FOREWORD READ FIRST—THEN DRIVE SAFELY Welcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. Before driving your vehicle please read this Owner’s Manual carefully. This will ensure familiarity with controls and maintenance requirements, assisting you in the safe operation of your vehicle.
WHEN READING THE MANUAL MODIFICATION OF YOUR VEHICLE This vehicle should not be modified. Modification could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from modifications may not be covered under NISSAN warranties. This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle.
CALIFORNIA PROPOSITION 65 WARNING WARNING Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
NISSAN CUSTOMER CARE PROGRAM NISSAN CARES . . . Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Your NISSAN dealer is always available to assist you with all your automobile sales and service needs.
Table of Contents Illustrated table of contents 0 Safety—Seats, seat belts and supplemental restraint system 1 Instruments and controls 2 Pre-driving checks and adjustments 3 Heater, air conditioner, audio and phone systems 4 Starting and driving 5 In case of emergency 6 Appearance and care 7 Maintenance and do-it-yourself 8 Technical and consumer information 9 Index 10
Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X
0 Illustrated table of contents Airbags, seat belts and child restraints . . . . . . . . . . . . . . . 0-2 Exterior front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-3 Exterior rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-4 Passenger compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-5 Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-6 Engine compartment check locations . . . .
AIRBAGS, SEAT BELTS AND CHILD RESTRAINTS 1. 2. 2nd row seat belts (P. 1-11) Roof-mounted curtain side-impact and rollover supplemental air bags (if so equipped) (P. 1-51) 3. Front seat belts (P. 1-11) 4. Front-seat Active Head Restraints (P.1-6) 5. Supplemental front-impact air bags (P.1-59) 6. Seats (P. 1-2) 7. Occupant classification sensor (pressure sensor) (P. 1-59) 8. Seat belts with pretensioners (P. 1-64) 9. Front seat-mounted side-impact supplemental air bags (if so equipped) (P. 1-51) 10.
EXTERIOR FRONT 1. 2. Engine hood (P. 8-6) Windshield wiper and washer switch (P. 2-23) 3. Windshield (P. 8-22) 4. Windows (P. 2-43) 5. Door locks, keyfob, keys (P. 3-3, 3-6, 3-2) 6. Mirrors (P. 3-12) 7. Tire pressure (P. 8-33) 8. Flat tire (P. 6-3) 9. Tire chains (P. 8-40) 10. Headlight and turn signal switch (P. 2-25); Replacing bulbs (P. 8-28) 11. Fog light switch (if so equipped) (P. 2-28) See the page number indicated in parentheses for operating details.
EXTERIOR REAR 1. 2. 3. 4. 5. Rear sliding window (if so equipped) (P.2-46) Vehicle loading (P. 9-12) Truck box, tailgate (P.3-15) Replacing bulbs (P. 8-28) Fuel-filler cap, fuel recommendation (P. 3-10, P. 9-3) See the page number indicated in parentheses for operating details.
PASSENGER COMPARTMENT 1. 2. 3. 4. 5. 6. Map lights (P. 2-47) Sun visors (P. 3-11) Inside mirror (P. 3-12) Vents (P. 4-2) Glove box (P. 2-38) Shift knob (automatic transmission, if so equipped) (P. 5-12) 7. Cup holders (P. 2-40) 8. Front seats (P. 1-2) 9. Console box (P. 2-38) 10. Rear seats (P. 1-10) 11. Flat tire/Jacking equipment storage (P. 6-3) See the page number indicated in parentheses for operating details.
INSTRUMENT PANEL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. WIC1326 Vents (P. 4-2) Headlight/fog light (if so equipped)/turn signal switch (P. 2-25) Steering wheel switch for audio control (if so equipped)/BluetoothT HandsFree Phone System (if so equipped) (P. 4-26, P. 4-27) Driver supplemental air bag/horn (P. 1-51, P. 2-29) Meters, gauges and warning/indicator lights (P. 2-3, 2-12) Cruise control main/set switches (if so equipped) (P. 5-19) Windshield wiper/washer switch (P. 2-23) Storage (P.
14. 15. 16. 17. 18. 19. 20. 21. 22. 23. Heated seat switches (if so equipped) (P. 2-30) Hill descent control switch (if so equipped) (P. 2-31) Vehicle Dynamic Control (VDC) OFF switch (if so equipped) (P. 2-31) Shift selector lever (P. 5-12) 4WD shift switch (if so equipped) (P. 5-21) Climate controls (P. 4-2) Passenger air bag status light (P. 1-60) Hazard warning flasher switch (P. 2-29) Ignition switch (P. 5-8) Tilt steering wheel control (if so equipped) (P. 3-11) Cargo lamp switch (P.
ENGINE COMPARTMENT CHECK LOCATIONS QR25DE engine 1. Windshield washer fluid reservoir (P. 8-15) 2. Fuse/fusible link box (P. 8-24) 3. Fuse and relay box (P. 8-24) 4. Air cleaner (P. 8-20) 5. Engine oil filler cap (P. 8-9) 6. Engine oil dipstick (P. 8-9) 7. Brake fluid reservoir/Clutch fluid reservoir (M/T model) (P. 8-14) 8. Drive belt location (P.8-18) 9. Radiator cap (P. 8-8) 10. Power steering fluid reservoir (P. 8-13) 11. Battery (P. 8-15) 12. Engine coolant reservoir (P.
VQ40DE engine 1. Windshield washer fluid reservoir (P. 8-15) 2. Battery (P. 8-15) 3. Fuse and relay box (P. 8-24) 4. Fuse/fusible link box (P. 8-24) 5. Engine oil filler cap (P. 8-9) 6. Engine oil dipstick (P. 8-9) 7. Brake fluid reservoir (P. 8-14) 8. Air cleaner (P. 8-20) 9. Drive belt location (P.8-18) 10. Radiator cap (P. 8-8) 11. Power steering fluid reservoir (P. 8-13) 12. Engine coolant reservoir (P. 8-8) See the page number indicated in parentheses for operating details.
WARNING/INDICATOR LIGHTS Warning light or Name Page Anti-lock Braking System (ABS) warning light 2-13 Automatic transmission oil temperature warning light (if so equipped) 2-13 Automatic transmission park warning light ( model) 2-13 Brake warning light 2-13 or Charge warning light (if so equipped) 2-14 Door open warning light 2-14 Warning light Name Page Indicator light Name Page Engine oil pressure warning light (if so equipped) 2-14 Automatic transmission position indicator light
Indicator light Name Page High beam indicator light (Blue) 2-18 Hill Descent Control indicator light (if so equipped) 2-31 Malfunction indicator lamp (MIL) 2-18 Overdrive off indicator light (automatic transmission only) 2-19 Security indicator light (if so equipped) 2-19 Slip indicator light for models with ABLS (if so equipped) 2-19 Slip indicator light for models with VDC (if so equipped) 2-19 Indicator light Name Page Transfer 4LO position indicator light ( model) 2-20 Turn signal/
MEMO 0-12 Illustrated table of contents
1 Safety—Seats, seat belts and supplemental restraint system Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front manual seat adjustment (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front power seat adjustment (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Jump seat (King cab) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Head restraint adjustment . . . . . . . . . . .
SEATS FRONT MANUAL SEAT ADJUSTMENT (if so equipped) ARS1152 WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries. ● For the most effective protection when the vehicle is in motion, the seat should be upright.
WRS0175 WRS0176 Forward and backward Reclining Pull the lever up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. To recline the seatback, pull the lever up and lean back. To bring the seatback forward, pull the lever up and lean your body forward. Release the lever to lock the seatback in position.
The reclining feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit (see “Precautions on seat belt usage” later in this section). Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the transmission is in P (Park). WRS0163 FRONT POWER SEAT ADJUSTMENT (if so equipped) Operating tips ● The power seat motor has an auto-reset overload protection circuit.
WRS0164 Seat lifter (driver’s seat) Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion. WRS0389 Lumbar support (if so equipped for driver’s seat) The lumbar support feature provides lower back support to the driver. Move the lever forward or backward to adjust the seat lumbar area. LRS0556 JUMP SEAT (King cab) WARNING ● Do not use a child restraint in the driver’s side jump seat. This seating position is not suitable for child restraint installation.
WRS0213 HEAD RESTRAINT ADJUSTMENT 2 . To lower, To raise the head restraint, pull it up s 1 and push the push and hold the lock knob s 2 . head restraint down s WRS0134 Adjust the head restraint so the center is level with the center of your ears. The head restraints on the rear seats are removable. WARNING Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Do not remove them. Check the adjustment after someone else uses the seat.
● Do not attach anything to the head restraint stalks. Doing so could impair Active Head Restraint function. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly. The Active Head Restraint moves forward utilizing the force that the seatback receives from the occupant in a rear-end collision.
● Properly secure all cargo to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. LRS0608 Folding the front passenger’s seatback (if so equipped) To fold the front passenger’s seatback flat for extra storage length when transporting long items: 1 s Slide the seat to the rearmost position.
WARNING ● If you fold the front passenger’s seatback flat forward to carry longer objects, be sure this cargo is properly secured and not near an air bag. In a crash, an inflating air bag might force that object toward a person. This could cause severe injury or even death. Secure objects away from the area in which an air bag would inflate. See “Precautions on supplemental restraint system” later in this section.
WARNING ● When the vehicle is being used to carry cargo, properly secure all cargo to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. LRS0567 s 3 Repeat this process to raise and secure the seat cushion on the other side of the vehicle for maximum storage capacity. To return the rear bench seat to a seating position reverse the process.
SEAT BELTS WARNING Never allow anyone to ride in the cargo area or on the rear seat when it is in the fold-down position. Use of these areas by passengers without proper restraints could result in serious injury in an accident or sudden stop.
SSS0134 WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly restrained in the rear seat and, if appropriate, in a child restraint. SSS0016 WARNING ● The seat belt should be properly adjusted to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident. Serious injury or death can occur if the seat belt is not worn properly.
● Be sure the seat belt tongue is securely fastened to the proper buckle. ● Do not wear the seat belt inside out or twisted. Doing so may reduce its effectiveness. ● Do not allow more than one person to use the same seat belt. ● Never carry more people in the vehicle than there are seat belts. SSS0014 WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck.
There are three basic types of child restraint systems: ● Rear facing child restraint ● Front facing child restraint ● Booster seat The proper restraint depends on the child’s size. Generally, infants up to about 1 year and less than 20 pounds (9 kg) should be placed in rear facing child restraints. Front facing child restraints are available for children who outgrow rear facing child restraints and are at least one year old.
kg) and 80 lbs (36 kg). A booster seat should be used to obtain proper seat belt fit. NISSAN recommends that a child be placed in a commercially available booster seat if the shoulder belt in the child’s seating position fits close to the face or neck or if the lap portion of the seat belt goes across the abdomen. The booster seat should raise the child so that the shoulder belt is properly positioned across the top, middle portion of the shoulder and the lap belt is low on the hips.
WRS0174 Manual front seat shown Fastening the seat belts (Front seats all models and rear seats Crew cab models) 1 s Adjust the seat. See “Seats” earlier in this section. LRS0594 s 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage. ● The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat.
The Emergency Locking Retractor (ELR) mode allows the seat belt to extend and retract to allow the driver and passengers some freedom of movement in the seat. The ELR locks the seat belt when the vehicle slows down rapidly or during certain impacts. The Automatic Locking Retractor (ALR) mode (child restraint mode) locks the seat belt for child restraint installation.
movement in the seat. The ELR locks the seat belt when the vehicle slows down rapidly or during certain impacts. The Automatic Locking Retractor (ALR) mode (child restraint mode) locks the seat belt for child restraint installation. When the ALR mode is activated, the seat belt cannot be extended again until the seat belt tongue is detached from the buckle and fully retracted. The seat belt returns to the ELR mode after the seat belt fully retracts.
To increase your confidence in the seat belts, check the operation as follows. ● Grasp the shoulder belt and pull forward quickly. The retractor should lock and restrict further belt movement. If the retractor does not lock during this check or if you have any questions about seat belt operation, see a NISSAN dealer. WRS0139 Unfastening the seat belts s 1 To unfasten the seat belt, press the button on the buckle. The seat belt automatically retracts.
WARNING WARNING ● After adjustment, release the adjustment button and try to move the shoulder belt anchor up and down to make sure it is securely fixed in position. ● Only NISSAN seat belt extenders, made by the same company which made the original equipment seat belts, should be used with NISSAN seat belts. ● The shoulder belt anchor height should be adjusted to the position best for you.
CHILD RESTRAINTS ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An inflating front air bag could seriously injure or kill your child. A rear-facing child restraint must only be used in the rear seat. ARS1098 PRECAUTIONS ON CHILD RESTRAINTS WRS0256 WARNING ● Infants and small children should always be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint can result in serious injury or death.
● If the child restraint is not anchored properly, the risk of a child being injured in a collision or a sudden stop greatly increases. ● Child restraint anchor points are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts or harnesses. ● Adjustable seatbacks should be positioned to fit the child restraint, but as upright as possible.
LRS0429 LATCH system anchor locations LATCH (Lower Anchors and Tethers for CHildren) SYSTEM Your vehicle is equipped with special anchor points that are used with LATCH (Lower Anchors and Tethers for CHildren) system compatible child restraints. The LATCH anchor points are provided to install child restraints in the rear outboard seating positions only (Crew cab models only). Do not attempt to install a child restraint in the center position using the LATCH anchors.
TOP TETHER STRAP CHILD RESTRAINT If the manufacturer of your child restraint requires the use of a top tether strap, it must be secured to the anchor point. WARNING LRS0661 LATCH webbing-mounted attachment Installing child restraint LATCH anchor attachments LATCH compatible child restraints include two rigid or webbing-mounted attachments that can be connected to two anchors located at certain seating positions in your vehicle.
Top Tether Anchor Point Locations 4. Tighten the tether strap according to the manufacturer’s instructions to remove any slack. Anchor points are located in the following locations: For best child restraint fit, see the child restraint installation instructions in this section and the child restraint manufacturer’s instructions. ● On the back of the front passenger seat (King cab only). ● On the floor between the jump seat belt buckles in the center of the vehicle (King cab only).
1. Pull the cover plate off to access the top tether strap routing bracket for the passenger’s side jump seat. 2. Route the top tether strap through the routing bracket. 3. Then pull the top tether strap tight and secure it to the top tether anchor bracket located between the seat belt buckle receivers in the center of the vehicle. LRS0551 Passenger’s side jump seat (King cab models) 1. Cover plate LRS0561 Installing top tether strap 1. Top tether strap 2. Top tether strap routing bracket 2.
LRS0392 LRS0393 Rear bench seat (Crew cab models only) The anchor points are located under the rear window behind the rear bench seat. If you have any questions when installing a top strap child restraint on the rear seat, consult your NISSAN dealer for details. Anchor point access 1. Pull strap 2. Anchor point location To access the anchor points behind the rear bench seat, tilt the rear seatback forward by lifting up on the pull strap behind the seatback. LRS0576 Installing top tether strap 1.
4. Tighten the tether strap according to the manufacturer’s instructions to remove any slack. For best child restraint fit, see the child restraint installation instructions in this section and the child restraint manufacturer’s instructions. CHILD RESTRAINT INSTALLATION USING LATCH WARNING ● Attach LATCH compatible child restraints only at the locations shown. For the LATCH lower anchor locations, see “Lower Anchors and Tethers for CHildren System (LATCH)” in this section.
LRS0664 Front facing rigid-mounted – step 2 If necessary, adjust or remove the head restraint to obtain the correct child restraint fit. See “Head restraint adjustment” in this section. If the head restraint is removed, store it in a secure place. Be sure to install the head restraint when the child restraint is removed. If the seating position does not have an adjustable head restraint and it is interfering with the proper child restraint fit, try another seating position or a different child restraint.
7. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 3 through 6. Rear-facing Follow these steps to install a rear-facing child restraint using LATCH System: 1. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions. LRS0665 Rear facing web-mounted – step 2 2. Secure the child restraint anchor attachments to the LATCH lower anchors.
5. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 2 through 4. LRS0673 Rear facing – step 3 3. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attachments. Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.
● NISSAN recommends that child restraints be installed in the rear seat. However, if you must install a forward facing child restraint in the front passenger seat, move the passenger seat to the rearmost position. Also, be sure the front passenger air bag status light is illuminated to indicate the passenger air bag is OFF. See “Front passenger air bag and status light” later in this section for details.
2. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions The back of the child restraint should be secured against the vehicle seatback. If necessary, adjust or remove the head restraint to obtain the correct child restraint fit. See “Head restraint adjustment” in this section.
LRS0667 Front facing – step 4 4. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to the Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted. LRS0668 Front facing – step 5 5. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0681 Front facing – step 6 6.
8. Before placing the child in the child restraint, hold the child restraint near the seat belt path and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the shoulder belt to further tighten the child restraint.
WRS0256 Rear-facing – step 1 Rear-facing Follow these steps to install a rear-facing child restraint using the vehicle seat belt in the rear bench seat (Crew cab models only): WRS0761 Rear facing – step 2 2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing. 1.
LRS0670 Rear facing – step 4 4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0762 Rear facing – step 5 5. Remove any additional slack from the child restraint; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seatback while pulling up on the seat belt. WRS0763 Rear facing – step 6 6.
7. Check that the retractor is in the ALR mode by trying to pull more seat belt out of the retractor. If you cannot pull any more seat belt webbing out of the retractor, the retractor is in the ALR mode. 8. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 7. After the child restraint is removed and the seat belt fully retracted, the ALR mode (child restraint mode) is canceled.
If the head restraint is removed, store it in a secure place. Be sure to install the head restraint when the child restraint is removed. If the seating position does not have an adjustable head restraint and it is interfering with the proper child restraint fit, try another seating position or a different child restraint. LRS0537 LRS0540 Front facing (passenger’s side seating position only) — step 2 2. Position the child restraint on the seat.
LRS0541 Front Facing — step 3 3. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing. LRS0542 Front Facing — step 4 4. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode).
8. Before placing the child in the child restraint, hold the child restraint near the seat belt path and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25 mm). If it does move more than 1 inch (25 mm), pull again on the shoulder belt to further tighten the child restraint.
LRS0597 Rear facing LRS0549 WARNING WARNING ● Do not install a child restraint system on the passenger’s side jump seat without unfolding the seat extender. A child restraint system will not be installed properly and the child could be seriously injured or killed in a sudden stop or collision. ● To install a rear facing child restraint on the passenger’s side jump seat, it will be necessary to move the front passenger’s seat fully forward and place the front seatback upright or tilt it forward.
LRS0537 LRS0544 Rear Facing (passenger’s side jump seat only) — step 2 2. Move the front passenger’s seat into the FULL FORWARD position. Then move the front seatback to the upright or tilted forward position. Position the child restraint on the jump seat. The direction of the child restraint depends on the type of the child restraint and the size of the child. Always follow the restraint manufacturer’s instructions. LRS0545 Rear Facing — step 3 3.
LRS0546 Rear Facing — step 4 4. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to the Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted. LRS0547 Rear Facing — step 5 5. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.
BOOSTER SEATS 7. Before placing the child in the child restraint, hold the child restraint near the seat belt path and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25 mm). If it does move more than 1 inch (25 mm), pull again on the shoulder belt to further tighten the child restraint.
● Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself. ● NISSAN recommends that the booster seat be installed in the rear seat. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat.
LRS0455 LRS0453 LRS0464 Booster seats of various sizes are offered by several manufacturers. When selecting any booster seat, keep the following points in mind: ● Make sure the child’s head will be properly supported by the booster seat or vehicle seat. The seat back must be at or above the center of the child’s ears. For example, if a 1 is chosen, the low back booster seat s vehicle seat back must be at or above the center of the child’s ears.
BOOSTER SEAT INSTALLATION ON FRONT PASSENGER SEAT AND REAR SEAT (Crew cab models only) WARNING NISSAN recommends that booster seats be installed in the rear seat. However, if you must install a booster seat in the front passenger seat, move the passenger’s seat to the rearmost position. CAUTION Do not use the lap/shoulder belt Automatic Locking Retractor mode when using a booster seat with the seat belts.
4. Position the lap portion of the seat belt low and snug on the child’s hips. Be sure to follow the booster seat manufacturer’s instructions for adjusting the belt routing. 5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack. Be sure the shoulder belt is positioned across the top, middle portion of the child’s shoulder. Be sure to follow the booster seat manufacturer’s instructions for adjusting the belt routing. LRS0563 Rear outboard position 3.
BOOSTER SEAT INSTALLATION ON PASSENGER’S SIDE JUMP SEAT ONLY (King cab models only) WARNING ● When installing a booster seat in the passenger’s side jump seat position be sure to unfold the seat extension on the jump seat. If the jump seat extension is not properly used, the booster seat will not be installed correctly and a child could be injured in a collision or sudden stop. ● Never install a booster seat on the driver’s side jump seat.
SUPPLEMENTAL RESTRAINT SYSTEM 3. The booster seat should be positioned on the vehicle seat so that it is stable. If necessary, adjust or remove the head restraint to obtain the correct booster seat fit. See “Head restraint adjustment” earlier in this section. If the head restraint is removed, store it in a secure place. Be sure to install the head restraint when the booster seat is removed.
Roof-mounted curtain side-impact and rollover supplemental air bag system (if so equipped): This system can help cushion the impact force to the head of occupants in front and rear outboard seating positions in certain side impact or rollover collisions. In a side impact, the curtain and rollover air bags are designed to inflate on the side where the vehicle is impacted. In a rollover, both curtain and rollover air bags are designed to inflate and remain inflated for a short time.
● The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened. The Advanced Air Bag System monitors the severity of a collision and seat belt usage then inflates the air bags. Failure to properly wear seat belts can increase the risk or severity of injury in an accident. ● The front passenger seat is equipped with an occupant classification sensor (pressure sensor) that turns the front passenger air bag OFF under some conditions.
ARS1041 WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations. ARS1042 ARS1043 WARNING ● Children may be severely injured or killed when the front air bags, side air bags or curtain and rollover air bags inflate if they are not properly restrained. Pre-teens and children should be properly restrained in the rear seat, if possible.
ARS1044 ARS1045 WRS0256 WARNING ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An inflating front air bag could seriously injure or kill your child. See “Child restraints” earlier in this section for details.
WRS0431 Do not lean against the door. LRS0396 Do not lean against doors or windows. SSS0162 Do not lean against doors or windows. WARNING Front seat-mounted side-impact supplemental air bags (if so equipped) and roofmounted curtain side-impact and rollover supplemental air bags (if so equipped): ● The side air bags and curtain and rollover air bags ordinarily will not inflate in the event of a frontal impact, rear impact, or lower severity side collision.
WARNING ● The seat belts, the side air bags and curtain and rollover air bags are most effective when you are sitting well back and upright in the seat. The side air bag and curtain and rollover air bag inflate with great force. Do not allow anyone to place their hand, leg or face near the side air bag on the side of the seatback of the front seat or near the side roof rails.
1. Roof-mounted curtain side-impact and rollover supplemental air bag inflators (if so equipped) 2. Roof-mounted curtain side-impact and rollover supplemental air bags (if so equipped) 3. Air bag Control Unit (ACU) 4. Supplemental front-impact air bag modules 5. Crash zone sensor 6. Occupant classification system control unit 7. Occupant classification sensor (pressure sensor) 8. Satellite sensors 9. Seat belt buckle switches 10. Seat belt with pretensioner 11.
NISSAN Advanced Air Bag System (front seats) This vehicle is equipped with the NISSAN Advanced Air Bag System for the driver and front passenger seats. This system is designed to meet certification requirements under U.S. regulations. It is also permitted in Canada. However, all of the information, cautions and warnings in this manual still apply and must be followed. The driver supplemental front-impact air bag is located in the center of the steering wheel.
Status light is The front passenger air bag status light located near the climate controls. The light operates as follows: ● Unoccupied passenger’s seat: The is OFF and the front passenger air bag is OFF and will not inflate in a crash. ● Passenger’s seat occupied by a small adult, child or child restraint as outlined in this illuminates to indicate section: The that the front passenger air bag is OFF and will not inflate in a crash.
Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause the passenger air bag to be automatically turned OFF. For small adults it may be turned OFF, however if the occupant takes his/her weight off the seat cushion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position), this could cause the sensor to turn the air bag OFF.
Other supplemental front-impact air bag precautions WARNING ● Do not place any objects on the steering wheel pad or on the instrument panel. Also, do not place any objects between any occupant and the steering wheel or instrument panel. Such objects may become dangerous projectiles and cause injury if the front air bags inflate. ● Immediately after inflation, several front air bag system components will be hot. Do not touch them; you may severely burn yourself.
are designed to inflate in higher severity side collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity side impact. They are designed to inflate on the side where the vehicle is impacted. They may not inflate in certain side collisions. Curtain and rollover air bags are also designed to inflate in certain types of rollover collisions or near rollovers.
WARNING ● Do not place any objects near the seatback of the front seats. Also, do not place any objects (an umbrella, bag, etc.) between the front door finisher and the front seat. Such objects may become dangerous projectiles and cause injury if a side air bag inflates. ● Right after inflation, several side air bag and curtain and rollover air bag system components will be hot. Do not touch them; you may severely burn yourself.
● If you need to dispose of a pretensioner or scrap the vehicle, contact a NISSAN dealer. Correct pretensioner disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury. The pretensioner system activates in conjunction with the front air bag system. The pretensioner system also activates with curtain and rollover air bags in certain types of rollover collisions or near rollovers.
SUPPLEMENTAL AIR BAG WARNING LABELS When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational. Warning labels about the supplemental frontimpact air bag, front seat-mounted side-impact supplemental air bag and roof-mounted curtain side-impact and rollover supplemental air bag systems are placed in the vehicle as shown in the illustration.
WARNING If the supplemental air bag warning light is on, it could mean that the front air bag, side air bag, curtain and rollover air bag and/or pretensioner systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible Repair and replacement procedure The front air bags, side air bags, curtain and rollover air bags and pretensioners are designed to inflate on a one-time-only basis.
2 Instruments and controls Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Meters and gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . 2-4 Trip computer (if so equipped) . . . . . . . . . . . . . . . . . . . 2-5 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Engine coolant temperature gauge . . . . . . . . . . . . . . .
Under-seat storage bins. . . . . . . . . . . . . . . . . . . . . . . . 2-37 Console box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38 Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38 Sunglasses holder (if so equipped) . . . . . . . . . . . . . . 2-38 Map pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39 Seat pockets (if so equipped) . . . . . . . . . . . . . . . . . . . 2-40 Cup holders . . . . . . . . . . . . .
INSTRUMENT PANEL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. WIC1326 Vents (P. 4-2) Headlight/fog light (if so equipped)/turn signal switch (P. 2-25) Steering wheel switch for audio control (if so equipped)/BluetoothT HandsFree Phone System (if so equipped) (P. 4-26, P. 4-27) Driver supplemental air bag/horn (P. 1-51, P. 2-29) Meters, gauges and warning/indicator lights (P. 2-3, 2-12) Cruise control main/set switches (if so equipped) (P. 5-19) Windshield wiper/washer switch (P. 2-23) Storage (P.
METERS AND GAUGES 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. Heated seat switches (if so equipped) (P. 2-30) Hill descent control switch (if so equipped) (P. 2-31) Vehicle Dynamic Control (VDC) OFF switch (if so equipped) (P. 2-31) Shift selector lever (P. 5-12) 4WD shift switch (if so equipped) (P. 5-21) Climate controls (P. 4-2) Passenger air bag status light (P. 1-60) Hazard warning flasher switch (P. 2-29) Ignition switch (P. 5-8) Tilt steering wheel control (if so equipped) (P.
SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed. Odometer/Twin trip odometer The odometer/twin trip odometer is displayed when the ignition switch is in the ON position. The odometer records the total distance the vehicle has been driven. The twin trip odometer records the distance of individual trips. LIC0780 WIC0912 1. 2. 3.
TRIP COMPUTER (if so equipped) The display of the trip computer is situated in the speedometer display. When the ignition is turned to ON, the display scrolls all the modes of the trip computer and then shows the mode chosen before the ignition switch was turned OFF. ● If the amount of fuel added while the ignition switch is OFF is small, the display just before the ignition switch is turned OFF may continue to be displayed.
Journey time The journey time mode shows the time since the last reset. The displayed time can be reset by pressing the change button for more than approximately 1 second. Trip computer reset Pushing the change button for more than 3 seconds will reset all modes except Trip A and distance to empty (dte). LIC0738 TACHOMETER The tachometer indicates engine speed in revolutions per minute (rpm). Do not rev the engine 1 .
indicates that the fuel-filler door is The located on the driver’s side of the vehicle. CAUTION If the gauge indicates coolant temperature near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If the gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See “If your vehicle overheats” in the “In case of emergency” section for immediate action required.
CAUTION ● This gauge is not designed to indicate low engine oil level. Use the dipstick to check the oil level. (See “Engine oil” in the “Maintenance and do-it-yourself” section.) ● If the gauge needle does not move with the proper amount of engine oil, have the vehicle checked by a NISSAN dealer. Continued vehicle operation in such a condition could cause serious damage to the engine.
COMPASS AND OUTSIDE TEMPERATURE DISPLAY (if so equipped) ● When the outside temperature is between 140°F (60°C) and 194°F (90°C), the display will read 140°F (60°C). When the temperature is above 194°F (90°C), the display will read “SC”. This unit has the following functions: ● Measures terrestrial magnetism and indicates heading direction of vehicle ● Indicates outside air temperature ● When the outside temperature is between -40°F (-40°C) and -60°F (-51°C), the display will read -40°F (-40°C).
COMPASS DISPLAY Push the button for about 1 second when the ignition key is in the ON position to toggle the outside temperature and compass direction dis1 on or off. The display will indicate the play s direction of the vehicle’s heading. N: North E: East S: South W: West If the display reads “CAL”, calibrate the compass by driving the vehicle in three complete circles at less than 5 MPH (8 km/h). You can also calibrate the compass by driving your vehicle on your everyday route.
Zone variation change procedure The difference between magnetic north and geographical north is known as variance. In some areas, this difference can sometimes be great enough to cause false compass readings. Follow these instructions to set the variance for your particular location if this happens: 1. Press and hold the button for about 8 seconds. The current zone number will appear in the display. Release the button. 2. Find your current location on the zone map. Refer to the illustration. 3.
WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS or Anti-lock Braking System (ABS) warning light Low windshield washer fluid warning light Hill descent control indicator light (if so equipped) Automatic transmission oil temperature warning light (if so equipped) Seat belt warning light and chime Malfunction Indicator Light (MIL) Automatic transmission park warning light ( model) Supplemental air bag warning light Overdrive off indicator light (automatic transmission only) or Automatic transmission
CHECKING BULBS With all doors closed, apply the parking brake and turn the ignition key to the ON position without starting the engine. The following lights will come on: , or , , , , The following lights come on briefly and then go off: , or , , , , , , If any light fails to come on, it may indicate an open circuit in the electrical system. Have the system repaired promptly.
Parking brake indicator Low brake fluid warning light ● Pressing the brake pedal with the engine stopped and/or a low brake fluid level may increase your stopping distance and braking will require greater pedal effort as well as pedal travel. When the ignition key is in the ON position, the light warns of a low brake fluid level.
4WD warning light ( model) The 4WD warning light comes on when the key switch is turned to ON. It turns off soon after the engine is started. – in the 4LO position for manual transmission models, stop the vehicle and shift the transmission shift lever to the N position with the clutch pedal depressed and shift the 4WD shift switch to 2WD. If the engine or vehicle is not functioning properly, the warning light will either remain illuminated or blink.
placed in the ON position. The light will remain on after the 1 minute. Have the system checked by a NISSAN dealer. For additional information, see “Tire Pressure Monitoring System (TPMS)” in the “Starting and driving” section. WARNING ● If the light does not illuminate with the ignition switch in the ON position, have the vehicle checked by a NISSAN dealer as soon as possible.
Supplemental air bag warning light When the ignition switch is pushed to ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational.
4WD shift indicator light model) ( The light should turn off within 1 second after turning the ignition switch to ON. While the engine is running, the 4WD shift indicator light will illuminate the position selected by the 4WD shift switch. The 4WD shift indicator light may blink while shifting from one drive mode to the other.
do not need to have your vehicle towed to the dealer. ● Malfunction Indicator Light blinking — An engine misfire has been detected which may damage the emission control system. To reduce or avoid emission control system damage: – do not drive at speeds above 45 MPH (72 km/h). – avoid hard acceleration or deceleration. – avoid steep uphill grades. – if possible, reduce the amount of cargo being hauled or towed. The Malfunction Indicator Light may stop blinking and come on steady.
Transfer 4LO position model) indicator light ( ● For manual transmission models, stop the vehicle and shift the transmission selector lever to the N position with the clutch pedal depressed, then depress and turn the 4WD shift switch to 4LO or 4H. Push the Vehicle Dynamic Control off switch again or restart the engine and the system will operate normally. See “Vehicle Dynamic Control (VDC) system” in the “Starting and driving” section of this manual.
SECURITY SYSTEMS (if so equipped) The VDC system will be disabled and the VDC light will illuminate when the electronic locking rear differential (E-lock) system switch (if so equipped) is turned on and the E-lock system is engaged. If the E-lock system disengages or the switch is turned off, the VDC system will be enabled and the VDC light will turn off. The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations.
Keyfob operation: ● Push the button on the keyfob. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked. ● When the button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a reminder that the doors are already locked. The horn may or may not beep. Refer to “Silencing the horn beep feature” in the “Pre-driving checks and adjustments” section later in this manual. 4. Confirm that the indicator light comes on.
WINDSHIELD WIPER AND WASHER SWITCH If the no start condition re-occurs, NISSAN recommends placing the registered key on a separate key ring to avoid interference from other devices. Statement related to Section 15 of FCC Rules for NISSAN Vehicle Immobilizer System (CONT ASSY — IMMOBILIZER, ANT ASSY — IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada.
4 to have one sweep operaPush the lever up s tion (MIST) of the wiper. 5 to operate the Pull the lever toward you s washer. The wiper will also operate several times. WARNING In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield.
HEADLIGHT AND TURN SIGNAL SWITCH LIC0560 Type A HEADLIGHT CONTROL SWITCH Lighting 1 s When turning the switch to the position, the front parking, tail, license plate and instrument panel lights come on. 2 s When turning the switch to the position, the headlights come on and all the other lights remain on. LIC0687 Type B LIC0688 Type C CAUTION Use the headlights with the engine running to avoid discharging the vehicle battery.
To turn on the autolight system: 1. Turn the headlight switch to the AUTO posi1 . tion s 2. Turn the ignition key to ON. 3. The autolight system automatically turns the headlights on and off. Initially, if the ignition switch is turned OFF and a door is opened and left open, the headlights remain ON for 5 minutes. If another door is opened during the 5 minutes, then the 5 minute timer is reset.
After the headlights automatically turn off with the or position, headlight switch in the the headlights will illuminate again for 5 minutes if the headlight switch is moved to the OFF position and then turned to the or position. CAUTION WARNING When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.
WIC0917 LIC0563 LIC0393 INSTRUMENT BRIGHTNESS CONTROL TURN SIGNAL SWITCH FOG LIGHT SWITCH (if so equipped) The instrument brightness control operates when the headlight control switch is in the , or AUTO position (with autolights activated). Turn signal s To turn the fog lights on, turn the headlight switch to the position, then turn the fog light position. switch to the A to adjust the brightness of Turn the control s instrument panel lights when driving at night.
HAZARD WARNING FLASHER SWITCH HORN The flashers will operate with the ignition switch in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving. LIC0394 LIC0604 Push the switch on to warn other drivers when you must stop or park under emergency conditions. All turn signal lights flash. To sound the horn, push the center pad area of the steering wheel. WARNING ● If stopping for an emergency, be sure to move the vehicle well off the road.
CARGO LAMP SWITCH HEATED SEAT (if so equipped) CAUTION ● Do not use the seat heater for extended periods or when no one is using the seat. ● Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated. ● Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater. LIC0616 To turn on the cargo lamp, push the switch down to the ON position.
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH (if so equipped) HILL DESCENT CONTROL SWITCH (if so equipped) ● The hill descent control may not control the vehicle speed on a hill under all load or road conditions. Always be prepared to depress the brake pedal to control vehicle speed. Failure to do so may result in a collision or serious personal injury. CAUTION WIC0534 The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driving conditions.
ELECTRONIC LOCKING REAR DIFFERENTIAL (E-Lock) SYSTEM SWITCH (if so equipped) ● the 4WD switch must be in the 4H position and the vehicle speed must be under 21 mph (35 km/h), and ● the hill descent control system switch must be ON. When the E-Lock switch is turned ON, the indicator light will flash until the system engages. However, if all operation conditions listed above are not met or the system becomes disengaged, the indicator light will continue to flash.
CLUTCH INTERLOCK (clutch start) SWITCH (if so equipped) To use the clutch interlock switch: ● Use the E-Lock system only when freeing a stuck vehicle. Try the 4LO position before using the E-Lock system. Never use the E-Lock system on a slippery road surface such as snow or ice surface. Using the E-Lock system when driving in these road conditions may cause unexpected movement of the vehicle during engine braking, accelerating or turning, which may result in an accident and serious personal injury. 1.
POWER OUTLET ● Use power outlets with the engine running to avoid discharging the vehicle battery. ● Avoid using power outlets when the air conditioner, headlights or rear window defroster is on. ● Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF. LIC0760 Front row The power outlets are for powering electrical accessories such as cellular telephones. The bottom power outlet located on instrument panel is powered directly by the vehicle’s battery.
STORAGE LIC0764 Top center tray LIC0818 AT model LIC0819 MT model (if so equipped) STORAGE TRAYS WARNING Do not place sharp objects in the trays to help prevent injury in an accident or sudden stop.
LIC0823 MT model (if so equipped) LIC0821 2nd row under-seat storage bin (King cab model) LIC0820 2nd row under-seat storage bin (Crew cab model) 2-36 Instruments and controls Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X
UNDER-SEAT STORAGE BINS WARNING ● Do not place sharp objects in the underseat storage bins. Such objects may become dangerous projectiles and cause injury when the vehicle is moving or if the vehicle is involved in a collision. ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.
LIC0766 LIC0768 CONSOLE BOX GLOVE BOX 1 to open the console box lid Pull up on the lever s 2 . s To open the top portion of the glove box, push the A up and raise the lid. latch s To open the lower portion of the glove box, pull B down and lower the lid. the handle s Use the master key to lock or unlock the glove box. The valet key cannot be used to lock or unlock the glove box. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.
LIC0826 WIC0824 MAP POCKETS King cab model LIC0825 Crew cab model Instruments and controls 2-39 Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X
CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. ● Use only soft cups in the cup holder. Hard objects can injure you in an accident. WIC0827 LIC0575 SEAT POCKETS (if so equipped) A pocket is located on the back of the driver’s seat. Front CUP HOLDERS The front cup holders have adapters that can be removed to accommodate larger cups.
WIC0771 2nd row (rear of front console) To open the 2nd row cup holders (rear of the front console), lower the lid. To close, raise the lid. If stepped on, the cup holder is designed to snap loose from the console. To re-install, close the cup holder assembly and push it back into the console opening.
ROOF RACK (if so equipped) WARNING ● Drive extra carefully when the vehicle is loaded at or near the cargo carrying capacity, especially if the significant portion of that load is carried on the roof rack. ● Heavy loading of the roof rack has the potential to affect the vehicle stability and handling during sudden or abnormal handling maneuvers. ● Roof rack load should be evenly distributed. ● Do not exceed maximum roof rack load weight capacity.
WINDOWS Always evenly distribute the cargo on the tubular roof rack. The maximum total load is 125 lb (56 kg) evenly distributed. Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Ratings (GAWR front and rear). The GVWR and GAWR are located on the F.M.V.S.S. label (located on the driver’s side door jamb pillar).
Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close the front and rear passenger windows. To open a window, push the switch and hold it down. To close a window, pull the switch and hold it up. To stop the opening or closing function at any time, simply release the switch. LIC1329 1. 2. 3. 4. 5. 6.
LIC0787 Rear power window switch (Crew Cab models only) The rear power window switches open or close only the corresponding passenger window. To open the window, push the switch and hold it 1 . To close the window, push the switch down s 2 . up s LIC0410 WIC0263 Automatic operation MANUAL WINDOWS To fully open a window equipped with automatic operation, press the window switch down to the second detent and release it; it need not be held. The window automatically opens all the way.
MOONROOF (if so equipped) Tilting the moonroof Close the moonroof by pushing the switch to2 . Release the switch, then ward UP/CLOSE s push the UP/CLOSE switch again to tilt the moonroof up. To tilt the moonroof down, push the switch to1 . ward DOWN/OPEN s Auto reverse function (when closing or tilting down the moonroof) WIC0856 REAR SLIDING WINDOW (if so equipped) 1 , then slide Squeeze the handles of the lever s 2 .
INTERIOR LIGHTS When closing: CAUTION If the control unit detects something caught in the moonroof as it moves to the front, the moonroof will immediately open backward. When tilting down: If the control unit detects something caught in the moonroof as it tilts down, the moonroof will immediately tilt up. If the auto reverse function malfunctions and repeats opening or tilting up the moonroof, keep pushing the tilt down switch within 5 seconds after it happens; the moonroof will fully close gradually.
CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery. LIC0792 Type B ● The doors are unlocked by the keyfob, a key or the power door lock switch while all doors are closed and the ignition switch is in the OFF position. ● The driver’s door is opened and then closed while the key is removed from the ignition switch. ● The key is removed from the ignition switch while all doors are closed.
PERSONAL LIGHTS (if so equipped) MAP LIGHTS (if so equipped) HOMELINKT UNIVERSAL TRANSCEIVER (if so equipped) The HomeLinkT Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLinkT Universal Transceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems.
WARNING ● Do not use the HomeLinkT Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required by federal safety standards. (These standards became effective for opener models manufactured after April 1, 1982). A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards.
4. Hold down both buttons until the indicator light on the HomeLinkT flashes, changing from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flashing light indicates successful programming. To activate the garage door or other programmed device, press and hold the programmed HomeLinkT button — releasing when the device begins to activate. 5.
PROGRAMMING TROUBLEDIAGNOSIS CLEARING THE PROGRAMMED INFORMATION If the HomeLinkT does not quickly learn the handheld transmitter information: Individual buttons cannot be cleared. However, to clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds). ● replace the hand-held transmitter batteries with new batteries. ● position the hand-held transmitter with its battery area facing away from the HomeLinkT surface.
This transmitter has been tested and complies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. DOC: ISTC 1763K1313 FCC I.D.
MEMO 2-54 Instruments and controls
3 Pre-driving checks and adjustments Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 NISSAN vehicle immobilizer system keys (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Locking with inside lock knob . . . . . . . . . . . . . . . . . . . .
KEYS A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate. A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it. WPD0128 1. 2. 3. 4.
DOORS WARNING ● Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally opening the doors, and will help keep out intruders. ● Before opening any door, always look for and avoid oncoming traffic. ● Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls.
Lockout protection When the power door lock switch (driver’s or front passenger’s side) is moved to the lock position with the key in the ignition and any door open, all doors will lock and then unlock automatically. This helps to prevent the keys from being accidently locked inside the vehicle.
LPD0278 REAR DOORS (King Cab models) 1. Open the driver’s or passenger’s door. LPD0312 A 2. From the outside, pull the door handle s toward you. WPD0313 3. Open the door to the desired position.
REMOTE KEYLESS ENTRY SYSTEM (if so equipped) It is possible to lock/unlock all doors, turn the interior lights on, and activate the panic alarm by using the keyfob from outside the vehicle. Be sure to remove the key from the vehicle before locking the doors. The keyfob can operate at a distance of approximately 33 ft (10 m) from the vehicle. The effective distance depends on the conditions around the vehicle.
button on the keyfob. All 4. Push the the doors lock. The hazard warning lights flash twice and the horn beeps once to indicate all doors are locked. button is pushed with ● When the all doors locked, the hazard warning lights flash twice and the horn beeps once as a reminder that the doors are already locked. ● If a door is open and you push the button, the doors will lock but the horn will not beep and the hazard lights will not flash. LPD0209 HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Locking doors 1.
Push the 5 seconds. button on the keyfob again within ● All doors unlock. ● The hazard warning lights flash once if all doors are completely closed. The interior lights can be turned off without waiting 30 seconds by inserting the key into the ignition and turning to the ON or START position, locking the doors with the keyfob or pushing the interior light switch to the OFF position.
HOOD The hazard warning lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. WARNING ● Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident. Deactivating the horn beep feature does not silence the horn if the alarm is triggered. Using the interior lights ● If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.
FUEL-FILLER DOOR ● Use only an original equipment type fuel-filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emission control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator lamp to come on. ● Never pour fuel into the throttle body to attempt to start your vehicle. LPD0263 FUEL-FILLER CAP The fuel-filler cap is a ratcheting type.
STEERING WHEEL SUN VISORS CAUTION ● If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage. ● Tighten until the fuel-filler cap clicks. Failure to tighten the fuel-filler cap properly may cause the Malfunction Indicator Light (MIL) to illuminate. If the light illuminates because the fuel-filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The light should turn off after a light few driving trips.
MIRRORS 3 s Slide the extension sun visor in or out as needed. CAUTION ● Do not store the sun visor before returning the extension to its original position. ● Do not pull the extension sun visor forcedly downward. WPD0307 WPD0126 VANITY MIRRORS REARVIEW MIRROR (if so equipped) To access the vanity mirror, pull the sun visor down and flip open the mirror cover. Some vanity mirrors are illuminated and turn on when the mirror cover is open.
To turn on the automatic anti-glare feature, press button again. The indicator light will the turn on. OUTSIDE MIRRORS For information on HomeLinkT Universal Transceiver operation, see “HomeLinkT Universal Transceiver” in the “Instrument and controls” section of this manual. ● Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident.
LPD0237 WPD0170 LPD0259 Electric control type (if so equipped) Manual control type Foldable outside mirrors The outside mirror remote control will operate only when the ignition switch is in the ACC or ON position. The outside mirror can be moved in any direction for a better rear view. Pull the outside mirror toward the door to fold it. 1 to select the right or left Move the small switch s mirror. Adjust each mirror to the desired position 2 .
TRUCK BOX For proper truck box loading see “Vehicle loading information” in the “Technical and consumer information” section of this manual. WARNING ● It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
2. Hold the tailgate at a 45 degree angle. 3. Pull the tailgate out from the right side hinge. 4. Slide the tailgate out of the left side hinge. Installing the tailgate 1. Insert the tailgate into the left side hinge. 2. Hold the tailgate at a 45 degree angle and insert into the right side hinge. 3. Continue to hold the tailgate at a 45 degree angle and attach the tailgate support cables. 4. Close the tailgate securely.
WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.
MEMO 3-18 Pre-driving checks and adjustments
4 Heater, air conditioner, audio and phone systems Vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Heater and air conditioner (manual). . . . . . . . . . . . . . . . . . 4-2 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Heater operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Air conditioner operation (if so equipped) . . . . . . . . . 4-5 Air flow charts. . . . . . . . . . . . . . . . .
VENTS HEATER AND AIR CONDITIONER (manual) WARNING ● The air conditioner cooling function operates only when the engine is running. LHA0534 Adjust air flow direction for the driver’s and pas1 , driver and passensenger’s side windowss 2 , or centers 3 vent by moving the vent slide gers and/or vent assemblies. ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone.
— Air flows from defroster outlets and the front and rear floor outlets. — Air flows mainly from defroster outlets. The air flow control dial also has intermediate positions which allow the air flow to be distributed between 2 of the icon positions on the air flow control dial. Temperature control dial LHA0489 1. 2. 3. 4. 5. 6.
OFF position: again to Push the air recirculation button turn air recirculation off. The indicator light on the button will turn off. Outside air is drawn into the passenger compartment and distributed through the selected outlet. Use the off position for normal heater or air conditioner operation. Air conditioner button (if so equipped) The button is provided only on vehicles equipped with an air conditioner. HEATER OPERATION Heating 4. Turn the temperature control dial to the desired position.
turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance. Bi-level heating This mode directs cooler air from the side and center vents and warmer air from the floor outlets. When the temperature control dial is moved to the full hot or full cool position, the air between the vents and the floor outlets is the same temperature. 1. Push the button to the off position. 2. Turn the air flow control dial to the position. 3.
Dehumidified heating This mode is used to heat and dehumidify the air. 1. Push the button to the off position. 2. Turn the air flow control dial to the position. 3. Turn the fan control dial to the desired position. 4. Push the comes on. button. The indicator light 5. Turn the temperature control dial to the desired position. Dehumidified defogging This mode is used to defog the windows and dehumidify the air. 1. Turn the air flow control dial to the position. 2.
WHA0775 WHA0776 Heater, air conditioner, audio and phone systems 4-7 Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X
WHA0777 WHA0778 4-8 Heater, air conditioner, audio and phone systems Z REVIEW COPY—2008 08+ Truck/Frontier (fro) Owners Manual—USA_English (nna) 06/30/07—debbie X
SERVICING AIR CONDITIONER The air conditioner system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system.
AUDIO SYSTEM RADIO Turn the ignition key to the ACC or ON position and press the PWR (power)/VOL (volume) knob to turn the radio on. If you listen to the radio with the engine not running, the key should be turned to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other external influences. Intermittent changes in reception quality normally are caused by these external influences.
Compact disc (CD) player SATELLITE RADIO RECEPTION (if so equipped) CAUTION When the satellite radio is first installed or the battery has been replaced, the satellite radio may not work properly. This is not a malfunction. Wait more than 10 minutes with satellite radio ON and the vehicle outside of any metal or large building for satellite radio to receive all of the necessary data. ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player.
● Do not expose the CD to direct sunlight. ● CDs that are in poor condition or are dirty, scratched or covered with fingerprints may not work properly. ● The following CDs may not work properly: ● Copy control compact discs (CCCD) ● Recordable compact discs (CD-R) ● Rewritable compact discs (CD-RW) ● Do not use the following CDs as they may cause the CD player to malfunction: ● 3.
● ID3/WMA Tag — The ID3/WMA tag is the part of the encoded MP3 or WMA file that contains information about the digital music file such as song title, artist, encoding bit rate, track time duration, etc. ID3 tag information is displayed on the Artist/song title line on the display. Playback order: Music playback order of a CD with MP3 or WMA files is as illustrated. ● The names of folders not containing MP3 or WMA files are not shown in the display.
Specification chart: Supported media CD, CD-R, CD-RW Supported file systems MP3 Supported versions*1 WMA ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. Version MPEG1, MPEG2, MPEG2.5 Sampling frequency 8 kHz - 48 kHz Bit rate 8 kbps - 320 kbps, VBR Version WMA7, WMA8, WMA9 Sampling frequency 32 kHz - 48 kHz Bit rate 48 kbps - 192 kbps, VBR Tag information ID3 tag VER1.0, VER1.1, VER2.2, VER2.
Troubleshooting guide: Symptom Cause and Countermeasure Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. Cannot play If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature. Files with extensions other than “.MP3”, “.mp3” or “.wma” cannot be played.
FM/AM RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) For all operation precautions, see 9Audio operation precautions9 earlier in this section. PWR/VOL control knob Turn the ignition key to the ACC or ON position, then press the PWR/VOL control knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio or CD) that was playing immediately before the system was turned off resumes playing. When no CD is loaded, the radio comes on.
level. You can also use the SEEK/TRACK button to adjust Fader and Balance modes. Fader adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers. FM/AM radio operation Once you have adjusted the sound quality to the desired level, press the AUDIO button repeatedly until the radio or CD display reappears. Otherwise, the radio or CD display will automatically reappear after about 7 seconds.
for 5 seconds. When scanning, SCAN illuminates in the display and the radio station blinks. When temporarily stopped on a station, SCAN blinks and the radio station display is solid. Pressing the SEEK/TRACK button or again during this 5 second period stops scan tuning and the radio remains tuned to that radio station. Station memory operations: If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations.
CD EJECT: When the button is pressed with a compact disc loaded, the compact disc will be ejected. When the button is pressed while the compact disc is playing, the compact disc will eject and the system will turn off. CD IN indicator: This indicator appears on the display when a CD is loaded with the audio system on. WHA0735 1. 2. 3. 4. 5. 6. PRESET A·B·C button Display screen DISP/CLOCK button SEEK/TRACK button CD button RADIO button* 7. 8. 9. 10. 11. 12.
13. PWR/VOL control knob 14. Station and CD select (1 – 6) buttons 15. AUDIO and TUNE button *No satellite radio reception is available when the RADIO button is pressed to access satellite radio stations unless optional satellite receiver and antenna are installed and an XMT satellite radio service subscription is active. Satellite radio can only be installed in vehicles that were factory pre-wired for satellite radio. Satellite radio is not available in Alaska, Hawaii and Guam.
DISP (display) button: This DISP (display) button will show text about MP3, SAT or CD information in the audio display. CD display mode To change the text displayed while playing a CD with text, press the DISP button. The DISP button will allow you to scroll through CD text as follows: Disc title ←→ Track title.
● Title mode displays the song title, show name, or temperature of the selected satellite radio station. FM/AM/SAT radio operation FM/AM/SAT band select: Pushing the RADIO button will change the band as follows: If a compact disc is playing when the RADIO button is pushed, the compact disc will automatically be turned off and the last radio station played will come on. The FM stereo indicator ST will glow during FM stereo reception.
5. Other buttons can be set in the same manner. If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Radio data system (RDS): RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band). Currently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data.
MP3 CAT FOLDER button: While playing an MP3 CD, press the CAT FOLDER button or to scan backward or forward through available folders. Press and hold the CAT FOLDER button or to fast forward or rewind a track on an MP3 CD. CD select buttons: To play another CD that has been loaded, press a CD select button (1 – 6).
LHA0269 LHA0049 CD CARE AND CLEANING ● Handle a CD by its edges. Do not bend the disc. Never touch the surface of the disc. ● Always place the discs in the storage case when they are not being used. ● To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion. ● Do not use a conventional record cleaner or alcohol intended for industrial use. ● A new disc may be rough on the inner and outer edges.
STEERING WHEEL SWITCH FOR AUDIO CONTROL The audio system can be operated using the controls on the steering wheel. POWER on/off switch With the ignition key turned to the ACC or ON position, push the POWER switch to turn the audio system on or off. If you have the Type B switch, with the ignition key turned to the ACC or ON position, push the MODE switch to turn the audio system on.
CAR PHONE OR CB RADIO When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following precautions, otherwise the new equipment may adversely affect the engine control system and other electronic parts. WARNING ● A cellular telephone should not be used while driving so full attention may be given to vehicle operation. Some jurisdictions prohibit the use of cellular telephones while driving.
module when the ignition switch is turned to the ON position with the paired cellular phone turned on and carried in the vehicle. You can register up to 5 different BluetoothT cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. Before using the BluetoothT Hands-Free Phone System, refer to the following notes. ● Set up the wireless connection between a cellular phone and the in-vehicle phone module before using the hands-free phone system.
– Your cellular phone is locked to prevent it from being dialed. ● When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult to hear the other person’s voice during a call. ● Do not place the cellular phone in an area surrounded by metal or far away from the in-vehicle phone module to prevent tone quality degradation and wireless connection disruption.
Giving voice commands To operate NISSAN Voice Recognition, press and release the button located on the steering wheel. The light on the overhead console flashes to signal you have entered a voice recognition (VR) session. After the tone sounds, speak a command. The command given is picked up by the microphone, and voice feedback is given when the command is accepted. ● If you need to hear the available commands for the current menu again, say “Help” and the system will repeat them.
The system repeats the numbers and prompts you to enter more. PHONE/END Press the button to cancel a VR session or end a call. – “six two oh oh” ● You can say “Star” for * and “Pound” for # at any time in any position of the phone number. GETTING STARTED The following procedures will help you get started using the BluetoothT Hands-Free Phone System with NISSAN Voice Recognition. For additional command options, refer to “List of voice commands” later in this section.
4. The system announces the current language and gives you the option to change the language to Spanish (in Spanish) or French (in French). Use the following chart to select the language. NOTE: button or You must press the the button within 5 seconds to change the language. Current language Press (PHONE/SEND) to select Press (PHONE/END) to select English Spanish French Spanish English French French English Spanish 5. If you decide not to change the language, do not press either button.
6. The system asks you to assign a priority level F . The priority level determines which s phone is active when more than one paired BluetoothT phone is in the vehicle. Follow the instructions provided by the system or refer to “Setup” later in this section for more information on changing priorities. 7. The system will ask if you would like to select G .
When you get used to the menus in the system, you can talk ahead by saying more than one command at a time. For example, say, “Call five five five one two one two” or “Memo pad record.” Also, when you get used to the system responses, you can skip ahead to the tone by pressing the button on the steering wheel. However, if you press the button when the system is waiting for a response from you it will end the VR session.
The system acknowledges the command and sends the tones associated with the numbers. The system then ends the VR session and returns to the call. ● “Transfer call” — Use the Transfer Call command to transfer the call from the BluetoothT Hands-Free Phone System to the cellular phone when privacy is desired. “Phone book” NOTE: ● “Mute” — Use the Mute command to mute your voice so the other party cannot hear it. Use the mute command again to unmute your voice.
number will be transferred from the cellular phone via the BluetoothT communication link. The transfer procedure varies according to each cellular phone. See the cellular phone Owner’s Manual for details. You can also visit www.nissanusa.com/bluetooth for instructions on transferring phone numbers from NISSAN recommended cellular phones. The system repeats the number and prompts you for the next command. When you have finished entering numbers or transferring an entry, choose “Store.
You can stop the playback of the list at any time by pressing the button on the steering wheel. The system ends the VR session. “Memo pad” Main Menu “Memo Pad” A “Record” s B “Play” s C “Delete” s The Memo Pad records a maximum of 6 voice memos, each up to 20 seconds long. A “Record” s The system announces “Recording” and a tone sounds, signaling you to begin. Speak the information you wish to record clearly. When you are done, press the or button on the steering wheel.
● “Replace phone” — The system announces the names of the phones already paired and asks which you would like to replace. Once you say the name of the phone you wish to replace, the pairing procedure will begin. Refer to “Pairing procedure” earlier in this section. ● “List phone” – See the description below. B “List phone” s Use the List Phone command to hear the names of the phones currently paired. If no phones are paired, the system announces, “No paired phones to list.
G “Bluetooth off” s Training procedure Use the Bluetooth Off command to turn off the BluetoothT Hands-Free Phone System. The procedure for training a voice is as follows. When the BluetoothT Hands-Free Phone System is off, you will not be able to make or receive calls using NISSAN Voice Recognition. Also, you will not have access to the Phone Book. You can still use the Memo Pad and access Setup.
Training phrases ● call three one nine oh two ● go back During the SA mode, the system instructs the trainer to say the following phrases. (The system will prompt you for each phrase.
TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty. If problems are encountered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved. Symptom Solution 1. Ensure that the command is valid. See “List of voice commands” earlier in this section. 2. Ensure that the command is spoken after the tone. 3.
MEMO 4-42 Heater, air conditioner, audio and phone systems
5 Starting and driving Precautions when starting and driving. . . . . . . . . . . . . . . . 5-2 Exhaust gas (carbon monoxide) . . . . . . . . . . . . . . . . . . 5-2 Three-way catalyst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Tire Pressure Monitoring System (TPMS). . . . . . . . . . 5-3 On-pavement and off-road driving precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Avoiding collision and rollover . . . . . . . . . . . . . . . . . . . .
PRECAUTIONS WHEN STARTING AND DRIVING WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously reduce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up. Malfunctions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat.
km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving). ● The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure.
Some examples are: – Facilities or electric devices using similar radio frequencies are near the vehicle. – If a transmitter set to similar frequencies is being used in or near the vehicle. – If a computer (or similar equipment) or a DC/AC converter is being used in or near the vehicle. FCC Notice: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
DRINKING ALCOHOL/DRUGS AND DRIVING WARNING Never drive under the influence of alcohol or drugs. Alcohol in the bloodstream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the severity of the injury. DRIVING SAFETY PRECAUTIONS Your NISSAN is designed for both normal and off-road use.
● Unsecured cargo can be thrown around when driving over rough terrain. Properly secure all cargo so it will not be thrown forward and cause injury to you or your passengers. ● Lower your speed when encountering strong crosswinds. With a higher center of gravity, your NISSAN is more affected by strong side winds. Slower speeds ensure better vehicle control.
IGNITION SWITCH ● Always use tires of the same type, size, brand, construction (bias, bias-belted, or radial), and tread pattern on all four wheels. Install tire chains on the rear wheels when driving on slippery roads and drive carefully. ● Be sure to check the brakes immediately after driving in mud or water. See “Brake system” later in this section for “Wet brakes”. WARNING Never remove or turn the key to the LOCK position while driving. The steering wheel will lock.
To remove the key from the ignition switch: 1. Shift the selector lever to the P (Park) position with the key in the ON position. 2. Turn the key to the LOCK position. 3. Remove the key from the ignition. If the selector lever is shifted to the P (Park) position after the key is turned to the OFF position or when the key cannot be turned to the LOCK position, proceed as follows to remove the key. 1. Move the shift selector lever into the P (Park) position. 2.
BEFORE STARTING THE ENGINE To lock the steering wheel, turn the key to the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left. KEY POSITIONS LOCK: Normal parking position (0) OFF: (Not used) (1) ACC: (Accessories) (2) This position activates electrical accessories such as the radio when the engine is not running.
STARTING THE ENGINE 1. Apply the parking brake. 2. Automatic transmission: Move the shift selector lever to P (Park) or N (Neutral). P (Park) is recommended. The shift selector lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to the OFF position or if the key is removed from the ignition switch. The starter is designed not to operate if the shift selector lever is in any of the driving positions.
DRIVING THE VEHICLE AUTOMATIC TRANSMISSION WARNING ● Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), D (Drive), 3, 2 or 1. Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident. ● Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up. ● Never shift to P (Park) or R (Reverse) while the vehicle is moving.
WARNING Apply the parking brake if the selector lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage. If the key is turned to the OFF or ACC position for any reason while the vehicle is in N (Neutral), or any D (Drive) position, the key cannot be turned to the LOCK position and be removed from the ignition switch.
Do not downshift into the 1 position at speeds over the following and do not exceed the following speeds in the 1 position. 1. Turn the ignition key to the LOCK position and remove the key 2. Apply the parking brake. 2WD and AUTO: 3. Remove the shift lock release cover as shown. 43 MPH (70 km/h) 4H: 4. Insert a small screwdriver in the shift lock release slot and push down. 43 MPH (70 km/h) 5. Move the shift selector lever to the N (Neutral) position while holding down the shift lock release.
Accelerator downshift — in D position — OFF: For passing or hill climbing, depress the accelerator pedal to the floor. This shifts the transmission down into a lower gear, depending on the vehicle speed. For driving up and down long slopes where engine braking is necessary push the Overdrive switch once. The O/D OFF indicator light in the instrument panel comes on at this time.
MANUAL TRANSMISSION (if so equipped) WARNING ● Do not downshift abruptly on slippery roads. This may cause a loss of control. ● Do not over-rev the engine when shifting to a lower gear. This may cause a loss of control or engine damage. CAUTION ● Do not rest your foot on the clutch pedal while driving. This may cause clutch damage. ● Fully depress the clutch pedal before shifting to help prevent transmission damage.
Suggested upshift speeds Suggested maximum speed in each gear 4–wheel drive models (VQ40DE engine) The following are suggested vehicle speeds for shifting into a higher gear. These suggestions relate to fuel economy and vehicle performance. Actual upshift speeds will vary according to road conditions, the weather and individual driving habits. Downshift to a lower gear if the engine is not running smoothly, or if you need to accelerate.
PARKING BRAKE 4. Before driving, be sure the brake warning light goes out. WARNING ● Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident. ● Do not release the parking brake from outside the vehicle. ● Do not use the gear shift in place of the parking brake. When parking, be sure the parking brake is fully engaged. ● Do not leave children unattended in a vehicle. They could release the parking brake and cause an accident. LSD0150 A.
CRUISE CONTROL (if so equipped) PRECAUTIONS ON CRUISE CONTROL ● If the cruise control system malfunctions, it cancels automatically. The SET indicator light in the instrument panel then blinks to warn the driver. ● If the SET indicator light blinks, turn the cruise control main switch off and have the system checked by a NISSAN dealer. WSD0153 1. 2. 3. 4.
BREAK-IN SCHEDULE ● The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control. To cancel the preset speed, use one of the following three methods. ● Push the CANCEL button; the SET indicator light in the instrument panel goes out. ● Tap the brake pedal; the SET indicator light goes out. ● Turn the main switch off. Both the CRUISE indicator light and SET indicator light in the instrument panel go out.
INCREASING FUEL ECONOMY USING FOUR WHEEL DRIVE (4WD) ● Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelerator position. ● When cruising at highway speeds, it is more economical to use the air conditioner and leave the windows closed to reduce drag. ● Drive at moderate speeds on the highway. Driving at high speed lowers fuel economy. ● ● Avoid unnecessary stopping and braking. Maintain a safe distance behind other vehicles.
CAUTION ● Do not drive the vehicle in the 4H or 4LO position on dry hard surface roads. Driving on dry, hard surfaces in 4H or 4LO may cause unnecessary noise, tire wear and increased fuel consumption. TRANSFER CASE SHIFTING PROCEDURES The part time 4WD system provides 3 positions (2WD, 4H and 4LO), so you can select the desired drive mode according to the driving conditions.
2WD or 4WD shift procedure: 4WD Shift Switch Position 2WD Wheels Driven Indicator Light Use Conditions 4WD shift 4WD Shift Procedure Transfer 4LO position Rear wheels For driving on dry, paved roads (Economy drive) or state dynamometer I/M testing 4 wheels For driving on rocky, sandy or snow-covered roads Move the 4WD switch. 2WD <—> 4H 4WD shift indicator light will indicate transfer shift position engaged.
The transfer case 4WD shift switch is used to select either 2WD or 4WD depending on the driving conditions. There are three types of drive modes available, 2WD, 4H and 4LO. The 4WD shift switch electronically controls the transfer case operation. Rotate the switch to move between each mode, 2WD, 4H and 4LO.
When the vehicle is stuck, CAUTION ● Set the 4WD shift switch to 4H or 4LO. ● When driving straight, shift the 4WD shift switch to the 2WD or 4H position. Do not move the 4WD shift switch when making a turn or reversing. ● Use the Electronic Locking Rear Differential (E-Lock) system (if so equipped). Turn the switch ON while the vehicle is stationary and apply the throttle to try to free the vehicle. ● Do not shift the 4WD shift switch while driving on steep downhill grades.
● If the 4WD warning light comes on, the 4WD indicator light goes out. CAUTION If the 4WD shift indicator light indication changes to 2WD when the 4WD shift switch is shifted to the 4H position at low ambient temperatures, the 2WD mode may be being engaged due to malfunctioning drive system. If the indicator does not return to normal and the 4WD warning light comes on, have the system checked by the nearest NISSAN dealer. LSD0147 The 4WD shift indicator light is located in the odometer display.
ELECTRONIC LOCKING REAR DIFFERENTIAL (E-Lock) SYSTEM (if so equipped) ● When the warning light comes on, the 2WD mode may be engaged even if the 4WD shift switch is in 4H. Be especially careful when driving. If corresponding parts are malfunctioning, the 4WD mode will not be engaged even if the 4WD shift switch is shifted. ● Do not drive the vehicle in the 4H or 4LO position on dry hard surface roads.
WARNING ● Never leave the E-Lock system ON when driving on paved or hard-surfaced roads. Turning the vehicle may result in the rear wheels slipping and result in an accident and personal injury. After using the E-Lock system to free the vehicle, turn the system OFF. ● Use the E-Lock system only when freeing a stuck vehicle. Try the 4LO position before using the E-Lock system. Never use the E-Lock system on a slippery road surface such as snow or ice surface.
PARKING/PARKING ON HILLS Place the shift lever in the R (Reverse) position. When parking on an uphill grade, place the shift lever in 1st gear. Automatic transmission models: Move the shift selector lever to the P (Park) position. 3. To help prevent the vehicle from rolling into traffic when parked on an incline, it is a good practice to turn the wheels as illustrated.
POWER STEERING BRAKE SYSTEM The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at two wheels. If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds.
This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer. ANTI-LOCK BRAKING SYSTEM (ABS) WARNING ● The Anti-lock Braking System (ABS) is a sophisticated device, but it cannot prevent accidents resulting from careless or dangerous driving techniques. It can help maintain vehicle control during braking on slippery surfaces. Remember that stopping distances on slippery surfaces will be longer than on normal surfaces even with ABS.
ACTIVE BRAKE LIMITED SLIP (ABLS) SYSTEM (if so equipped) When the ABS senses that one or more wheels are close to locking up, the system electronically controls the pressure applied to each brake. This action is similar to pumping the brakes very quickly. You may feel a pulsation in the brake pedal and hear a noise from under the hood or feel a vibration from the actuator when it is operating. This is normal and indicates that the ABS is operating properly.
● Drive the vehicle at speeds above 10 mph (15 km/h) for at least 10 minutes. ● The VDC OFF indicator light should go off indicating the traction control system is operational. ● If you interrupt the reset procedure by turning the ignition off, you will need to restart the reset procedure. If after driving the vehicle for more than 10 minutes and the SLIP and lights remain illuminated in the instrument panel, have the Vehicle Dynamic Control system checked by a NISSAN dealer.
HILL DESCENT CONTROL SYSTEM (if so equipped) WARNING ● Never rely solely on the hill descent control system to control vehicle speed when driving on steep down hill grades. Always drive carefully and attentively when using the hill descent control system and decelerate the vehicle speed by depressing the brake pedal if necessary. Be especially careful when driving on frozen, muddy or an extremely steep downhill roads.
COLD WEATHER DRIVING The hill start assist system automatically keeps the brakes applied to help prevent the vehicle from rolling backwards in the time it takes the driver to release the brake pedal and apply the accelerator when the vehicle is stopped on a hill. Hill start assist will operate automatically under the following conditions: ● The selector lever is shifted to a forward or reverse gear. ● The vehicle is stopped completely on a hill by applying the brake. The maximum holding time is 2 seconds.
3. Tire chains may be used. For details see “Tire chains” in the “Maintenance and do-ityourself” section of this manual. SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter: ● A scraper and stiff-bristled brush to remove ice and snow from the windows and wiper blades. ● A sturdy, flat board to be placed under the jack to give it firm support. ● A shovel to dig the vehicle out of snowdrifts. ● Extra window washer fluid to refill the reservoir tank.
To use the engine block heater: 1. Turn the engine off. 2. Open the hood and unwrap the engine block heater cord. 3. Plug the engine block heater cord into a grounded 3-wire, 3-pronged extension cord. 4. Plug the extension cord into a Ground Fault Interrupt (GFI) protected, grounded 110volt AC (VAC) outlet. 5. The engine block heater must be plugged in for at least 2 - 4 hours, depending on outside temperatures, to properly warm the engine coolant.
MEMO 5-38 Starting and driving
6 In case of emergency First aid kit (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Tire Pressure Monitoring System (TPMS). . . . . . . . . . 6-3 Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 Push starting. . . . . . . . . . . . . . . . . . . . . . . . . .
FIRST AID KIT (if so equipped) The first aid kit is located in the under-seat storage bins. To access the first aid kit: LCE0108 King cab model For King cab model, lift up the rear jump seat and remove net to remove the first aid kit. Refer to “Jump Seats” in the “Safety — Seats, seat belts and supplemental restraint system” section earlier in the manual. LCE0113 Crew cab model For Crew cab model, lift up the rear bench seat and remove the net to remove the first aid kit.
FLAT TIRE TIRE PRESSURE MONITORING SYSTEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. If the vehicle is being driven with low tire pressure, the TPMS will activate and warn you of it by the low tire pressure warning light.
WARNING ● Make sure the parking brake is securely applied and the manual transmission is shifted into R (Reverse), or the automatic transmission into P (Park). ● Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous. ● Never change tires if oncoming traffic is close to your vehicle. Wait for professional road assistance.
All models: 1. Fit the square end of the jack rod into the square hole of the wheel nut wrench to form a handle. 2. Find the oval-shaped opening under the middle of the tailgate. Pass the T-shaped end of the jack rod through the opening and direct it toward the spare tire winch, located directly above the spare tire. LCE0110 LCE0111 For Crew Cab models: The tools and tool case are located behind the rear bench seat. ● Fold the rear bench seat down.
4. Once the spare tire is completely lowered, reach under the vehicle, remove the retainer chain, and carefully slide the tire from under the rear of the vehicle. CAUTION Be sure to center the spare tire suspending plate on the wheel and then lift the spare tire. Jacking up vehicle and removing the damaged tire WARNING ● Never get under the vehicle while it is supported only by the jack. If it is necessary to work under the vehicle, support it with safety stands. WCE0070 3.
2. Place the jack directly under the jack-up point as illustrated so the top of the jack contacts the vehicle at the jack-up point. The jack-up points are indicated by stamped arrows on the side of the frame. WCE0152 LCE0087 The jack should be used on firm and level ground. 3. Install the assembled jack rod into the jack as shown. 4. To lift the vehicle, securely hold the jack lever and rod. Carefully raise the vehicle until the tire clears the ground.
5. Remove the wheel nuts and then remove the tire. 4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated. Lower the vehicle completely. WARNING ● Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident. WCE0063 Installing the spare tire The spare tire is designed for emergency use.
JUMP STARTING Adjust tire pressure to the COLD pressure. COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km). COLD tire pressures are shown on the Tire and Loading Information label affixed to the driver side center pillar. 5. Securely store the flat tire and jacking equipment in the vehicle. WARNING ● Always make sure that the spare tire and jacking equipment are properly secured after use.
CAUTION ● Always connect positive (1) to positive (1) and negative (2) to body ground (for example, strut mounting bolt, engine lift bracket, etc.) — not to the battery. ● Make sure the jumper cables do not touch moving parts in the engine compartment and that the cable clamps do not contact any other metal. 5. Start the engine of the booster vehicle and let it run for a few minutes. WCE0054 WARNING Always follow the instructions below.
PUSH STARTING 8. Replace the vent caps (if so equipped). Be sure to dispose of the cloth used to cover the vent holes as it may be contaminated with corrosive acid. IF YOUR VEHICLE OVERHEATS CAUTION ● Do not push start this vehicle. The three-way catalyst may be damaged. ● Automatic transmission models cannot be push-started or tow-started. Attempting to do so may cause transmission damage. ● For manual transmission models, never try to start the vehicle by towing it.
TOWING YOUR VEHICLE 3. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. (If steam or coolant is escaping, turn off the engine.) Do not open the hood further until no steam or coolant can be seen. 4. Open the engine hood. WARNING If steam or water is coming from the engine, stand clear to prevent getting burned. 5. Visually check drive belts for damage or looseness. Also check if the cooling fan is running.
For information about towing your vehicle behind a recreational vehicle (RV), refer to “Flat towing” in the “Technical and consumer information” section of this manual. Two-wheel drive models NISSAN recommends that your vehicle be towed with the driving (rear) wheels off the ground or place the vehicle on a flat bed truck as illustrated.
● If you have to tow manual transmission models with the rear wheels on the ground (if you do not use towing dollies) or four wheels on the ground: ● Always release the parking brake. ● Move the transmission shift lever to the N (Neutral) position.
WARNING ● Stand clear of a stuck vehicle. ● Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged. CAUTION LCE0103 VEHICLE RECOVERY (freeing a stuck vehicle) Pulling a stuck vehicle If your vehicle is stuck in sand, snow, mud, etc., use a tow strap or other device designed specifically for vehicle recovery. Always follow the recovery device manufacturer’s instructions.
MEMO 6-16 In case of emergency
7 Appearance and care Cleaning exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Removing spots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Underbody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Glass . . . . . . . . . . . . . . . . . . . . . . .
CLEANING EXTERIOR In order to maintain the appearance of your vehicle, it is important to take proper care of it. To protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads. ● when contaminants such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface. ● when dust or mud builds up on the surface.
REMOVING SPOTS CAUTION Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store. When cleaning the inside of the windows, do not use sharp-edged tools, abrasive cleaners or chlorine-based disinfectant cleaners. They could damage the electrical conductors, radio antenna elements or rear window defroster elements.
CLEANING INTERIOR Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry, soft cloth. ● Never use fabric protectors unless recommended by the manufacturer. Regular care and cleaning is required in order to maintain the appearance of the leather.
CORROSION PROTECTION SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See “Seat belt maintenance” in the “Safety – Seats, seat belts and supplemental restraint system” section of this manual. WARNING Do not allow wet seat belts to roll up in the retractor. NEVER use bleach, dye or chemical solvents to clean the seat belts, since these materials may severely weaken the seat belt webbing.
CAUTION ● NEVER remove dirt, sand or other debris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. ● Never allow water or other liquids to come in contact with electronic components inside the vehicle as this may damage them. Chemicals used for road surface de-icing are extremely corrosive. They accelerate corrosion and deterioration of underbody components such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders.
8 Maintenance and do-it-yourself Maintenance requirements. . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Explanation of general maintenance items . . . . . . . . . 8-2 Maintenance precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Engine compartment check locations . . . . . . . . . . . . . . . . 8-6 Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE REQUIREMENTS Your new NISSAN has been designed to have minimum maintenance requirements with long service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN’s good mechanical condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed.
When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts (lug nuts)* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary.
Steering wheel Check for changes in the steering system, such as excessive freeplay, hard steering or strange noises. Warning lights and chimes Make sure all warning lights and chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner.
MAINTENANCE PRECAUTIONS When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed. WARNING ● Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the vehicle from moving. Move the shift selector lever to P (Park).
ENGINE COMPARTMENT CHECK LOCATIONS QR25DE engine 1. 2. 3. 4. 5. 6. 7. Windshield washer fluid reservoir Fuse/Fusible link box Fuse and relay box Air cleaner Engine oil filler cap Engine oil dipstick Brake fluid reservoir/ Clutch fluid reservoir (M/T model) 8. Drive belt location 9. Radiator cap 10. Power steering fluid reservoir 11. Battery 12. Engine coolant reservoir NOTE: Engine cover removed for clarity.
VQ40DE engine 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
ENGINE COOLING SYSTEM The engine cooling system is filled at the factory with Genuine NISSAN Long Life Antifreeze/Coolant to provide year-round antifreeze and coolant protection.The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary. WARNING ● Never remove the radiator or coolant reservoir cap when the engine is hot. Wait until the engine and radiator cool down.
ENGINE OIL CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheating. WARNING ● To avoid the danger of being scalded, never change the coolant when the engine is hot. LDI0466 Type B If the cooling system frequently requires coolant, have it checked by a NISSAN dealer.
LDI0467 Type B 5. Remove the dipstick again and check the oil level. It should be between the H (High) and B . This is the normal operL (Low) marks s ating oil level range. If the oil level is below A , remove the oil filler cap the L (Low) mark s and pour recommended oil through the C. opening. Do not overfill s 6. Recheck oil level with the dipstick. It is normal to add some oil between oil maintenance intervals or during the break-in period, depending on the severity of operating conditions.
CAUTION Be careful not to burn yourself. The engine oil may be hot. 9. Turn the engine off and wait more than 10 minutes. Check the oil level with the dipstick. Add engine oil if necessary. ● Waste oil must be disposed of properly. ● Check your local regulations. 6. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with a wrench. Do not use excessive force.
7. Coat the gasket on the new filter with clean engine oil. 8. Screw on the oil filter until a slight resistance is felt, then tighten an additional 2/3 turn. 9. Start the engine and check for leakage around the oil filter. Correct as required. 10. Turn the engine off and wait more than 10 minutes. Check the oil level. Add engine oil if necessary. WDI0502 VQ40DE CHANGING ENGINE OIL FILTER 1. Park the vehicle on a level surface and apply the parking brake. 2. Turn the engine off. 3.
5-SPEED AUTOMATIC TRANSMISSION FLUID POWER STEERING FLUID When checking or replacement is required, we recommend your NISSAN dealer for servicing. CAUTION ● DO NOT OVERFILL. CAUTION ● Recommended fluid is NISSAN PSF or equivalent. ● Use only Genuine NISSAN Matic J ATF. Do not mix with other fluids.
BRAKE AND CLUTCH FLUID For further brake and clutch fluid specification information, refer to “Capacities and recommended fuel/lubricants” in the “Technical and consumer information” section of this manual. WARNING ● Use only new fluid from a sealed container. Old, inferior or contaminated fluid may damage the brake and clutch systems. The use of improper fluids can damage the brake and clutch system and affect the vehicle’s stopping ability. ● Clean the filler cap before removing.
WINDOW WASHER FLUID BATTERY Refill the reservoir more frequently when driving conditions require an increased amount of window washer fluid. ● Keep the battery surface clean and dry. Clean the battery with a solution of baking soda and water. Recommended fluid is Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent. ● Make certain the terminal connections are clean and securely tightened. CAUTION ● Do not substitute engine anti-freeze coolant for window washer solution.
● When working on or near a battery, always wear suitable eye protection and remove all jewelry. ● Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. ● Keep battery out of the reach of children. WDI0224 1. Remove the battery caps with a screwdriver as shown. Use a cloth to protect the battery case. LDI0302 2. Check the fluid level in each cell.
VARIABLE VOLTAGE CONTROL SYSTEM Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. Your vehicle is equipped with a variable voltage control system. This system measures the amount of electrical discharge from the battery and controls voltage generated by the generator. JUMP STARTING A is located near the battery The current sensor s along the negative battery cable.
DRIVE BELT 1. Visually inspect the belt for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or is loose, have it replaced or adjusted by a NISSAN dealer. 2. Have the belt checked regularly for condition and tension in accordance with the maintenance schedule found in the “NISSAN Service and Maintenance Guide”. WDI0639 LDI0461 VQ40DE 1. 2. 3. 4. 5. 6.
SPARK PLUGS WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely. CAUTION CAUTION Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs. If replacement is required, see your NISSAN dealer for assistance. Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs.
AIR CLEANER WARNING ● Operating the engine with the air cleaner removed can cause you or others to be burned. The air cleaner not only cleans the air, it stops the flame if the engine backfires. If it isn’t there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed. LDI0376 Type A The air cleaner filter should not be cleaned and reused.
IN-CABIN MICROFILTER The in-cabin microfilter restricts the entry of airborne dust and pollen particles and reduces some objectionable outside odors. The filter is located behind the glove box. Refer to the “NISSAN Service and Maintenance Guide” for change intervals. To replace the filter, perform the following procedure: LDI0442 LDI0472 1. Open the glove box and press in on the sides so that it will open completely allowing it to hang by the cord. 2.
WINDSHIELD WIPER BLADES CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. LDI0473 NOTE: The filters are marked with air flow arrows. The end of the filter with the arrow should face the rear of the vehicle.
BRAKES If the brakes do not operate properly, have the brakes checked by a NISSAN dealer. CAUTION ● After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened. Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. ● Make sure the wiper blades contact the glass; otherwise the arms may be damaged from wind pressure. The front and rear disc-type brakes self-adjust every time the brake pedal is applied.
FUSES Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate maintenance schedule information in the “NISSAN Service and Maintenance Guide”. LDI0455 LDI0457 Two types of fuses are used. Type A is used in the fuse boxes in the engine compartment. Type B is used in the passenger compartment fuse box. If a type A fuse is used to replace a type B fuse, the type A fuse will not be level with the fuse pocket as shown in the illustration.
3. Remove the fuse box cover by pushing the tab and lifting the cover up. 4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment. LDI0444 ENGINE COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire. If any electrical equipment does not come on, check for an open fuse. 1.
WDI0452 LDI0445 PASSENGER COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire. Type A A , replace it with an 4. If the fuse is open s B. equivalent good fuse s LDI0456 Type B 5. Push the fuse box cover to install. 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer. If any electrical equipment does not operate, check for an open fuse. 1.
KEYFOB BATTERY REPLACEMENT 3 s C with the “+” facing Install a new battery s down. Recommended battery: CR2025 or equivalent. 4 s Close the lid securely. 5. Press the button, then the button two or three times to check the keyfob operation. If the battery is removed for any reason other than replacement, perform step 5. ● An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal.
LIGHTS This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. HEADLIGHTS The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb.
4. Turn the bulb retaining ring counterclockwise until it is free form the headlight reflecA. tor and then remove it s 5. Carefully remove the headlight bulb. Do not shake or rotate the bulb when removing it B. s Replacing the headlight bulb 1. Insert the bulb. DO NOT TOUCH THE BULB WITH BARE HANDS. 2. Install and tighten the bulb retainer. ● Be sure the lip of the bulb socket contacts the headlight body. 3. Push the electrical connector into the bulb plastic base until it snaps and stops. 4.
EXTERIOR AND INTERIOR LIGHTS Wattage (W) Bulb No.*1 Headlight 65/55 9007 (HB5) Turn signal light/Parking light 28/8 3457K 3.
1. 2. 3. 4. 5. 6. 7. Map lights/personal lights Room light High-mount stoplight/cargo lights License plate light Rear combination light Fog light (if so equipped) Headlight assembly LDI0459 WDI0306 Replacement procedures Map lights/personal lights All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens and/or cover.
WDI0206 Room light 1 to protect the housing.
WHEELS AND TIRES If you have a flat tire, see the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h).
● Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level. ● Do not drive your vehicle over 85 MPH (137 km/h) unless it is equipped with high speed rated tires. Driving faster than 85 MPH (137 km/h) may result in tire failure, loss of control and possible injury.
6 s 4. Read the tire pressure on the gauge stem and compare to the specification shown on the F.M.V.S.S./C.M.V.S.S. label or the Tire and Loading Information label (if so equipped). Spare tire size or compact spare tire size (if so equipped). LDI0393 Checking tire pressure 1. Remove the valve stem cap from the tire. 5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure.
Size Front Original Tire: P235/75R15 105S P265/70R16 111S P265/75R16 114T P265/65R17 110S Rear Original Tire: P235/75R15 109S P265/70R16 111S P265/75R16 114T P265/65R17 110S Spare Tire: P235/75R15 109S P265/70R16 111S P265/75R16 114T P265/65R17 110S Cold Tire Inflation Pressure 240 kPa, 35 PSI 240 kPa, 35 PSI WDI0394 Example TIRE LABELING 240 kPa, 35 PSI Federal law requires tire manufacturers to place standardized information on the sidewall of all tires.
7. H: Tire speed rating. You should not drive the vehicle faster than the tire speed rating. WDI0395 Example 1 Tire size (example: P215/65R15 95H) s 1. P: The 9P9 indicates the tire is designed for passenger vehicles (not all tires have this information). 2. Three-digit number (215): This number gives the width in millimeters of the tire from sidewall edge to sidewall edge. 3. Two-digit number (65): This number, known as the aspect ratio, gives the tire’s ratio of height to width. 4.
The number of layers or plies of rubbercoated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. 4 Maximum permissible inflation press sure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure. WDI0396 Example 2 TIN (Tire Identification Number) for a s new tire (example: DOT XX XX XXX XXXX) 1.
7 The word “radial” s The word “radial” is shown if the tire has radial structure. 8 Manufacturer or brand name s Manufacturer or brand name is shown.
studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer’s suggestions. Use only SAE class “S” chains.
Wheel nut tightening torque: ● The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced. 98 ft-lb (133 N·m) The wheel nuts must be kept tightened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval. ● Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician because some tire damage may not be obvious.
Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in “Wheels and tires” in the “Technical and consumer information” section of this manual.
If excessive tire wear is found, it is recommended that all four tires be replaced with tires of the same size, brand, construction and tread pattern. The tire pressure and wheel alignment should also be checked and corrected as necessary. Contact a NISSAN dealer. Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required.
MEMO 8-44 Maintenance and do-it-yourself
9 Technical and consumer information Capacities and recommended fuel/lubricants . . . . . . . . . 9-2 Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Engine oil and oil filter recommendations . . . . . . . . . . 9-5 Air conditioner system refrigerant and oil recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 Engine . . . . . . . . . . . . . . . . . . . . . .
CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity.
FUEL RECOMMENDATION Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). ● Do not use E-85 fuel in your vehicle. Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel can damage the fuel system components and is not covered by the NISSAN new vehicle limited warranty. For 4.0L engine.
If any driveability problems such as engine stalling and difficult hot-starting are experienced after using oxygenate-blend fuels, immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refueling. Gasoline containing oxygenates can cause paint damage. E–85 fuel E-85 fuel is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. E-85 can only be used in a Flexible Fuel Vehicle (FFV). Do not use E-85 in your vehicle. U.S.
Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be operated before the next oil change. Choosing an oil viscosity other than that recommended could cause serious engine damage.
the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes: ● repeated short distance driving at cold outside temperatures ● driving in dusty conditions ● extensive idling ● towing a trailer ● stop and go commuting Refer to the “NISSAN Service and Maintenance Guide” for the maintenance schedule.
SPECIFICATIONS ENGINE Model QR25DE VQ40DE Type Gasoline, 4-cycle, DOHC Gasoline, 4-cycle, DOHC Cylinder arrangement 4-cylinder in-line 6-cylinder, V-block, Slanted at 60° Bore x Stroke Displacement Firing order in (mm) 3.5 x 3.9 (89.0 x 100.0) cu in (cm3) 151.82 (2,488) 1–3–4–2 3.760 x 3.622 (95.5 x 92) 241.30 (3,954) 1–2–3–4–5–6 Idle speed M/T A/T (in “N” position) See the “Emission Control Information label” on the underside of the hood. Ignition timing (degree B.T.D.C.
WHEELS AND TIRES DIMENSIONS AND WEIGHTS Wheels Overall length 15 x 7.0J Short wheel base in (mm) 205.6(5222) 16 x 7.0J Long wheel base in (mm) 219.4(5572) 17 x 7.5J Tires Spare tire Overall width in (mm) 72.8(1850) Overall height P235/75R15 With roof rack in (mm) 74.0(1880) P265/70R16 Without roof rack in (mm) 70.1(1781) P265/75R16 Front Track in (mm) 61.8(1570) P265/65R17 Rear Track in (mm) 61.8(1570) Full size Wheelbase Short wheel base in (mm) 125.
WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY VEHICLE IDENTIFICATION When planning to drive your NISSAN vehicle in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. Therefore, avoid taking your vehicle to areas where appropriate fuel is not available.
LTI0130 QR25DE engine ENGINE SERIAL NUMBER The number is stamped on the engine as shown. LTI0127 VQ40DE engine LTI0136 F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL The Federal/Canadian Motor Vehicle Safety Standard (F.M.V.S.S./C.M.V.S.S.) certification label is affixed as shown. This label contains valuable vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully.
LTI0133 LTI0135 LTI0133 EMISSION CONTROL INFORMATION LABEL TIRE AND LOADING INFORMATION LABEL AIR CONDITIONER SPECIFICATION LABEL The emission control information label is attached to the underside of the hood as shown. The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. The air conditioner specification label is affixed to the underside of the hood as shown.
INSTALLING FRONT LICENSE PLATE VEHICLE LOADING INFORMATION WARNING ● It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. LTI0137 Use the following steps to mount the front license plate: 1. Make holes on the plastic finisher at the location mark (small dimple) using a 0.37 in (9.
● Vehicle Capacity Weight, Load limit, Total load capacity - maximum total weight limit specified of the load (passengers and cargo) for the vehicle. This is the maximum combined weight of occupants and cargo that can be loaded into the vehicle. If the vehicle is used to tow a trailer, the trailer tongue weight must be included as part of the cargo load. This information is located on the Tire and Loading Information label (if so equipped).
Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the XXX amount equals 1400 lbs.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. ● Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts of your vehicle can break, tire damage could occur, or it can change the way your vehicle handles. This could result in loss of control and cause personal injury. 6.
WARNING ● Properly install and tighten the tiedown cleats into the Utili-track™ channel system. Also, do not attach any rope or straps directly to the channel. Failure to properly install the tie-down cleats or attaching ropes or straps directly to the channel can cause the cargo to become unsecured. In a sudden stop or collision, unsecured cargo could cause personal injury. LTI0107 1. 2. 3. 4.
LTI0103 3. Insert the cleat into the channel perpendicular to the channel as shown. Then rotate the cleat clockwise 90° and slide it to the desired location. LTI0104 4. Position the cleat so the nubs on the bottom fully seat into the channel detents.
WTI0124 5. There should be no gap between the bottom of the cleat and the top of the channel. Tighten the center bolt hand tight (20-40 inch pounds).
LTI0106 CAUTION ● Install only one cleat per section of channel. ● Applying loads at angles to the cleats greater then 45° or loads greater than 150 lbs. (header and floor channels) or 200 lbs. (side channels) may cause damage to the channel or bed.
LTI0123 1 correct installation, 2 incorrect installation WARNING Do not install accessories over the gap between the front and rear side channels. Doing this could affect the rear structure in certain rear impacts, which could result in serious injury. WTI0119 CAUTION Properly secure all cargo with ropes or straps to prevent it from sliding or shifting. Use the channel end stoppers to help secure items in the channels from sliding off the end of the truck bed.
Channel End Stoppers (if so equipped) The channel end stoppers should be used to help prevent accessories installed in the channels from sliding or shifting off the end of the truck bed. They must be installed so they are properly seated in the detents in the channel. Install the channels end stoppers as follows: 1. Remove the channel protectors by sliding them out the back of the truck bed. Properly store the channel protectors. 2.
TRUCK-CAMPER LOADING INFORMATION CREW CAB MODELS Crew Cab short wheel base models should not be used to carry a slide-in camper. KING CAB MODELS This information is provided for you to properly install a slide-in camper and is based on the National Highway Traffic Safety Administration regulations. It is recommended that, before installing the camper, you carefully read the following information and ensure that the camper meets the specifications.
TOWING A TRAILER WARNING Overloading or improper loading can adversely affect vehicle handling, braking and performance and may lead to accidents. VEHICLE LOAD WEIGHT CAPACITY The vehicle payload weight capacity shown on the Tire and Loading Information label, see “Tire and Loading Information label” in this section, indicates the maximum total weight of passengers, optional equipment (air conditioning, trailer hitch, etc) and cargo that your vehicle is designed to carry.
MAXIMUM LOAD LIMITS Maximum trailer loads Temperature conditions can also affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automatically decrease engine power. Vehicle speed may decrease under high load. Plan your trip carefully to account for trailer and vehicle load, weather and road conditions.
Towing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load. The vehicle and trailer need to be weighed to confirm the vehicle is within the GVWR, Front GAWR, Rear GAWR, Gross Combined Weight Rating (GCWR) and Towing capacity.
To determine the available towing capacity, use the following procedure. 1. Find the GCWR for your vehicle on the 9Towing Load/Specification9 chart found later in this section. 2. Subtract the actual vehicle weight from the GCWR. The remaining amount is the available maximum towing capacity. To determine the Gross Trailer Weight, weigh your trailer on a scale with all equipment and cargo, that are normally in the trailer when it is towed.
TOWING LOAD/SPECIFICATION King Cab 2WD (4 cyl) King Cab 2WD (6 cyl) King Cab 4WD (6 cyl) Crew Cab 2WD Crew Cab 4WD Towing Capacity*1, *2 3,500 lb. (1,588 kg) 6,500 lb. (2,949 kg) 6,300 lb. (2,858 kg) 6,300 lb. (2,858 kg) 6,100 lb. (2,767 kg) Tongue Load*2 350 lb. (158 kg) 650 lb. (295 kg) 630 lb. (285 kg) 630 lb. (285 kg) 610 lb. (276 kg) Gross Combined Weight Rating 7,936 lb. (3,600 kg) 11,133 lb. (5,050 kg) 11,133 lb. (5,050 kg) 11,133 lb. (5,050 kg) 11,133 lb.
Hitch ball Weight distribution hitch Choose a hitch ball of the proper size and weight rating for your trailer: This type of hitch is also called a “load-leveling” or “equalizing” hitch. A set of bars attach to the ball mount and to the trailer to distribute the tongue weight (hitch weight) of your trailer. Many vehicles can’t carry the full tongue weight of a given trailer, and need some of the tongue weight transferred through the frame and pushing down on the front wheels.
2. Measure the height of a reference point on the front and rear bumpers at the center of the vehicle. tem. Follow the instructions provided by the manufacturer for installing and using the sway control device. 3. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within 0 - .5 inches (0 – 13 mm) of the reference height measured in step 2. The rear bumper should be no higher than the reference height measured in step 2.
● When towing with the hitch ball mounted to the rear bumper, do not make sharp turns. The trailer may contact the bumper and cause damage to the bumper or trailer. Tire pressures ● When towing a trailer, inflate the vehicle tires to the recommended cold tire pressure indicated on the Tire and Loading Information label. ● Trailer tire condition, size, load rating and proper inflation pressure should be in accordance with the trailer and tire manufacturer’s specifications.
Pre-towing tips ● Be certain your vehicle maintains a level position when a loaded and/or unloaded trailer is hitched. Do not drive the vehicle if it has an abnormal nose-up or nose-down condition; check for improper tongue load, overload, worn suspension or other possible causes of either condition. ● Always secure items in the trailer to prevent load shift while driving. ● Keep the cargo load as low as possible in the trailer to keep the trailer center of gravity low.
To drive away: 1. Start the vehicle. 2. Apply and hold the brake pedal. 3. Shift the transmission into gear. 4. Release the parking brake. 5. Drive slowly until the vehicle and trailer are clear from the blocks. 6. Apply and hold the brake pedal. 7. Have someone retrieve and store the blocks. ● When going down a hill, shift into a lower gear and use the engine braking effect.
● Do not use cruise control while towing a trailer. ● Some states or provinces have specific regulations and speed limits for vehicles that are towing trailers. Obey the local speed limits. ● Check your hitch, trailer wiring harness connections, and trailer wheel lug nuts after 50 miles (80 km) of travel and at every break. ● When stopped in traffic for long periods of time in hot weather, put the vehicle in the P (Park) position.
UNIFORM TIRE QUALITY GRADING DOT (Department of Transportation) Quality Grades: All passenger car tires must conform to federal safety requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
EMISSION CONTROL SYSTEM WARRANTY REPORTING SAFETY DEFECTS (US only) READINESS FOR INSPECTION/ MAINTENANCE (I/M) TEST Your NISSAN vehicle is covered by the following emission warranties: If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying NISSAN.
EVENT DATA RECORDERS WARNING Always drive the vehicle in a safe and prudent manner according to traffic conditions and obey all traffic laws. 1. Start the engine when the engine coolant temperature gauge needle points to C. Allow the engine to idle until the gauge needle points between the C and H (normal operating temperature). 8. Stop the vehicle. Place the transmission selector lever in the P (Park) or N (Neutral) position. 9. Turn the engine off. 10. Repeat steps 1 - 8 at least one more time.
OWNER’S MANUAL/SERVICE MANUAL ORDER INFORMATION the type of personally identifying data routinely acquired during a crash investigation. To read data recorded by an EDR, special equipment is required and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer and NISSAN dealer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.
IN THE EVENT OF A COLLISION Unfortunately, accidents do occur. In this unlikely event, there is some important information you should know. Many insurance companies routinely authorize the use of non-genuine collision parts in order to cut costs, among other reasons. Insist on the use of genuine NISSAN collision parts! If you want your vehicle to be restored using parts made to NISSAN’s original exacting specifications – if you want to help it to last and hold its resale value, the solution is simple.
10 Index 4WD warning light . . . . . . . . . . . . . . .2-15 A Active brake limited slip (ABLS) system (if so equipped) . . . . . . . . . . . . . . . . .5-32 Active Head Restraint . . . . . . . . . . . . . .1-6 Air bag (See supplemental restraint system) . . . . . . . . . . . . . . . . . . . . .1-51 Air bag system Front (See supplemental front impact air bag system) . . . . . . . . . . . . . . . . .1-59 Air bag warning labels . . . . . . . . . . . . .1-66 Air bag warning light. . . . . . . . . . .
Precautions on child restraints. . . . . . . . . . . .1-21, 1-32, 1-45 Top tether strap anchor point locations . .1-27 Child safety rear door lock . . . . . . . . . . . .3-6 Chimes, audible reminders . . . . . . . . . . .2-21 Cleaning exterior and interior . . . . . . . . . .7-2 Clock . . . . . . . . . . . . . . . . . . . . . .4-17 Clutch Clutch fluid . . . . . . . . . . . . . . . . .8-14 Clutch interlock (clutch start) switch . . . . .2-33 C.M.V.S.S. certification label . . . . . . . . . .
Fuel Capacities and recommended fuel/lubricants. . . . . . . . . . Fuel economy . . . . . . . . . . Fuel gauge . . . . . . . . . . . Fuel octane rating . . . . . . . Fuel recommendation . . . . . Fuel-filler cap . . . . . . . . . . Fuel-filler door and cap . . . . . Fuel-filler lid . . . . . . . . . . . Fuses . . . . . . . . . . . . . . . . Fusible links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2 .5-21 . .2-7 . .
Headlight and turn signal switch. . . . . Headlight control switch . . . . . . . . . Headlights . . . . . . . . . . . . . . . . . Interior light . . . . . . . . . . . . . . . . Light bulbs. . . . . . . . . . . . . . . . . Low tire pressure warning light . . . . . Low washer fluid warning light . . . . . . Passenger air bag and status light. . . . Personal lights . . . . . . . . . . . . . . Security indicator light . . . . . . . . . . Warning/indicator lights and audible reminders . . . . . . . . . . . . . .
R Radio Car phone or CB radio . . . . . . . . . . Compact Disc (CD) changer . . . . . . FM/AM radio with compact disc (CD) player . . . . . . . . . . . . . . . . . . . FM-AM radio with compact disc (CD) player . . . . . . . . . . . . . . . . . . . Steering wheel audio control switch. . . Readiness for inspection maintenance (I/M) test . . . . . . . . . . . . . . . . . . . . . . . Rear power windows . . . . . . . . . . . . . Rear sliding window . . . . . . . . . . . . .
Headlight control switch . . . . . . . . . .2-25 Hill descent control switch . . . . . . . . .2-31 Ignition switch . . . . . . . . . . . . . . . .5-8 Overdrive switch . . . . . . . . . . . . . .5-15 Power door lock switch . . . . . . . . . . .3-4 Rear window and outside mirror defroster switch . . . . . . . . . . . . . . . . . . . .2-24 Turn signal switch . . . . . . . . . . . . . .2-28 Vehicle dynamic control (VDC) off switch . . . . . . . . . . . . . . . . . . . .2-31 Windshield wiper and washer switch .
Washer switch Windshield wiper and washer switch . Weights (See dimensions and weights) . Wheels and tires . . . . . . . . . . . . . . Wheel/tire size . . . . . . . . . . . . . . . When traveling or registering your vehicle in another country . . . . . . . . . . . . . Window washer fluid . . . . . . . . . . . . Windows Locking passengers’ windows . . . . . Manual windows . . . . . . . . . . . . Power windows . . . . . . . . . . . . . Rear power windows . . . . . . . . . . Rear sliding window . . . . . . . .
MEMO
GAS STATION INFORMATION RECOMMENDED FUEL: For 2.5L engine. Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). For 4.0L engine. NISSAN recommends the use of premium unleaded gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research octane number 96).
QUICK REFERENCE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
