INSTALLATION & OPERATIONAL INSTRUCTIONS Manufactured by SpaWorldCorp. 5701 NW 35th Avenue Miami, Florida 33142 ASME A112.19.7-2006 ANSI-Z124.
INSTALLATION INSTRUCTIONS & OWNER’S MANUAL (Refer to individual model sheets for specifications) BEFORE BEGINNING INSTALLATION, CHECK THE FOLLOWING ITEMS AND READ THE INSTRUCTIONS CAREFULLY. CHECK ENTIRE UNIT FOR CONCEALED DAMAGE. If there is any damage, DO NOT INSTALL! Shipping damages must be reported to the carrier immediately. All damage must be discovered and reported prior to installation in order to have it covered under the warranty! COMPARE COLOR OF UNIT WITH OTHER FIXTURES.
READ AND FOLLOW ALL INSTRUCTIONS 1. DANGER: To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times. 6. A green colored terminal (or a wire connector marked `G’, `GR’, `GROUND’, or `GROUNDING’) is provided within the terminal compartment. To reduce the risk of electrical shock.
GENERAL NOTES CONSTRUCTION The tub surface is made of Lucite XL® Acrylic. The substructure is a composite laminate constructed of fire retardant fillers. WARNING: Failure to follow instructions exposes users to risk of electrical shock or fire. PLUMBING ROUGH-IN The bath waste pipe protrudes below the base approximately one inch. Provide supply pipe, rough-in waste and vent per local code. ELECTRICAL Factory wired for 110 Volt 20 Amps. Ground-Fault Circuit Interrupter (GFCI) is required.
INSTALLATION INSTALLING ONE-PIECE SKIRT CONTINUED PLUMBING ROUGH-IN The bath waste opening protrudes below the base approximately one inch. You may be required to cut a hole in the subfloor to accommodate bath waste. In slab on grade or prestressed concrete floors where cutting is not desired, the tub may be raised up by building the platform higher and using extra mortar under the tub. If a joist must be notched, verify that structure will not be weakened. Remove only what is necessary.
INSTALLATION CONTINUED Universal TOUCH PLUS START UP AND OPERATIONAL INSTRUCTIONS 4 3. 3 Use Button to decrease air jet speed while the blower is running. Press & hold to increase the blower speed, release pressure at the desired speed. Use Button to increase air jet speed while the blower is running. Press & hold to lower the blower speed, release pressure at the desired speed. Blower On/Off: 1st Press-the blower starts. 2nd Press-the blower stops. 2 4. 1 5 1. 2. 5.
INSTALLATION CONTINUED TYPICAL INSTALLATIONS Make absolutely certain that access panels and/or service openings are properly placed and that all possible areas where service may be required are accessible.
INSTALLATION CONTINUED CENTER ACCESS SKIRT Custom fitted skirt ensembles are available to provide the perfect finish for your bath and bathroom. All five (5) foot and six (6) foot rectangular models can be fitted with a one or two piece (center access) removable front skirt. Removable panel held in place by strong magnets attached to tub and tub panel and is easily detached for interior tub access. MAGNET AIR TUB CONTROLS START UP AND OPERATIONAL INSTRUCTIONS 3. 4 1. 2.
INSTALLATION CONTINUED Air Button Control-Whirlpool or Optional Combo Air Controls Star Jet Builder’s Jet Safety Suction Air Control/Turbo Boost™ Allows user to adjust the pressure from the jets With our pneumatic controls, you can select your bathtub’s pump with one finger. Allows user to adjust the direction pressure, by timing clock wise open flow, counter clockwise close flow. Constant flowing jet without on/off flow.
INSTALLATION CONTINUED H.E.E.T. Maintains water temperature without a heater using kinetic energy of the water pump. Chromatherapy Universal Touch E-Z Clean™ Aromatherapy O3 OZone™ Specially designed underwater LED lights will enhance your mood upon illumination. This 3-in-1 switch allows the user to turn the pump on and off. It has a 15 minute timer, and an automatic low water sensor that shuts down the pump in a low water level condition.
USER MAINTENANCE USER SHOULD periodically flush operating system (not to exceed 90 days). As a minimum, shall consist of filling and running system and draining. Universal Tubs recommends flushing with a mild solution of water and sanitizer such as chlorine or other commercially available whirlpool bath flushing products. DO NOT use abrasives. They may dull or scratch surface of the acrylic. DO NOT use oil based solvents. Clean with only a damp cloth or mild detergent or any common glass cleaner.
LIMITED WARRANTY COVERAGE READ CAREFULLY, THE WARRANTY APPLIES ONLY TO ORIGINAL OWNER 10 YEARS STRUCTURAL right to inspect the malfunction or defect on location. BATH SHELL: Universal Tubs warrants its bath shells against loss of water through the fiberglass laminate of the tub body as a result of a defect in materials and workmanship, for a period of ten (10) years from the purchase date.
NOTES 12
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLER: SAVE INSTALLATION INSTRUCTIONS WITH HOMEOWNER HOMEOWNER: KEEP INSTALLATION INSTRUCTIONS FOR FUTURE REFERENCE Please leave owner’s manual with warranty. If you have any problems or questions during installation, please call technical service at 877-360-4454 Record the numbers here for handy reference: Model No. Serial No. Date of Purchase M a de in USA Manufactured by Universal Tubs Spa World Corp.
