination smoke + fire + carbon monoxide (CO) alarm. The 10 year sealed battery provides continuous protection even in the event of a power outage. • There are three basic smoke alarm types: Universal Smoke Sensing Technology®, Ionization and Photoelectric. • Universal Smoke Sensing Technology® is an ionization alarm containing patented Smart Alarm Technology.
WHAT YOU SHOULD KNOW ABOUT CO Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless, tasteless gas. It is a cumulative poison. Even low levels of CO have been shown to cause brain and other vital organ damage in unborn infants with no effect on the mother. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household: MILD EXPOSURE: Slight headache, nausea, vomiting, fatigue (often described as “flu-like” symptoms).
WHAT YOU SHOULD KNOW ABOUT CO Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless, tasteless gas. It is a cumulative poison. Even low levels of CO have been shown to cause brain and other vital organ damage in unborn infants with no effect on the mother. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household: MILD EXPOSURE: Slight headache, nausea, vomiting, fatigue (often described as “flu-like” symptoms).
WHAT YOU SHOULD KNOW ABOUT CO Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless, tasteless gas. It is a cumulative poison. Even low levels of CO have been shown to cause brain and other vital organ damage in unborn infants with no effect on the mother. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household: MILD EXPOSURE: Slight headache, nausea, vomiting, fatigue (often described as “flu-like” symptoms).
WHAT YOU SHOULD KNOW ABOUT CO Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless, tasteless gas. It is a cumulative poison. Even low levels of CO have been shown to cause brain and other vital organ damage in unborn infants with no effect on the mother. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household: MILD EXPOSURE: Slight headache, nausea, vomiting, fatigue (often described as “flu-like” symptoms).
WHAT YOU SHOULD KNOW ABOUT CO Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless, tasteless gas. It is a cumulative poison. Even low levels of CO have been shown to cause brain and other vital organ damage in unborn infants with no effect on the mother. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household: MILD EXPOSURE: Slight headache, nausea, vomiting, fatigue (often described as “flu-like” symptoms).
WHAT YOU SHOULD KNOW ABOUT CO Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless, tasteless gas. It is a cumulative poison. Even low levels of CO have been shown to cause brain and other vital organ damage in unborn infants with no effect on the mother. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household: MILD EXPOSURE: Slight headache, nausea, vomiting, fatigue (often described as “flu-like” symptoms).
Models MC304S, MCD305S Carbon Monoxide Alarm with 10 Year Permanent Power Sealed Battery Certified to Standard UL 2034 Single Station Carbon Monoxide Alarm PLEASE READ AND SAVE! THANK YOU for purchasing this Carbon Monoxide alarm. This alarm does not require battery changes. It has a permanent power sealed battery which will last for 10 years. It is designed to detect carbon monoxide which reaches the sensor. It is not designed to detect fire, heat, flames or any other gas.
WHAT YOU SHOULD KNOW ABOUT CO Carbon Monoxide (CO) is an insidious poison. It is a colorless, odorless, tasteless gas. It is a cumulative poison. Even low levels of CO have been shown to cause brain and other vital organ damage in unborn infants with no effect on the mother. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household: MILD EXPOSURE Slight headache, nausea, vomiting, fatigue (often described as “flu-like” symptoms).
INSTALLATION RECOMMENDATIONS Early warning is best achieved by the installation of alarms on all floors and areas of the household. WHERE THIS ALARM SHOULD BE INSTALLED • Install an alarm inside each bedroom where the occupant closes the door while sleeping. • An alarm should be installed in any family living unit containing a fuel-burning appliance or fireplace or having an attached garage.
FIGURE 2 • NOTE: For any location, make sure no door or other obstruction could prevent the Carbon Monoxide (CO) from reaching the alarm. WHERE THIS ALARM SHOULD NOT BE INSTALLED To avoid causing damage to the unit, to provide optimum protection, and to prevent unnecessary alarms. Do NOT locate this alarm: • In garages, kitchens, crawl spaces and unfinished attics. Avoid extremely dusty, dirty or greasy areas.
HOW TO INSTALL THIS CO ALARM IMPORTANT: Read all instructions before using this product. 1. Activate the Permanent Power battery feature by removing and discarding the battery pull tab. NOTE: Once activated, the alarm cannot be turned off without permanent deactivation. The alarm will remain on for the next ten years. 2. The alarm will sound one long beep to let you know it is powered up. The red power LED should be off and will blink on approx. every 2 minutes.
• Test the alarm once a week. If the alarm ever fails to test correctly, have it replaced immediately. If the alarm is not working properly, it cannot alert you to a problem. • This alarm must have battery power to operate. If the battery is dead, the alarm cannot operate. The sealed battery cannot be replaced. • This product is intended for use in ordinary indoor locations or family living units.
IF THE CO ALARM SOUNDS: 1. Operate TEST/SILENCE button; 2. Call your emergency services, fire department or 911. Write down the number of your local emergency service here: 3. Immediately move to fresh air - outdoors or by an open door/window. Do a head count to check that all persons are accounted for. Do not reenter the premises nor move away from the open door/window until the emergency services responders have arrived, the premises have been aired out and your alarm remains in its normal condition.
If the alarm does not sound properly: 1. Test the alarm again. If the alarm is still not working properly, replace it immediately. USING THE PEAK CO MEMORY (Digital Display Models Only): The CO Memory feature lets you check the highest level of CO recorded, since the last reset, and is displayed in parts per million (ppm) of carbon monoxide. To check CO memory: 1. Press and release the RESET/PEAK button on the alarm cover. The peak CO level is displayed on the screen.
CARBON MONOXIDE (CO) ALARM LIMITATIONS CO Alarms have limitations. Like any other electronic device, CO Alarms are not foolproof. CO Alarms have a limited operational life. Your CO Alarm must be tested weekly, because it could fail to operate at any time. If your CO Alarm fails to test properly, or if its self-diagnostic test reveals a malfunction, immediately have the unit replaced (see last page for warranty information). CO Alarms can only sense CO which reaches the alarm’s sensor.
• Check for exhaust backflow from CO sources. Check the draft hood on an operating furnace for a backdraft. Look for cracks on furnace heat exchangers. • Check the house or garage on the other side of a shared wall. • Keep windows and doors open slightly. If you suspect that CO is escaping into your home, open a window or a door. Opening windows and doors can significantly decrease CO levels.
MODEL MC304S and MCD305S TEN-YEAR LIMITED WARRANTY USI Electric, Inc. /Universal Security Instruments, Inc. (“USI”) warrants this product to be free from defects in material and workmanship for a period of 10 (ten) years from the date of purchase. This warranty shall not apply to any damage which may be caused by the sealed batteries used in this product. This warranty applies only to the original consumer purchaser and only to products used in normal residential use and service.