R-320 Operator’s Manual Serial #
WARRANTY UniVersal Labeling Systems, Inc. warranties all parts to be free from defects in material and workmanship for a period of one year from the date of shipment from our facility. This guarantee is based upon equipment being used 8 hours per day, or 40 hours per week, or in any increment which does not total more than a single shift operation, or 2,080 hours per year. Warranty will be reduced proportionally.
Warranty Assembly and Operation Drawings Layout, Main Exploded View (conveyor) Exploded view BASE Conveyor Assembly, Applicator Crank Micro Adjustor Sensor Mounting Bracket SBK Wipe Down WPD-500 R320 Elect.
MODEL R-320 ASSEMBLY AND OPERATING INSTRUCTIONS Conveyor Height can be adjusted from your system’s specified height by adjusting the leveling pads RE-TIGHTEN LOCKING BOLT AND ANGULAR BRACE, BEFORE REMOVING SUPPORT AT BOTH ENDS OF CONVEYOR. FAILURE TO RE-TIGHTEN THE LOCKING SCREW ON SLIDING SLEEVE COULD RESULT IN THE CONVEYOR AND ATTACHMENTS DROPPING, CAUSING SERIOUS DAMAGE TO THE SYSTEM. SEE APPLIER INSTRUCTION MANUAL FOR PROPER OPERATION OF APPLIER HEAD AND WEBBING.
MODEL R-320 ASSEMBLY AND OPERATING INSTRUCTIONS 8. Stop conveyor by turning speed control to “O”. Turn off turning unit. Plug power cord of applier into control box on front of conveyor. (NOTE: Applier and turning unit will not receive power with switch on control box on front of conveyor in OFF position). 9. Raise or lower applier so that label is centered on container. Label web must always run to lower edge of peeler bar on this system, with edge of peeler bar clearing top of conveyor EDGE.
MODEL R-320 ASSEMBLY AND OPERATING INSTRUCTIONS IT IS EXTREMELY IMPORTANT THAT SPEEDS OF LABEL DELIVERY AND PRODUCT BE MATCHED FOR SATISFACTORY PLACEMENT AND WIPE DOWN OF LABEL. If label is tending to walk up or down on container, label applier may be rotated to position peeler bar in parallel with container, so that label is started on container accurately, by loosening large hex nut on swiveling bracket that applier is secured to and located on sliding sleeve on post.
SUGGESTED SPEED SETTING As tested at the factory, the following are suggested setting of speeds and time delays: DIAL SETTING * Conveyor Speed _______________ * Turning Unit _______________ * Applier _______________ Product Spacer _______________ These settings will product approximately parts per minute production _______________ If speed of any of the above “*” are changed for any reason, comparable changes in the other settings should be made.
When machine is received, open carton carefully and remove machine by placing hands under machine base for lifting. Place machine on flat surface for installation of label roll holder to machine. (NOTE: Acorn nuts and hex nuts to be removed). Slide label reel over the two threaded studs, secure with hex nuts, then install the two acorn nuts. Machine is not ready for installation and can be secured to an appropriately fabricated bars, flatplate, etc.
R320 AUTOMATIC SYSTEM WITH L15H APPLICATOR RECOMMENDED SPARE PARTS PART # 200109 200198 420173 L-129-S L-137-H L-140-F-3 L-175-1 L-143 L-176-1 200160 300013 300023 600008 600007 TA-215 TA-415 500030 L-132 LP-100-S-1-X 410000 L-128-C L-105-RA L-105-LA 600300 200046 500085 PART DESCRIPTION MICRO SWITCH, LABEL SENSING POWER MODULE STARWHEEL SPRING STARWHEEL, LABEL SENSING DRIVE ROLLER (HD) SLIP CLUTCH COLLAR (REPLACES L-140-F-2) ASSY.
TA-2/4 ID# 1 2 3 4 5 ** 7 8 9 10 11 15 16 ** 17 ** 18 19 20 21 ** 22 ** 23 ** 24 ** 25 26 27 ** 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 2 & 4 INCH TURNING UNITS Bill of Material PART# 300022 400016 410000 410001 600007 600008 TA-2-202 TA-2-203 TA-2-205 TA-2-205-A TA-2-205-B TA-2-219-1 TA-2-201 TA-4-401 TA-2-217 TA-4-403 TA-4-406-1 TA-4-406-1 TA-4-407 TA-2-206-A TA-4-408A TA-2-206-B TA-4-408B TA-2-204-A TA-4-409A TA-2-204-B TA-4-409B TA-4-413-1 TA-4-412 TA-2-218 TA-4-418 L-172-04 L-172-03 OR L-172-
TA-2/4 ID# 44 45 46 47 48 49 50 51 52 N/S PART# TA-2-215B SS-112 TA-2-215A FLOOR STOCK FLOOR STOCK FLOOR STOCK FLOOR STOCK 200026 TB-1 300023 2 & 4 INCH TURNING UNITS Bill of Material QTY 4 2 2 2 11 4 4 1 1 2 DESCRIPTION GUIDE, BACK PLATE KNOB, MICROMETER ADJ. PLATE, TURN-AROUND MOUNT BOLT, 3/8 x 2-1/4 H.H.M.S WASHER, #10 x .06 THK. WASHER, 1/4” x .06 THK.
