Network Video Recorders Quick Guide Version: V1.
Thank you for purchasing our product. Contact your local dealer if you have any questions or feedback. No part of this manual may be copied, reproduced, translated, or distributed in any form or by any means without prior consent in writing from our company. Contents of this manual are subject to change without prior notice. No statement, information, or recommendation in this manual shall constitute formal guarantee of any kind, expressed or implied.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Default IP, Username and Password Default IP address: 192.168.1.30 Default admin username: admin Default admin password: 123456 (intended only for first-time login and should be changed to a strong one with at least 8 characters including upper and lower case letters, digits and symbols for security) Disk Installation Caution: Disconnect power before installation. Use antistatic gloves or wristband throughout installation.
plates, secure all disks on the mounting plates, and then fix the mounting plates in the device. The dotted lines indicate the cable connection side (may vary with device). Make sure the disk faces the correct side for installation. Choose an option as appropriate. Use a 1# or 2# screwdriver as needed. All photos are only for illustration. 1 or 2 HDD Installation 1. Loosen screws on the rear panel and both sides. Remove the cover. 2. Connect data and power cables 3.
to the disk. halfway. 4. Slide the disk in the screw holes. 5. Tighten the screws. 6. Connect the power cable to the 7. Connect the data cable to the motherboard. 8. motherboard. Put the cover back in place and tighten the screws.
4 or 8 HDD Installation 1. Loosen screws on the rear panel. 2. Press with both thumbs and slide open the cover. 3. Loosen screws on both sides. 4. Take out the mounting plate. 5. Secure disks on the mounting 6. Place the mounting plate back in plate and tighten the screws. place.
7. Tighten screws on both sides to 8. secure the mounting plate. 9. Connect power and data cables to the disk. Connect the data cable to the 10. Put the cover back in place. motherboard. Tighten screws on the rear panel. Take Mounting Bracket as an Example 1. Identify the left and right 2.
mounting brackets. 3. brackets. Choose a way as appropriate to detach the front panel. Loosen the screws to detach the front panel. 4. Press the latches on both sides to detach the front panel. Align the disk with the slot, insert 5. and push gently till it clicks in Install all disks in the same way and then install the front panel. position. Ports, Interfaces and LEDs The ports, interfaces, connectors, power on/off switch and LED indicators may vary with device model.
Audio output Grounding PoE ports Power on/off USB HDMI output DC power VGA output Network Audio input RS232 (for maintenance) eSATA interface Alarm input/output CVBS output AC power Power on/off Network Grounding 12V DC output RS485 Audio out/input USB HDMI output VGA output HDMI output 9
LED PWR(Power) RUN(Operation) Description Steady on: Connected to power. NET(Network) GUARD(Arming) Steady on: Connected to network. Steady on: Arming is enabled. IR ALM(Alarm) CLOUD HD(Hard disk) Steady on: Normal. Blinks: Starting up. Steady on: Activated for remote control. Blinks: Authenticating device code. Steady on: Device alarm occurred. Steady on: Connected to cloud. One HD LED only: Steady on: No disk; or disk is abnormal. Blinks: Reading or writing data.
Live View Click Menu > Camera > Camera. The discovered cameras are listed. Click to add a camera. To search a network segment, click Search. If a camera is added but live video is not available, check network connection and make sure the correct camera username and password are set in the system. Modify if necessary. Playback Right-click a preview window and then choose Playback to view video recorded on the current day.