Warranty

FUEL LINE KIT
AC04124
Fits many RYOBI, HOMELITE, WEED EATER, POULAN, POULAN
PRO, TROY BILT, BOLENS and ARIENS hand-held products.
WARNING:
To reduce the risk of injury, user must read and understand
the operator’s manual for their tool and this instruction sheet.
Always wear eye protection with side shields marked to comply
with ANSI Z87.1. Ensure compatibility and fit before using this
accessory. Do not use this accessory if a part is damaged
or missing. If you are not comfortable performing any of the
functions described in these instructions, take your unit to an
authorized service center.
WARNING:
Before installing the new fuel lines, shut off engine, wait for all
moving parts to stop, allow engine to cool, drain any remaining
fuel from tank into approved fuel container, press the primer bulb
several times to remove any remaining fuel, then disconnect
spark plug wire and move it away from spark plug. Failure to
follow these instructions can result in serious personal injury or
property damage.
CALIFORNIA PROPOSITION 65
WARNING:
May contain chemicals known to California to cause cancer,
birth defects, or other reproductive harm.
WARNING:
Always refer to the replacement parts list provided by the
manufacturer of your tool to determine the correct diameter
and length of the fuel lines needed for your tool. Failure to use
the correct fuel lines for your specific tool could cause a fuel
leak that can result in a fire and possible serious personal injury.
PACKING LIST:
18 in. green fuel line (9/64 in. OD x 5/64 in. ID)
Fits many WEED EATER, POULAN and POULAN PRO tools.
18 in. white fuel line (1/8 in. OD x 1/16 in. ID)
18 in. blue fuel line (3/16 in. OD x 3/32 in. ID)
Fits many WEED EATER, POULAN, POULAN PRO, TROY BILT, BOLENS and
ARIENS tools.
7 in. clear fuel line (13/64 in. OD x 3/32 in. ID)
Fits many HOMELITE and RYOBI tools.
10.5 in. clear fuel line (13/64 in. OD x 3/32 in. ID)
Fits many HOMELITE and RYOBI tools.
Removal/installation tool
INSTALLING NEW RETURN AND SUPPLY
FUEL LINES
See Figures 1 - 3.
To determine the length and diameter of the fuel lines needed for
your tool, refer to the replacement parts list provided by the tool’s
manufacturer.
Place the unit with the supply and return fuel lines facing you
as shown. For better access and visibility, it may be neccesary
to remove the air box cover.
NOTE: Refer to the Operator’s Manual for your string trimmer
or power head for instructions on airbox cover removal.
For most models, the line on the bottom of the carburetor with
the filter attached is the supply fuel line. The fuel line coming
from the top of the carburetor is the return line.
NOTE: Replace supply and return fuel lines with the correct sized
replacement line.
To remove the old supply line/filter OR old return line:
Remove the fuel cap.
Detach the fuel line where it connects to the carburetor. Using
caution to not damage the fuel tank, cut old fuel line as close
as possible to the fuel tank. With a blunt instrument, push the
remaining cut fuel line into the fuel tank.
Pull the return line or the supply line/filter out of the tank.
NOTE: It may be helpful to use a tool such as the removal/
installation tool or needle nose pliers to pull the old supply fuel
line/filter to the outside of the tank.
To install the new supply line/filter:
Soak new supply line in warm water until it softens. Dry supply
line completely before use.
Carefully remove the fuel filter from the old supply line and install
it onto the end of the new supply line.
Gently stretch the new supply line.
Thread the removal/ installation tool into the fuel line holes at
top of the tank and out of the fuel cap opening. Hook the end
of the tool into the hole on the tapered end of the new fuel line.
Pull the tool, with the fuel line attached, slowly and firmly through
the tank and up through the hole.
Trim the fuel line to the proper length. Before trimming, make
sure the filter will rest in the lowest point of the fuel tank.
Install the fuel line securely onto the bottom (lower) connection
on the carburetor.
To install the new return line:
Thread the removal/installation tool into the fuel line holes at top
of the tank and out of the fuel cap opening. Hook the end of the
tool into the hole on the tapered end of the return line. Pull the
tool, with the fuel line attached, through the tank and up through
the hole.
Trim the return line to the proper length. The line should extend
1/2 in. inside the tank.
Install the return line securely onto the top (upper) connection
on the carburetor.
Securely replace fuel cap.
Reattach the spark plug wire.
WARNING:
Check for fuel leaks after completing installation of fuel line. Any
part that is leaking fuel is a fire hazard and must be replaced or
reinstalled immediately. If you find any leaks, correct the problem
before using the product. Failure to do so could result in a fire
that could cause serious personal injury.
A - Fuel cap (bouchon de carburant, tapa del tanque)
B - Fuel filter (filtre de carburant, filtro de combustible)
C - Fuel tank (réservoir de carburant, tanque de combustible)
D - Supply fuel line (conduit à essence d’alimentation, conducto de
suministro de combustible)
E - Return fuel line (conduit à essence de retour, conducto de retorno de
combustible)
A
C
B
D
E
COUPER LE CONDUIT À ESSENCE USÉ ICI
CORTE LAS LÍNEAS DE COMBUSTIBLE USADAS EN ESTE LUGAR
CUT OLD
FUEL LINES
HERE
Fig. 1
A - Filter (filtre, filtro)
B - Supply line (flexibles de carburant, conductos de combustible)
C - Removal/installation tool (outil de retrait et d’installation, herramienta
de instalación o desinstalación)
Fig. 2
Fig. 3
C
B
A
A - Return fuel line (conduit à essence de retour, conducto de retorno de
combustible)
A
990000384
12-4-12 (REV:01)