USE AND MAINTENANCE MANUAL AUTOMATIC ROUNDING DIVIDERS
Pagina 2
CONTENT 1 - GENERAL 2 - PRODUCT INFORMATION 2.1 VOLTAGES 2.2 POSSIBLE VERSIONS 2.3 MATERIALS USED 3 - PRODUCT CONCEPTS 3.1 WARNINGS 3.2 DESCRIPTION OF THE PARTS COMPOSING THE MACHINE 4 - SAFETY 4.1 DANGER DUE TO MECHANICAL COMPONENTS 4.2 DANGER DUE TO ELECTRICAL COMPONENTS 4.3 DANGER DUE TO HYDRAULIC COMPONENTS 4.4 DANGER DUE TO LACK OF HYGIENE 4.5 DANGER DUE TO NOISE 5 - TRANSPORT AND UNPACKING THE MACHINE 5.1 TRANSPORT 5.2 UNPACKING 6 - INSTALLATION 6.1 POSITIONING AND MAINTENANCE 6.
1 - GENERAL It is important to read this manual and comply with the suggestions and/or rules for unpacking, installation, use and maintenance of the machine. If the machine is sold, the manual must be given to the new owner. Only operators trained for use and having read the manual can operate the machine. The manufacturer's warranty obligations only apply to defects arising from correct use of the machine, as described in this manual.
2 - PRODUCT INFORMATION After sales support: contact the retailer. All machine data are outlined on the serial number : Modello/Mod. ST A 20 Data/Date 05 / 2016 Matricola/Serial Number 90166275 Voltaggio/Volt. 400 V-50/60 Hz-3 ph Potenza/Kw 0,75 kW Ampere/A 2,21 A Peso/Weight 200 Kg MADE IN ITALY 2.1 VOLTAGES All the machines are supplied as standard with a 400 Volt 50 Hz 3 phase connection. On request: different voltages can be manufactured. 2.
3 - PRODUCT CONCEPTS 3.1 WARNINGS The following signals warn the operator of possible danger due to mechanical or electrical components. Before using the machine, you need to carefully read this manual and follow the instructions. Ensure the warning adhesives are in good condition and, if necessary, replace them. When you use the machine for the first time, carefully follow the instructions, to avoid unpleasant surprises. Do not allow unqualified staff to use the machine.
3.
4 - SAFETY . Remove the plug from the electrical power supply during machine maintenance. . Only qualified and well-instructed staff can carry out mechanical or electrical operations. . The machine must be used by one person at a time. . Do not remove the guards when the machine is on. 4.1 DANGER DUE TO MECHANICAL COMPONENTS . The safety guards protect all the parts. Keep them on during normal operations. All the guards are controlled by a micro.
5 - TRANSPORT AND UNPACKING THE MACHINE 5.1 TRANSPORT The machine must be transported in its original packaging. It must be moved with an adequate lifting system to avoid damaging it and injuring yourself. . Do not position anything on the package. . The machine must always be transported in a vertical position. 5.2 UNPACKING The machine can be sent packaged with a pallet and cardboard, cage or crate.
6 - INSTALLATION 6.1 POSITIONING AND MAINTENANCE The machine must only be installed by qualified and authorised staff. The machine must only be used for the purpose of dividing or dividing and rounding dough. The warranty is not valid if changes are made without the manufacturer's authorisation and/or if non-original spare parts are used. Use of non-original spare parts can damage the machine and/or harm the operator. The machine must be positioned on a solid and regular floor. The machine is very stable.
7 - PRODUCT DESCRIPTION 7.1 SCOPE OF THE MACHINE Rounding dividers are machines that enable cutting a piece of raw dough in small parts and then, thanks to the oscillating plate rounds every single piece, to obtain balls of equal weight and shape, all in just a few seconds! N.B.: all parts in contact with the product are suitable for the food industry 7.2 UNPERMITED USE OF THE MACHINE The divider can only be used for the activities described in chapter 8.
7.4 HOW THE COMMAND KEYPAD WORKS 7.4.1 WORK PROGRAM SELECTION To select the program to work with, keep the knob pressed for 3 seconds (the display highlights relating to the program); turn the knob to the right or left to increase or decrease the program number. Once the work program is chosen, confirm by pressing the knob once. 7.4.2 CHANGING THE WORKING TIMES e To change the working times, keep knob "e" pressed for 3 seconds (the program number is highlighted).
* t 1 (pressing time) This parameter identifies the time needed to evenly distribute the dough inside the basin, to ensure in the cutting phase each piece is the same weight and volume. ** t 2 (rounding time) This parameter identifies the time needed for the oscillating plate to shape the balls after the cutting phase.
8 - HOW TO WORK WITH THE MACHINE 8.1 WORKING CYCLE The phases follow for correct use of the rounding divider 1. Position the main switch in the | ON position 2. Insert the plate with the weighed dough inside the machine, paying attention you insert it correctly 4. Close the guard casing 5. Press the green Start key Pagina 14 3. Set the pre-selected program for the working cycle see chap. 7.4.1 6.
8.2 USEFUL ADVICE To obtain a good product, proceed as follows: . Do NOT put flour on the shaping plate. . Be sure the dough has the right pre-leavening time; . Place the dough (the dough must stay inside the plate imprints); . If the dough is sticky, put flour on the dough. 9 - JUDGING THE RESULTS The following information will help you obtain the best possible results. The pieces of dough are not the same weight? .
10 - MAINTENANCE 10.1 DAILY MAINTENANCE To clean the machine daily, follow the phases as outlined below 1. Remove the upper casing by unscrewing the specific fastenings (x2) 2. Open the fastening thrusts (x2) 3. Open the cutting unit accompanying it to the support a The machine will automatically display the "CL" cleaning program as shown in the image below 4. Press the "Start" button "a"; the knives will exit the machine for cleaning 5.
7. Close the fastening thrusts (x2) 8. Place the upper casing by screwing in the specific fastenings (x2) . Check the two fastening thrusts are correctly coupled. If not, they can cause serious damage to the machine. 10.2 PERIODIC MAINTENANCE To ensure the machine works properly and, in particular to ensure a long life, you are advised to periodically clean the ring on the head (see instructions below).
TECHNICAL DATA ROUNDING DIVIDERS no.
Pagina 19
Reproduction forbidden. The illustrations and technical data in this catalogue are for indication purposes only and are non-binding. The manufacturer reserves the right to make changes, without prior warning, to the technical data and the characteristics of the products at any time for the sole purpose of improving their characteristics.
